Recently active
bj p,I took your attached model and applied a symmetry constraint, just to show that symmetry does work in Creo Simulate. Whenever the model and loading has symmetry, use symmetry constraints. This will reduce your run time. I know that you place a rigid link on the bolt, but I removed it just to show the effects of bolt bending using symmetry, and the rigid link can be easily restored. Also, I put a surface region on the bolt up to the surface of the bracket (surface region is 25 mm long), and the load is applied to this surface without going through the bracket hole. Usually when there is a load applied to a bolt, there is bending of the bolt, as you can see in the attached displacement. I attached my model, just in case you want to look at it and run some investigations.Hope this helps.
You've already downloaded Creo View Express 3.0, but I just wanted to post this incase there are some other users that might want to see what it looks like. You can get it for 32-bit or 64-bit. I've used Express and Adobe for viewing, and Express is a much better tool, as shown below.You have the following extensions when saving from Creo Parametric:
Amazing. I will have to try this.
Creo View Express is much better than PDF, and Express is free.
Creo View Express is free, but you cannot view STEP files with it. I think James is looking for a STEP viewer. If his shop just wants to view models, then .pvz files will work just as well as an alternative, and yes, it's free. Good point.
Perhaps I'm not understanding what you're asking, as you can see in the below image, I have a part that is gray with cream surfaces on the cuts. Maybe this is not what you're asking.
Hi Dhiraj,Do you have an image with a description of what you're trying to simulate? This would be very helpful if you could upload a description. Sometimes it depends on the region of interest of data recovery as to where and how to apply constraints. Welcome to the forum.By definition:
Are you talking about a single part, or a part within an assembly?
Are you trying to create the "bulge" that protudes back to the center of the wheel?
Hi James,Creo View MCAD will allow you to view STEP files. Demo link attached:http://www.ptc.com/product/creo/view/mcad
An abundance of partner exhibits, educational resources and networking opportunities await you in the Solutions Expo June 15-17. Whether you’re looking to learn something new, expand your network, win prizes or relax, the Solutions Expo is your must-visit destination while attending at PTC Live Global.So, what can you expect at the Solutions Expo?50+ exhibits by PTC partners, who offer complimentary products and solutionsAccess to 160+ PTC product experts that will help you save hours of work (and re-work) The chance to test drive PTC Creo 3.0 and discover new functionalities in PTC Windchill 10.2.A first glance at the innovative Internet of Things Pavilion – Powered by ThingWorx, where you’ll discover first-hand the power of smart, connected products More than nine hours of demos and opportunities to chat with peers and presenters – and walk away with ideas to improve your product design and developmentAnd there is room for some fun and relaxation in the Solutions Expo as
Matt,You can see a full description of each option in the attached pdf, which is in the Help Center, along with all the new enhancements for each new release under What's New.
What’s Next for AT&T’s User-Defined Network Cloud?AT&T recently launched the next phase of its Cloud Networking architecture — the AT&T User-Defined Network Cloud (UDNC) — at Mobile World Congress. Having often written about AT&T’s cloud initiatives, I thought I’d provide some context for the latest announcement and strategy, which builds upon our ongoing virtualization journey.Where we have beenThe first step in the journey was the virtualization of the Wide Area Network (WAN). AT&T introduced our MPLS Virtual Private Network (VPN) services years ago, and customers world-wide have adopted them to run their enterprise networks. We think of MPLS as the first wave of virtualized service. In essence, we virtualized the wide area network, creating a flexible, multi-tenant platform with such enterprise features as logical separation of customer traffic, class of service, and network security.Where AT&T is nowCloud Services The IT industry is also well alo
Uvolněna oficiální verze aplikace AV ScriBatch Tools 1.0 pro hromadné modifikace a exporty objektů v prostředí Pro/ENGINEER a PTC Creo Parametric. Ve společnost AV ENGINEERING, a.s.vyvíjíme aplikaci pro dávkové zpracování modelů, sestav a výkresů, která podporuje operace s parametry, relacemi, přejmenování a přesouvání prvků, nastavení vlastností modelů (hustota, přesnost, materiál atd.), umožňuje export do PDF/DXF/DWG, nebo hromadný Backup dat projektu včetně navázaných výkresů. Aplikace navíc umožňuje napojení na PTC Windchill a provádět automatický check-out / check-in, tedy dávkově importovat data do Commonspace.Na základě několikaměsíčního provozu aplikace v Beta režimu ve čtyřech desítkách společností využívajících PTC Creo Parametric, se nám ve spolupráci s uživateli podařilo aplikaci odladit do té míry, že jsme se rozhodli představit již její oficiální verzi:AV ScriBatch Tools 1.0 Pro představu o nové podobě a funkčnosti aplikace jsme připravili prezentaci, kterou můžete shlédn
I think you can make a sweeping cut in Creo Parametric 2.0. Just watch the attached video.http://www.youtube.com/watch?v=3umkwp8t_AA
PTC Branded Steering Wheel Concept by Juan Carlos Flores Here is this week's Member Showcase Roundup, demonstrating our members' expert use with designs, 3D models, worksheets and how-to's: Pattern Boundary Blend Surface By Huu Huynh System of units in Mathcad / System of digits in Mathcad By Valery Ochkov BOXX Introduces X-Generation Workstation (Custom PTC Creo Models) By Vladimir Palffy Component wire frame in cross section? By Denny Coauette Test Your Knowledge of PTC Creo and PTC Mathcad By Bettina Giemsa How to know the last page of the element? (Arbortext) By Robson Soares Boneti Plot a function with a vector as its input variable By New Jap Multiple convection coefficients? By Paul Bunuan Feel free to click on any of the links above to discuss, like, rate or reply to any of this weeks' posts. Congratulations to our highlighted members for their incredible contributions this week. Have you had a chance to de
The data exchange for assemblies is: step_export_ap214_asm_def_modeThis is for Creo 2.0, and you can see this in the attached pdf file.
You could use FloEFD with Creo for CFD analysis.
Attached is the latest config options from PTC for Creo 2.0 M100.
Center console boat render by Alex McCarleyHappy tax day to all our friends in the USA! Hopefully you've already filed your papers and are sitting back comtemplating what to do with the GIANT return you're due. Here is this week's Member Showcase Roundup, demonstrating our members' expert use with designs, 3D models, worksheets and how-to's:How to create curve profile in Pro/ENGINEERBy Haris TSDerivative of functionBy Sameer Fares (Gallery)By Jeremy ConnaughtonHow to save calculated data for later useBy New JapYet another Thread thread - UTS ImplementationBy Antonius DirriwachterBy Jayanta SarkarTelescope Visual Limiting Magnitude (Mathcad worksheet)By Fred LuskExport Annotation by STEP or IGSBy Luca CarraroEditing Reserved ParametersBy Gregory S FranksFeel free to click on any of the links above to discuss, like, rate or reply to any of this weeks' posts. Congratulations to our highlighted members for their incredible contributions this week.Have you had a chance to demonstrate your e
You start by process of elimination. After you open the part in question, you can start from the bottom of your model tree and suppress features until you find the problem.
First, I would open component T400204_GA (which is unconstrained in the assembly) and perform a save as and work on that component by itself to see why you cannot group some of the features. Look at some of the features and you will see a double wire box.
Hi Sasa,First, try to Group items 64 and 65 (Extrude 4 and Extrude 5). Is this an assembly?
Hi Kirby,You may scale an assembly or part by Model>Operations>Scale Model the enter the desired scale as shown in the below figures.Figure 1Figure 2
Hi Marius,The current config options is attached, which is also a searchable document.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.