Recently active
I would really like to see the model, how it was constructed for the finite element method.
Checked out and locked source member of code type RPG, then converted to RPGLE and now need to promote up entity that is a different type code of RPGBND, how do I accomplish this? I recall I use to do this with F7=Fold and could change the object code type there while keeping my lock. Check out as one type and check in as different type... Member name stays the same... how do I accomplish this... am on Implementer release 2005
I saved a spur gear yesterday as .stl, and I tried to reduce the size (KB). It went from 151 KB down to 77 KB, by adjusting the chord height and angle control (shown below).
Paul,Are you allowed to upload the model and some screenshots of the real-world problem along with a description of the problem (loads, constraints, region (s) of interest)?
If you have coincident surfaces, isn't this the same thing as mating surfaces? If so, wouldn't the tool Pairs Clearance tell you if the surfaces are coincident? Example shown below.
You can IMPORT NX files into Creo Parametric 3.0, but it will import as a neutral file.Welcome to the forum.
Paul,Whenever a gravity simulation is used, I would highly recommend verifying the total weight of the model. I use the IPS system of units and 1g = 386.4 in/sec^2. After you build your model, run a quick check to verify the total weight. For example, you can run a 1g load in one direction and see if the resultant load in that direction matches the weight of the model.
Jeffery,You're refering to .stl not .stp, right?
Praveen,Before opening any files, I would recommend scrolling down the folder tree (as shown below) and selecting the folder where the target file resides. Then make that the Working Direction by RMB. Whenever I launch Creo 3.0, the Working Directory defaults to My Documents (set up that way), but I'm always changing it to different folders.
Andrew,When I open the attached drawing, this is what I'm seeing. Is this correct?
Dan,The below image is a gear that was created in ST6, and imported into Creo Parametric 3.0 (M010). After importing, notice that there are no features in the model tree, except for the import feature. However, once the model has been imported, it is a workable solid or surface. For example, if you imported a simple beam, you could cut or add features to the beam. If you have the Flexible Modeling Extension, you can modify some existing features such has holes, thickness, rounds, etc, and this will be added to the modeling history. It's important to have the Flexible Modeling Extension if you're going to be working with imports.Welcome to the forum.
Thanks. That did it.
You can extrude it to a surface that is part of the solid geometry, as shown below:
After importing a model, I cannot change the color of the entire part at once, only by clicking on each surface. Is there a way to correct this?
I already tried those methods, and none of them worked for me. I have attached the part.
Works really nice with freestyle surfaces (shown below):
Mahesh,Thanks for sharing this information, as I was able to replicate it too (shown below). I wasn't aware of this functionality.
What is the weight of the object before removing holes?What is the target weight?
Good. I've been out of the office for the past couple of weeks, so I'm sorry that I didn't get back on this one. But you figured it out on your own.
It appears that inifinte friction will hold the block on the disc. Finite friction is a slippage indicator, and the components bond together.
This model was just an experiement, and there are a lot of warnings in the run summary. So I don't have a lot of confidence in the solution. I built it just to show myself it wouldn't work, because of the unconstrained block. Assembly attached.
Cameron,I never tried a problem like this before, but I made an assembly, disc and block, and ran the model with angular velocity. The bore in the disc was held with a pin constraint, and there is an infinite friction interface between the disc and the block. I didn't think this model would run, because the block is not constrainted. See below images.Figure 1: ModelFigure 2: Displacement Plot
Moha, You may want to try sketching the six sections with equal number of entities, sweep it as a solid, notch out the relief, then shell it. This way, you won't have to worry about using the round feature. Just a thought. Images posted below.Welcome to the forum.
M010 has the capability to import SolidEdge parts and assemblies. I imported the attached SolidEdge gear. FYI.
The draft worked for me with Creo 3.0 F000, up to 89.9-degrees, and I'm already up to M010.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.