Recently active
Local stress concentrations are inevitable in most models. If I try to optimize feature sizes so that failure index>1 I want that optimization to ignore the FI of any elements that are at P=9. To be sure, I DO want simulate to show those hotspots in the post-processor... I just need it to ignore them when calculating features sizes.
Lumped masses should not be a part of "total mass" or, there should be another system parameter that clearly conveys the mass of all the actual geometry being analyzed. Including lumped masses in any optimization designed to minimize "total mass" messes up the ability of the optimizer to successfully optimize structure. Think of designing two small brackets that are being designed to support some heavy object between them. The heavy object gets designed as a lumped mass and it can easily weigh 10X what each of the brackets weigh. The optimizer "sees" very little change in "total mass" even when making large changes to dimensions of the bracket.
Formerly in Creo 3, a HTTP path could actually be used to reference models in Creo. This was used for a time to pull for example, a curve .ibl file from a version control system like Subversion, into an import feature. The HTTP path was convenient because it provided a clear lineage instead of directing to a user's local path. This functionality does not seem to work anymore in Creo 5, and PTC confirms that this was never within spec. This would be good to put back in the spec for the above reasons.
According to PTC document CS138583 is not possible to have both dimension name and its value in the same dimension object so we would like to request this to be added in future release as part of our process require to have that information in the same object. Note from PTC document:Note : Both the dimension value (@D) and its name (@S) cannot be displayed at the same time in a single dimension object. It is possible to add a first dimension through Show annotations option, display it as a symbol (@S) and then add a second dimension manually referencing the same entity to have the dimension value displayed.
Maybe move display_annotations from Configuration Editor to the Annotate ribbon, it would make it easier to turn annotations on and off.
Within a sketcher we can't edit a spline point that has any dimensions or constraints when the spline menu is active. We want to see the analysis of the spline and then edit the dimensions as required. We need to first close the analysis, edit or delete the dimensions and then go back in and check the analysis. Or we need to delete the dimensions and constraints and THEN we can manipulate the spline points in the spline tool.
Bring the functionality that Creo Simulate has to specify units in whatever format you want to dimensions in modeling. If I have a requirement driven dimension in one unit but I am working in another set of units it would be great to leave the requirement dimension in the original unit for ease of double checking.
Add back a function that just selects parent so I can use it in my mapkey. Nobody got time to look at that tree and desipher from the part name which parent they want. We just want to click a part on the screen and keep smashing our 'select parent' mapkey until the appropriate parent is highlighted.
If a layer state is defined, it is displayed in the lower left corner. Same for simplified reps, x-sections, clipping, etc. This display needs a toggle other than temporary shade. Also, GD&T Advisor automatically puts notes in the bottom left corner, which overlap these state displays. Therefore the location of the state displays should be configurable so they can be moved to, for example, the lower right corner, above or below the tolerance display.
Currently Creo Options Modeler enables us to create options list using the .vsp file or by manually checking the options in order to create a variant spec. We currently have more than 500 variant specs where it becomes difficult for us to manually create the options list for each specific variant. It would be great if it has a API which can drive the options list using the data from the spreadsheet and create the Variant spec for each variant.
Unable to read arrow size for dimensions and leader lines for all annotation types using Pro/Toolkit. We are unable to get details of the arrow size using any available API. Is there is a rule of thumb or heuristic which will enable us to determine the arrow sizes for annotation leader lines and dimensions as displayed in Creo Parametric?
As of Creo Parametric 2.0, 3.0, 4.0 & 5.0 there is no API yet introduced that would provide the text orientation of a dimension (Default / horizontal / Parallel to and above leader / Parallel to and below leader) using ProToolkit.
