Recently active
One of the most frustrating changes since moving to creo 3 is that everytime I need to measure something I am required to hold my pinkie down on the control key. WHY?! Do you think engineers are accidentally left clicking everywhere? If I am left clicking then I intend to select something when I am in the measurement tool. Get rid of the control key. Left click to select geometry. That's it.
Currently there is no setting to export transparency information. You can read this in CS22317.But You can nowhere read when it will come. The problem is that other vendors support this feature.It's time for Creo to have settings for the export as STEP with transparency as well.
1. Describe the Problem Reference: Ticket - 17688221 Article - CS438652 We were trying to create a mapkey that turns off the navigator bar. The trail file shows: mapkey(continued) ~ Command `ProCmdNavigatorBtn` 0; - this is supposed to turn it offmapkey(continued) ~ Command `ProCmdNavigatorBtn` 1; - this is supposed to turn it on However, when generating a mapkey, the 0 or 1 will just toggle the navigator. Meaning, you can run the mapkey 3 times and it will turn off, turn on, and then turn off again. It should not be like this. A 0 should be off and a 1 should be on. That's how 99% of all other commands work. All on / off or open / close commands in Creo should ensure they are not toggles, so people can properly write mapkeys that are repeatable and work in all situations. 2. Are you using a workaround?No. We just hope the user has the correct setup before they start the mapkey, or else it won't work as designed.3. What is the use case for your organization?We are tryi
1. Describe the ProblemHi,I suggest combining the "Optimization/Feasibility" and "Sensitivity" modules into one. There are no differences between the dialogues except for the "steps."These modules are widely used. Separating them into two dialogs necessitates a double setup, as almost every optimization process is preceded by a sensitivity analysis. 2. Are you using a workaround?No3. What is the use case for your organization?All development processes4. What impact does this problem currently have on your organization?Simplify procedures
1. Describe the Problem ProUIAction does not have any settings for Row selection. 2. Are you using a workaround?Handle actions on ProUITable rows via ActiveActions that configure separate ProUIButtons.3. What is the use case for your organization?ProUIList provides a good selection environment for users. For example, when multiple selections are required, users can easily adjust the selection through the L-Shift button. When a list that combines multiple elements is required, ProUITable can be used. When using ProUITable, L-Shift affects cell or row selection. Selecting a cell and selecting L-Shift like a checkbox is not a good experience. In order to provide an experience like selecting all/deselecting all like the checkbox of ProUIList, a separate button is required. This button requires two elements, one for selecting all and one for deselecting, and provides a messy UI. If the checkbox is located separately, it can be combined with the MIXED state to provide a richer experience for
1. Describe the Problem Reference: Ticket - 17702670 Article - CS438511 Currently, if we want to specify a certain ecad area to be void of more than one type of region, we need to create separate features. As we try to progress with our ecad mcad collaboration journey, we sometimes hit bumps in the road. We try to remind each team that overall, the process should be quicker. However, we clearly have a workflow here where it is not quicker. Working with a drawing, the engineer can reference one sketch and manually type in that it is for placement, routing and vias - quickly. However, now, they need to spend time to create and manage 3 features. Although this may not seem to be a big deal for some, for others it is. I believe there is room for improvement, where one feature can control all 3, with collaboration. 2. Are you using a workaround?Creating multiple features.3. What is the use case for your organization?See above4. What impact does this problem currently have o
1. Describe the ProblemWe are seeking for automatic way as inheritance feature already under machining part, we require output as below picture were casting row will add below machininging row with below format only.2. Are you using a workaround?No Work around, We have raise a PTC tech Support request Ticket Number: 176733463. What is the use case for your organization?To create BOM extraction from Creo to Upload in SAP PLM4. What impact does this problem currently have on your organization?We need to do it manually and take more productive time, we need to reduce time by Automating this process.
