Recently active
Current set of default piping components/fittings located at <creo_load_directory>/text/piping_data/fittinglib/ are valid for Spec-Driven Piping only. These fitting parts are missing datum points witch would enable their use in manual piping. Secondly these fittings have naming conflict in instances. PTC See tech support case: C12412047, C12457308.
Dear Sir, When I am adding screws automatically through IFX, the generated bolt nut is having interferences becuase bolt is modelled on major dia and nut is modelled on minor dia. I have an assemblies where I have more than thousand parts including screws and nuts. When I am adding screws through IFX and doing global interference check, the result is always filled with screw interferences, therefore it is difficult to identify real intereferences. Why dont PTC make the library model nut part with hole major dia and put the cosmetic thread as internal minor dia. I think in this method there would not be any interferences in library part. Regards, Jayanta Sarkar
I opened a case with tech support as explained below:1) create an ecad board design in creo2) create a extruded cut inside the pcb geometry3) export the board into idx file format4) import the idx file in an ECAD SW (Zuken, Cadence, ecc.)5) verify that exported hole is imported as board outline instead ecad holeThis is a big pain if you have an ECAD-MCAD collaboration, because every time an idx file is exchanged between the mechanical and electronic engineer, they have to manually adjust the result of the export.This is the answer i got from second level TS:"Hello Mr TOSIN,I am in charge of this request regarding the export of cuts as holes from Creo Parametric for ECAD part or assembly.SPR 2221054 was reported for such issue and here is the R&D information:“Exporting cuts as holes (using the config option ecad_export_cuts_as_holes set to yes) works in the following manner:For each board cut, it collects its geometry from the board (only what intersects board geometry), and only if
There is an issue regarding schedule for fittings in Specification driven piping.1. Changing Pipe SIZE - OK.Example for a 90 Bend fitting .ptd file:"SCH_RATE" "SIZE" "NSIZE" "BSIZE" "END_TYPE" "NEND_TYPE" "FITT_MODEL_NAME" "WEIGHT""40" "2" "" "" "BW" "" "N004E0504-P281""80" "6" "" "" "BW" "" "N004E0801-P281"This .ptd file works fine and when you change the pipe size from 2 to 6 in the 3D model, then the fitting (90 Bend) is automatically replaced from fitting file N004E0504-P281 to N004E0801-P2812. Changing Pipe SCH_RATE but having same pipe SIZE - NOT OKThis behavior should also work if you only change the SCH_RATE but have same pipe size.Example is a Sweepoflange (Olet fitting):"SCH_RATE" "SIZE" "NSIZE" "BSIZE" "END_TYPE" "NEND_TYPE" "FITT_MODEL_NAME" "WEIGHT""140" "2" "12" "BW" "FLGR" "N021B1104-P888""120" "2" "16" "BW" "FLGR" "N021B1303-P888"SCH_RATE is basically the wall thickness of pipe&fittings. The example doesn't work properly in the 3D model, when you switch
There should be functionality that allows a user to show an annotation or BOM balloon for bundles (or wires/cables) in Pro/Cabling. You can show reference designators on a drawing but there is no automated way to add a note (annotation/balloon) to a bundle on a drawing.
Currently each help segment is just that, a stand-alone segment that if followed directly would not lead to success. The About Configuring ModelCHECK is a good start, as is the ModelCHECK Overview. But it just seems you have to read a bunch of different articles to get the full picture of how it all goes together. Perhaps there is a better way to describe the use of ModelCHECK that doesn't require taking a course.PTC Did this way back in 2001 it looks like at this link: http://support.ptc.com/carezone/tutorials/files/modelcheck. Perhaps a simple updating and expansion of that document would meet this need, and include it with the documentation set or link to it in the help.
Sustainability of the size of adjusted datum plane to an edge even after removing the original edge with cut or solidify.After removing solid, it would be nice to keep the size of a Daum plane adjusted to an edge.Warning message: Reference of datum outline (id 27333) is no longer in geometry; using default.
Hi,ModelCheck can rename features in the modeltree with "PRT_DATUM_RENAME / ASM_DATUM_RENAME", he can also rename layers with "PRT_LAYER_MOVE / ASM_LAYER_MOVE" command.In my company, old models have orientations in German. In our new templates, we did put them in english.However, It would be a good thing to implement a feature that allows to rename the orientations with ModelCheck. This way old models can be entirely "cleaned" with modelcheck out-of the box possibilites.Thanks.
The CREO View ECAD Compare utility is really strong when viewing what's changed in a design. It would be even more powerful to communicate to 3rd parties what's changed between a known version and the latest. The problem is that there is not a good way to generate a human-readable file that really tells you what's changed. Ideally, you would need to take all the changes from a ECAD Compare session, show the graphical A vs. B from CREO View and a quick explanation. We are currently doing this manually by viewing all the changes and take screenshots to build a document that can be shared. It would be great to press a button like "Create Comparison Report as PDF". Then, you can share the PDF with all the changes found through CREO Compare with whoever you want or need to.
In its current form, if a user is inserting a fitting in non-spec-driven piping, a window appears to allow the user to select their desired entry-ports and orientation points. However, this window does not show any of the datums if the model is saved with its layers turned off. Therefore, if the layers are hidden for that model, there is no way for a user to select those coordinate systems or points. Even a CTRL+F does not show results on a first try (a hidden work-around is to force it to find the coordinate systems by manually changing the "look-in", and simply re-selecting the model in the pop-up window.Please change this window to include a model tree and layer tree. This would probably be the easiest way to solve the hidden-layer issue.