When a Copy Geometry feature is made, elements copied into the new model may respect the original layer state of the reference model. This is known via CS6554, CS195989, CS231128, and CS302330 and is current functionality. A user should be given the option to ignore the original layer state. The current functionality causes an issue in many scenarios, such as - Copying geometry from another model with a slightly outdated layer model. The recent upgrades to Creo 5 have demanded some tweaks to layers (feature based instead of entity based). Any models following this old layer model will continue to obey this into new models, sometimes in conflict with new layer rules. - In the reference model, the item is in a Hidden or Shown layer. This will persist into new models that the item is copied into. The latter situation can happen easily by accident (driving sketch for an extrude/revolve that is autohidden). From a UX standpoint, this is in direct conflict with the new eas
Hello all,Need to add functionality of auto numbering in any symbols variable text when set to integer type.Due to this it will be easy to add balloon notes and other sequencing symbols in drawing.This i am demanding the functionality same as the draft datum feature available from Creo 4, where datum feature is placed in sequence like A, B, C and so on and if user type the already used name it gives warning by red underline.So same functionality we need for symbol numbering. This can be done by simply adding some kind of syntax in Creo. So R&D guys please work on it because we already have similar kind of syntaxes but in Datum symbols and Repeat region table (rpt.index).Jignesh.
Now it is possible to set the Dimension Boundaries for existing dimensions (selected or All), but for new features the Dim Boudaries is set to Nominal again. This is confusing and results in errors. A Config Option to set a default would solve this problem.
Please add ability to Creo Parametric to allow flexible parts and assemblies to be replaced by another part or assembly with out removing flexibility. Thanks, Don Anderson
Saved optimization/feasibility design studies (behavioral modeling) may frequently require modification of constraints, parameters, or optimization settings. Currently, if a saved design study is modified it cannot be re-saved directly. Instead, the user receives an input error: "The supplied name is already used. Type in another name". If the user needs to keep the same name for the optimization, the process is: 1) Open design study and modify, 2) Delete same design study, 3) Save as new. The proposed idea would allow a modified design study to be saved without first deleting it: 1) Open design study and modify, 2) Save as modified. I think this should be the default behavior, but a config option would be an acceptable solution also.
It is recommended that the character height that is pasted by copying the note character be the character height set in the note.
I would like to see a Model Tree Column info that shows if a feature "has children" (yes/no) to help cleanup legacy models being copied and re-used. By quickly being able to see in columnar form which features do not have children (the "yes" would not necessarily need to be displayed for my purposes but the "no" definitely) helps greatly to quickly identify features which may not be needed and could be deleted from these new models carried over from legacy.
When you utilize Creo + Windchill it could be nice having a visualization of the components' status directly in the model tree.Even now it is possible, but only through by adding columns with text inside; this scenario means a large model tree on the screen and a bad visualization (in my opinion). What I suggest is the presence of the same windchill icons inside the model tree. So, if a component is under checkout, I gonna see the blu/yellow square in the tree.Obviusly, this should be an option activable on request by config.pro or similar thing.
Insert in the config option the item that enables the "Clean Pro/Program code for new models" option.
When the = (equal) constraint is picked it should filter out centerlines as centerlines can not be equal to anything.
Would like a function that will show me the references for a created dimension. Currently in Creo 4.0 M09 there is no way to do this. You can edit the attachments of the dimension, but this does not show the existing references. User created a dimension, another user modified the design and was complaining about dimension not updating or show as out of date. When looking at the dimension it appeared he was correct, but in fact the first user created the dimension wrong. There was no way of finding references for created dimension. Case was created with PTC, which resulted in waste of tech support time. Please consider adding this functionality. Wayne Schrock
Hi, in Drafting. user can add the dimension with the tolerance. but in Creo there is check box to display tolerance upper limit and lower limit. but there is no API in creo toolkit to know whether that tolerance upper limit and lower limit is visible or not. please plan to add an API to get the tolerance upper limit and lower limit is visible or not in drawing. Regards, Vipresh shah
Sketch dimension constraints looks, not so productive. We can't see the dimension until we apply it, and if it's not what we need, we need to delete it, and then make a new one. When we create a fillet in sketch environment, some dimensions disappear, we need to create them again. I think sketch needs some improvements, to ensure CREO productivity. Remember that every feature, needs a sketch!
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.