Recently active
There is currently no easy way to replay Sequences in Creo View without having to watch the entire step and then restart it. It would be ideal to have a timeline implemented so that the user can scrub through the scene similar to how you can do that in Creo Illustrate.
Create an option that allows you to transfer the item list to another illustration. At the same time, if the item list changes, it will also be updated in all the illustrations to which it was transferred. The initial task is to have one table with a parts list and several figures for it (as in the pdf file)
As of now PTC is supporting only Adobe Reader for Creo View Clients to read PDF documents. But we need support for other PDF readers like Foxit Reader, Nitro PDF etc.
Currently the only way to create a projection measurement in Creo View in a vector that is not aligned with the default CYS is to load a MCAD license, create a CYS, take a measurement, select projection and select the created CYS. I would propose that instead of creating a CYS the user be allowed to pick a surface or edge through which to project a measurement similar to the way that Creo Parametric works.
Feature request: Playback controls for playing creo illusrate animation/sequences are extremely limited in Creo View Express. No option to stop or rewind animation after play has started. Also, no option to scroll through animation. This would be helpful for operators during assembly.
When creating sequences of 10, 20, 30 plus instruction illustrations the option to change the order of the illustrations as displayed in the figures pull down list aids content management greatly. It gives an instant overview of the sequence of your illustrations and helps to avoid continuity mistakes. At the moment I'm having to do this by exporting figures one by one as I go and managing them in Adobe Acrobat. This is clumsy and adds costly unnecessary steps to the work flow. This function exists in other 3d illustration packets.
The ability to export the whole set of figures (batch export) contained in a creo illustrate file all at once helps to reduce production time and would be a good improvement for creo illustrate. This exists in other 3d illustration software.
Instead of perform design check outside the .prt or .asm, it could be good to have an apps that have the same features of PTC Creo View Design Check.With this embedded direly inside the creo model, the designer could have access to the review without opening creo view. And make the update in line with the request.It could be just to have an apps that open the model in a geometric simplification mode and have annotation and measurement possible.
Would like to have the functionality to cancel, in Creo, the last "propose change". today this is the number 1 issue with ecad-mcad collaboration and cause many failures in the process.
I have been tasked with creating cabling harnesses for a next generation space telescope for NASA at Goddard Space Flight Center. Our traditional method of harness manufacture is to build a mock up structure, run all the cables on the mock up, and then transfer the harnessing to the actual spacecraft. With this method we have to do an immense amount of guesswork and add in a lot of extra room to make sure that everything will fit. As of right now there are many many areas for improvement within the cabling module and Creo itself that I would like to submit for submission. There is currently no method for making changes to a cable short of deleting it and rerouting it manually. NOTHING updates parametrically. This is a massive departure from the way that Creo works and markets itself. Please change this. If I run a cable and then have to change the spool or diameter - Delete and Rerun If I run a cable and need to change the end lo
To avoid or find out the use of 3D Creo-Models with certain Lifecyclestates (e.g. PROTOTYPE, INVALID) in large assemblies it would be fine when Modelcheck could check the content of a locked parameter that comes from Windchill. Unfortunately Modelcheck is unable to check the content of locked Windchill-Parameters like PTC_WM_LIFECYCLE_STATE in the direct way. Of course it is possible to go the indirect way and map the content of the locked Windchill-Parameter via a relation to a new Creo-Parameter. The new Creo-Parameter can be checked by ModelCheck and everthing workes fine. The problem is that the relation has to be added in every part, subassembly and assembly. It would be fine to get the Lifecycle information direct from the locked Windchill-Parameter. In that case it would be sufficient just to show the content of the parameter (read-only). Changing the content should be functionality of Windchill as it is at the moment.
Inspection dimensions defined in *.mi files coming from Creo Elements Direct Modeling are unexpectedly interpreted as normal dimensions at retrieval in Creo Parametric
Hello there, I am trying to conduct an animation where a cable dynamically follows the connected connectors which are moving based on different constraints that I apply. So far, I cannot find a way to see the dynamic change on the cable shape due to the movement of the connectors. Can you please have a look on this idea and let me know how can this be applied to Creo Parametric? Thanks. Kind regards, Pavlos Zairis.