Currently, there is a ModelCHECK configuration option in the condition.mcc file called MODEL_TYPE. And it allows the following 8 values:PRT_SOLIDPRT_SHEETMETALPRT_SKELETONPRT_PIPEPRT_HARNESSASM_DESIGNASM_INTERCHANGEASM_MOLD_LAYOUTWe'd like to request that this list includes additional model types - notably entities created in the piping module, harness assemblies, and envelope models. We'd like to run different ModelCHECK items on them based on their model types.Right now, we are looking at using a parameter as a way to differentiate model types that are not part of the 8 supported types shown above. But we'd rather have PTC support it though ModelCHECK.Thanks.
1. Describe the ProblemThe ProAnnotationTextstyleSet() function from Creo Toolkit will change the font style of an entire system generated note, instead of individual lines. If you want one line to have a different font style than another on a system generated/parametric note, you must change it manually.. The issue is described in this article: https://www.ptc.com/en/support/article/CS1635602. Are you using a workaround?Manually changing the font style3. What is the use case for your organization?The standards require that view scale, detail view and section view notes have size 6 filled font on the first line, and non-filled font on the second line. Users must manually change the font settings in order to achieve this. However, if ProAnnotationTextstyleSet() had the capability of changing each line's font individually, then we could create a tool that would do this automatically;4. What impact does this problem currently have on your organization?More time and cost spent ma
1. Describe the ProblemWould like tools to improve the quality and length of time it takes to detail drawing. Much of our work is very similar but may just have different number of holes/features etc.. We have a vast library of previous drawings that a new drawing should be similar to.The AI tool should be able to recognize how we layout our drawings and create views, display model dimensions, adjust tolerances, update/create datums and GD&T tolerances. I know PTC believes drawings are going by the wayside, but we still use them. I believe the vast majority of your customers also still use them. This could then eventually also be applied to MBD. 2. Are you using a workaround?None available3. What is the use case for your organization?Improve the quality and length of time it takes to detail drawing.4. What impact does this problem currently have on your organization?Consistency, Quality, Performance.
1. Describe the ProblemWith the introduction of Tables in 3D mode, PTC has made an important step towards MBD with Creo 11. What we are missing here, is the opportunity to re-use data from the 3D file properties, such as Name, Number, Weight, etc. so basically the repeat region feature which is available for tables in 2D mode.This is currently explicitly excluded in the PTC Documentation:https://support.ptc.com/help/creo/creo_pma/r11.0/usascii/index.html#page/whats_new_pma/mbd_create_tables.htmlLimitations: Currently, Creo does not support tables with repeat regions. When you place a table with repeat regions, a message appears in MBD, and the table is placed as a simple table.Feature Request would be to enhance the tables make them re-use attributes already available instead of manually typing all the information into it.Documentation for Repeat Regions: https://support.ptc.com/help/creo/creo_pma/r11.0/usascii/index.html#page/detail/Understanding_Repeat_Regions.html2. A
Customer requires additional test criteria G-LO-LG based to VDA 4955 standard.
1. Describe the ProblemPTC removed from J-Link the ability to modify parameters on objects that were checked-in. 2. Are you using a workaround?Have no workaround.3. What is the use case for your organization?Our workflow was check-in drawings, then we ran a custom app called Print Release. This app opened drawings, temporarily modified parameter for the date and time. Created a PDF file and put on our network. This gave us the ability to see on the PDF when the drawing was released to the shop. We did NOT have to have the drawings checked-out. We wanted drawings checked-in before print release so the iteration number shown on PDF matches iteration number in Windchill.4. What impact does this problem currently have on your organization?Our drawings NO Longer have the release date & time on them. If there happen to be problems, it is more difficult to know when the drawing was released. PTC should NOT be removing functionality that has been there for many years. Customers spend
1. Describe the Problem There is currently on option for specifying a company specific Bulk Item template file. I would like to see a template_bulkpart config.pro option so we can specify our own start_bulk.prt file. 2. Are you using a workaround?Inform the users that they cannot use the default start part template for bulk items and they have to select our company specific start_bulk.prt file to get our parameters into the file.3. What is the use case for your organization?Prevent errors when a user creates a new bulk item part. Since they do it infrequently, they usually forget to use our start_bulk.prt and end up having to repeat the bulk item part creation.4. What impact does this problem currently have on your organization?The impact is minimal, but frustrating for the users.