Manufacturing: Why has the 3-axis-trajectory no tool kerf ?We have began to program with PTC-Manufacturing in the year 1997.In this time the custom trajectory was the only way to program. I don't know exactly, but I think in Wildfire 1 or 2 came the new 3-axis-trajectory.First we didn't use this way to program, but now we are using Creo2 and we won't use the custom trajectory anymore.The new 3-axis-trajectory became in the meantime a very good tool.But we are missing the tool kerf so much.Please make it possible that we get the tool kerf in the new 3-axis-trajectory.Thank you, Bernd
The symbol_spell check definition from the Creo 2 ModelCheck help says:"Checks drawing symbol for spelling mistakes. If any are found, you can highlight them or highlight an correct them. Also, you can add the word to the dictionary so that ModelCHECK accepts it as correct."Looking on PTC's site document CS191447 says:The check option SYMBOL_SPELL works only for symbols with a variable textPTC's own help files says nothing about it only working for variable text.Even though this check should be considered a bug according to PTC's help files I would like the symbol_spell check to check ALL words in a symbol. It shouldn't matter if it's variable text or not.
Currently in Creo 3.0 you are able to set the color of a manufacturing volume (mold volume/mill volume) in wireframe mode only. While in shaded mode, the volume is blue regardless of the color you set it to.***Give the user the ability to color the manufacturing volume in both shaded and wireframe mode.****
We would like to have a configuration option in ModelCHECK for checking of all family table instances when the generic is checked and when an instance is found in an assembly. This has to be a complete check including all checks that ModelCHECK is set up to preform. DETAILED DESCRIPTION:This is applicable for the following two use cases: 1. When running ModelCHECK on a generic part. A complete check on all family table instances should be preformed. 2. When running ModelCHECK on an assembly containing a part instance. A complete check on the parts generic and all family table instances should be preformed.
Similar to how most other CREO files have iteration #'s, add the iteration number ( .1, .2, .3 ...) to the end of the file name of creo_parametric_customization.uicreo_parametric_customization.ui.1creo_parametric_customization.ui.2creo_parametric_customization.ui.3This allows recovery of a setting that may have been changed unintentionally. The previous customization file "config.win.x" used the iteration number.
I would like to propose an idea to add a command that allows you to put some locations in a group so that they can move together simultaneously. I often find myself having to use some tricks to make the network between them bribes so that the cables pass through the network by autorouting, but then, if I want to move those locations I need to move them one by one. Adding the locations in a group It would be easier.
Now in drawing module in Creo Parametric you see all of lines in the same thickness (but in different colours for different type of lines). In prepared drawing in pdf you see real tickness (conerted by pen table). It will be cool to see real tickness of all of lines in process of drawing in Creo.Here you see that solid line and hatch line in the same thickness (first picture) , but it will be cool to see it in real different thickness (second picture).
currently, removing Component Names (from ECAD_REF_DES column) by using the NAMES menu in MODEL PROPERTIES, does not remove the REF DES LABEL note. Since the note is just an annotation method to show the name, it should not be there when the names are removed. Users are forgetting to remove the note after removing the names are are confused why it still shows when they are showing the reference designators.This is in reference to case 12958332.
Hi.I would like to suggest new function "Split Surface by Curve".This function exists in Creo Simulate - "Surface Region".I need same functionality in Creo Parametric.Note:There is also automatic splitting in Moldesign.ThanksRegardsMartin Stary
Referring to PTC Case C12994725, my company has legacy parts which have been in use for many years which directly conflict with IFX part names. The parts are used throughout our products making renaming of the legacy parts unworkable as I would have to open hundreds or possibly thousands of assemblies during the rename. These legacy parts are stored on a network drive for common usage. When I initiated use of Creo 3 with IFX the assemblies failed due to constraint mismatch with the new IFX parts. I found that the IFX parts were loaded before any search.pro from my config.sup or config.pro. I tried turn off the IFX functionality using the config.pro option. No effect.My suggestions as to possible solutions are: allow a search.pro called from the config.sup to load before the IFX search.pro, rename the IFX parts to include the prefix AFX_ or IFX_ to differentiate them from any customer legacy parts, or turn off the IFX search.pro when the IFX functionality is turned off.
Today, wirebonds cannot be imported via IDX as the file format does not support them. This request is to work with the IDX consortium to allow the exchange of wirebonds between electrical CAD tools and mechanical CAD tools. Our company designs a number of products that use wirebonds, and in the ECAD / MCAD exchange process, these circuit card features are not translated. Additionally, there is no alternate flow that will provide a way to get the wirebond structures into Creo Parametric, along with all of the other electrical components, for communication of changes through IDX.
Currently, ModelCheck will only find extruded holes that should be regular holes, if the user creates only one hole in the extrude. So the user has a choice..either:1 - Use a hole feature, which is a little more work, and our current company policy, or..2 - Use the loophole, (which makes his life even easier) and extrude all holes in one sketch!If there are more than one hole in one extrude sketch, CYL_CUT_SLOTS will not be flagged in ModelCheck. I believe this doesn't promote proper modeling behavior, rather it promotes the loophole, which is even worse. Please improve the checking process for this.Thank you.
When trying to Save an Assembly that has a WindChill Modification Conflict with a submodel, and then setting the Action to READ ONLY, the Assembly will not be saved initially. Saving the assembly again WILL work. This is critical as users think their work is being saved initially and then they end up losing everything if they close out of Creo without saving again. The small error message is not enough. There should be a use-case scenario within the software that saves the assembly even if a submodel is set to READ ONLY.PTC says that this is a change in behavior and thus, this improvement idea is created!
Add functionality to the piping module that allows for beads to either be created or shown on the end of pipe segments. Currently beads need to be created outside the piping module as a separate part & assembled or as a assembly feature. Both methods do not allow for full association to the pipe feature itself.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.