If the Selection Radii are changed from within a design that uses inch units, it causes a rapid spiral to them becoming zero whenever any changes to any of the options are made. In spite of the statement “Radius dimensions are shown in screen units that do not depend on sheet units and the zoom factor” PTC customer service has verified with the programming team that they actually are metric units. If you look at them with a design sheet open that has inch units, they will be 1/25.4 of the radii you see without any sheets open. If you change the values while in the sheet, the numerical value of the inch dimension will be transferred into the default value without converting it back to millimeters. The next time you open a design, the program reads the numerical value as millimeters and divides it by 25.4 to “convert” it to inches, making it. If you change ANY option (not just the Selection radii), this process happens each time: assuming that the numerical inch values is mi
Currently, an Augmented Reality ThingMark or Spacial Target that is created in Creo is visible within the model AND all higher level assemblies. It would be great it we can have visibility support for this so that higher level assemblies aren't overcrowded with these items. Either, have these features not shown at all in higher level assemblies, or have a def_layer config, like: def_layer LAYER_DATUM_PLANE 1_ALL_PLANES I know we can create a layer with rules, but that gets tricky with legacy models and our current setup uses def_layer for everything. Thank you!
I was hoping to get feedback on the attached model. It was created in Creo 3.0 M130 as a sheetmetal part. The feature I am seeking input on is the flat_pattern/bend_back. The relations measure the part, outputs measurements to parameter and the smt_thickness drives the material parameter. The family table instance for the flat pattern supresses/resumes only the bend_back for drawing/deliverables. Thru Pro Program, I manually moved the bend_back to the end of the model tree to keep the measurements in the flat_pattern feature "live" at all times. (Creo forces flat_pattern to bottom.).
Hi PTC Developers! I recommend to improve Creo/Parametric when Pro/Program IF condition is in use - please fix the problem with stopped Undo / Redo functionality.I have very much advanced parts with parameters managing the model tree but our users are unhappy due to lost functionality of these vital buttons: . Thanks in advance! BR, Roman
When using a Merge/Cutout/Intersect/Inheritance feature, with the reference type set to LOCAL, the preview image of the base model is in the WRONG location. This is when the feature is undergoing an EDIT DEFINITION with the part opened (not active in a subassembly). The response from R&D on this is that it is working as expected. The added note is that the outline is not the preview and that the Merge/Inheritance has no quick preview. The outline seen is from the active collector. This is not intuitive as the image shown during the edit definition is incorrect, whether you call it a preview or active collector. This is confusing and should be fixed. Reference ticket 14024534 and SPR 7312670.
Steps to reproduce: Open assembly Switch to hidden lines view Print to 2D PDF with MS printer driver or Save As PDF Current result: blurry raster image, no texts (text as rater image) in the PDF Suggested result (maybe by option): export precise vector graphics and searchable text to the 2D PDF
Make it possible to have Obj as output from Auxilliary applications through the C++ Toolkit
today to move a dim. in Creo 4.0/5.0 : 1. hover over the dim 2. left click to mark it 3. left click and hold to move it. that makes alot of click when working in 2d. a better way would be: 1. hover over dim 2. left click and hold to move it
For a Creo Drawing, we have a requirement to create "Scalable Vector Graphics (SVG)" file. Creo Parametric 3.0/Creo Parametric 4.0/Creo Parametric 5.0 does not have an option to export (save as) SVG output file interactively from UI and also Creo Toolkit API does not have an option to generate the SVG output file.
There is a complete set of routines in order to manage Assembly simplified reps., but it seems that Part simplified reps. have a different behaviour....
In an effort to standardize our sheet metal parts, I have been searching for a bulletproof model structure to accurately and consistently measure the flat state for blank sizes. Our standard practice has always been develop the part model through adding features, unbend, measure, bendback, and an unbend or flat_pattern which is suppressed. (UMBF for short) We then create a family table instance for the flat state that will be used in deliverables, (a drawing for forming operations and flat pattern geometry for export to CAM software) The issue with this practice is the measurement can be incorrect if features are placed after the "UMBF", the measurement feature references fail or do not regen, or are not oriented correctly to reflect the true OAL and OAW . The flat state includes measurements, (SMT_FLAT_PATTERN_LENGTH & SMT_FLAT_PATTERN_WIDTH), but can also be incorrect if the flat state is suppressed as the FLAT_PATTERN feature is inherently for
Hello, The save_texture_with_model configuration option controls whether images are embedded in models and drawings. It would be useful for us to have separate options for 3D models and 2D drawings, for example: save_texture_with_3d - Controls whether images are embedded in 3D models save_texture_with_2d - Controls whether images are embedded in 2D drawings The reason for this is that we have 2 different use-cases: 3D Models - Typically textures/decals from a library that are used across many different models 2D Drawings - Typically images that are specific to that particular drawing Thanks Tim
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.