Hi, in optic of MBD, it was useful to have the capabilities to create some table in 3D with Repeat Region (with the same capabilities of the 2D)
If you use the Holes feature to create annotations after creating a hole, the arrow does not point toward the hole center. When measuring the diameter, the arrow points to the hole center. The user tries to use the drawing annotation by modifying the holetable, but the arrow direction is not centered, making it difficult to use. (The direction of the arrow measuring the diameter is toward the hole center.)
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo Illustrate 11.12. What is the problem?It's been confirmed after issuing a case, that Illustrate is not managing 2D figures properly. They are affected by different situations like monitor resolution and even the zoom of the view in Illustrate while activating a figure page. After importing a picture as 2D figure it's size is not the same of the imported one and is wrongly affected by the zoom view (unlike the 3D symbols which always have the same size)3. Are you using a workaround? If yes, please describe it.There is no workaround unless manually stretch/resize the 2D picture and/or remembering of adjusting the page zoom before adding it4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.We ran into this issue because we have streamlined the process in creating pictures with a m
1. Describe the ProblemWhen creating a simple hole and adding tolerance to it, the note callout doesn't contain the tolerance information.per https://support.ptc.com/help/creo/creo_pma/r11.0/usascii/index.html#page/part_modeling/part_modeling/Thread_Notes.html this can't be achived2. Are you using a workaround?Adding the information manually which resulting with error3. What is the use case for your organization?enforcing standard throughout the organization4. What impact does this problem currently have on your organization?Manual work with error
It would be greate to bring curve through points to IDD The options that exists within IDD, to create the same curves, have some workload for the same result.
1. Describe the Problem Reference: Case: 17701020 Article: CS438057 We would like to create a specific drawing that has negative value ordinate dimensions when they are below or to the left of the 0 value. 2. Are you using a workaround?No3. What is the use case for your organization?There are other tools, in other fields that have negative values below and to the left of a central origin. For example, the origin of a PCB. We would like to create a drawing, which a PCB designer can validate against their design (from our EMN import). It would be great if he can see the exact same value from our drawing to his tool. For example, a distance below the origin would show -0.25. Right now it shows 0.25, which is different from their dimensioning scheme.4. What impact does this problem currently have on your organization?It makes the downstream teams, which use the Creo drawings have a harder time consuming the data, with an increased risk of errors, miscommunication and then
Unused models in drawings can only be deleted one-at-a-time from within the drawing and are only accessible from an old DOS-like menu. Unused models can accumulate from drawing revisions, and if a drawing is copied and views are edited. You may not even know you have unused models that are taking up memory and time. Modelcheck can be used to strip unused models from a drawing, but that's another step that shouldn't be necessary. Suggestion: Cleanup the drawing model selection menu and add the ability to select multiple models to delete and/or the ability to delete all the unused models at once.
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.Switchgear, Product Design Engineer, Energy network operators2. What version of Creo Parametric are you currently running?6.0.6.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.When patterning something like fixing holes along a long bracket, it would be useful to have the functionality to define end points, or a fixed distance to act as limits at the end of an axis for a pattern feature (say the length of this bracket is 700mm, and the fixing holes should be 16mm from each end, the total length for the pattern to populate would be 668mm). Then, define either the spacing between pattern instances, or the number of instances desired, and have the software handle populating the axis with either the maximum number of instances that will fit between the defined points/distance, or the required num
While creating a split draft one side only, Creo still takes into account the radii on non-draft side of the split which can cause the feature to fail creation. When creating a split draft (one side only) have Creo ignore the radii on the non-draft side of the split.
1. In an assembly, when you search/filter a model tree it works. When you activate a part or sub assy, the search/filter no longer applies to the whole top level assy. The reason for asking this is the ability to search for cabling components from within the cabling mode. 2, when saving the model tree CFG files it will not retain the search/filter check you set for searching for paraamteres within the assembly
When CAD tools have seen the day, the web was very modest(only static websites), now it has been invaded by web apps. Thanks to the power of Javascript, frameworks like(Angular, React, Vue, Ember, etc.) made it possible to have many desktop applications as web applications. Providing Creo as a web application will be an important event in its history, the integration with Windchill will become more transparent than the Workgroup Managers.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.