Recently active
Rocks1,If you have just a box with hardware, such as hardware from a library, and the hardware has no csys, then by all means, just mate it with the hole.I have to deal with large airframe assemblies, such as stringers, skin panels, floors, longerons, intercostals, etc., and they are assembled upon one csys, the csys of the airframe. Also, I receive them this way from the aerospace companies, such as Sikorsky, Boeing, and Lockheed.
It's very simple. When I'm building an assembly, I have already created all my components based upon the assembly csys, so the component csys and the assembly csys are the same. When I add the first component to the assembly, I just snap the component csys to the assembly csys and it's fully constrained and very stable. Then I just repeat this with the remaining components. This is a common practice in the aerospace industry where entire aircraft are assembled this way, such as the H-60.
I put a comment in your other post:https://www.ptcusercommunity.com/docs/DOC-6827
Whenever I'm putting assemblies together, I referenced all the components to one cys, and I don't have any problems.
The message Outdated Component/Feature is a notification for components or features with references that have changed since the last regeneration.The only way I know to fix these notifications is to open each failure and make new references. This is fairly easy to do, but it sounds like you have a lot of them to fix.
For the type of font you have selected, it may be the right behavior. It depends on which fonts you select. Some of them will dip below the line, and some will not, as shown below.
A common modeling error is users make a reference on the geometry and then change the geometry, breaking the reference. Try to make references off datum planes, axis, csys, and points, references that won't change throughout the assembly or component.If you have a large assembly, it may be that the references to other datum planes have been broken.
Ruben,You can connect the two pipes using the Extrude method without using the Shell. For example, the below images show the two pipes coming together by extruding the longer section up to the surface of the first section. The two pipes have the same OD but different ID, so they are different in thickness. Hope this helps some.
Adam,Are you referring to the Options in the below image (Creo Parametric 3.0 M020)?
Are you opening the Assembly in Creo Parametric or Windchill?
Can you upload run summary file (.rpt)?
With more than 330 sessions at PTC Live Global, June 7-10, you might feel scared when it comes to finding content that is relevant to you. But with the new Session Catalog we’ve launched this year, that task becomes much easier than in the past.Additional ways to search sessions:To the traditional search filters: PTC Product Family/Content Theme, Session Type, Target Audience and Content Level, we’ve added a few more: Timeslot, Presenter Name and Presenter Company.The “Timeslot” filter will let you pull content within a specific timeframe. This is particularly useful when you identify a session you’d like to attend, but want to know what else is happening during that same timeslot. This way, you’ll be sure you don’t miss anything important.The “Presenter Name” and “Presenter Company” filters will let you focus on a specific presenter or a company. At the same time, it’s a good way to have quick access to a list of companies and individuals presenting at the event.Cross-searches:This ye
Calum,Are you attempting to run the stress analysis in Creo Simulate? If so, I'm very curious as to how you're going to mesh the assembly. I just attempted to a mesh a simple plate (shown below), and I made the plate as thin as possible (0.0009-inch or 28.86 um), and for now, that's as thin as I could get it using absolute accuracy. Both of your coatings added together are 0.0006-inch. I've never attempted to mesh geometry this thin before (never had a need too). For the moment, I don't know how thin Simulate will go, as I'm still experimenting. I would really like to know the outcome of your mesh, if you're willing to post it.
Look at the attached video and see if this helps. It switches to Mechanisms after about a minute of play.https://www.youtube.com/watch?v=7leLhYQj3qo
Hey all - We've been live on the new version of our software for exactly one month and I just wanted to thank all of you for your help getting us here! There have been a lot of great questions and feedback posted within this group and on our Community Help group during our beta and after our launch period and I really appreciate all of your contributions. If you have any questions for Tmetcalf or myself please don't hesitate to reach out.Best,- Ryan
Domen,If you don't mind me asking, what software version do you use?
Here is some related info on bending a pipe: https://community.ptc.com/t5/Creo-Modeling-Questions/bend-unbend-of-hollow-pipe/td-p/310191
If you're viewing a drawing with dimensions and without a csys, you should still be able to make the pipe. Sketch a curve (trajectory) and make a sweep on that curve.
So you answered your own question. Can you mark your own question as Correct?
Anyone done this with PSM ? We have a custom one with sitescope monitoring.Was wondeting if there are any better versions and if PTC is planning to provide something along these lines...
Erik,I greatly appreciate you posting your findings, as it gives us all insight, and what not to do with a 360-degree cone with a pressure load, something I wasn’t aware of.If PTC has resolved your problem, could you post the discussion as Answered? This will benefit others who are searching for solutions.I very seldom run SPA .
Were you able to solve the problem?
Frank,If my suggestions have resolved the problem, could you mark the discussion as Correct. This will benefit others who are searching for solutions. Thanks.
Alvin,If my suggestions have resolved the problem, could you mark the discussion as Correct. This will benefit others who are searching for solutions. Thanks.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.