Recently active
1. Describe the Problem When I edit a part (say put a fillet on a former sharp edge) switch to its drawing, and find that the dimension has lost its reference (to the now non-existent edge), I want to "reconnect" the dimension. This is done by right-clicking the dimension and choosing Edit Attachment- the icon with a set och chain links. However, almost 100% of the cases when I do that, the icon is missing. I have to unselect and try again, and sometimes again and again, before it appears. I wager it is related to the priority of how the dimension elements are selected. First click highlights it so it can be dragged. Second rather discerns between elements within the dimension. This is rather annoying though, because I have to peck like 4-5 times before I get to where I want to go, and if I happen to move the mouse a pixel between then I might have to try again. 2. Are you using a workaround?No.3. What is the use case for your organization?-4. What impact do
1. Describe the ProblemIn creo parametric supported surface finish symbols does not have any prefix and suffix text. To enhance the information carried along with surface finish annotation we need to have prefix and suffix text to surface finish.2. Are you using a workaround?Yes. Currently we set this textual information as parameter to annotation.3. What is the use case for your organization?We want to store extra textual information of the surface finish annotation at its prefix and suffix location.4. What impact does this problem currently have on your organization?With the current workaround we loose the visual representation of this textual information. As it is possible in case of GTOL or other annotations in CREO.
1. Describe the Problem The ProDrawingDimensionVisit function is available in Toolkit.This can be used to collect all dimensions of a drawing whose names begin with "dd", "rdd" or "add". In other words, all dimensions created in the drawing while the config.pro option create_drawing_dims_only was set to yes. When creating a Toolkit app that uses this function, we've noticed with some older drawings or drawings that were copied from older ones that the Toolkit function sometimes finds many more dimensions than are actually on the drawing! 😲 The most extreme example we've found so far is a drawing that at first glance only contains one single dimension.Even with the Search Tool, only this one dimension can be found.With the ProDrawingDimensionVisit Toolkit function, however, a total of 157 dimensions can be found on the same drawing.The 156 additional dimensions are also not erased dimensions, which could be deleted with the user command delete_erased_dimensions in th
1. Describe the Problem When an annotation is shown on a model, then called out in a note (i.e. a customized hole note), the shown dimension is not erased, creating multiple instances of the same dimension. See attachment and notice how many times dimension IDs are used in a single view. In drawing mode, the shown dimension is erased when the dimension ID is called out in a note. 2. Are you using a workaround?The only workaround we are using is to manually erase the dimension. However, this does not prevent it from being shown again using "show annotations"3. What is the use case for your organization?All models using 3D annotations.4. What impact does this problem currently have on your organization?3D annotated models have the potential to be over-dimensioned, which can lead to parts being produced wrong.
1. Describe the ProblemFrom the Familly table:- Select the column where the corresponding objects are not highlighted.It is very hard to find the object in the Graphic Area when we have la large assembly. 2. Are you using a workaround?No workaround is available.3. What is the use case for your organization?Most of the users working with Design Table objects. it is hard to find the right object in the Creo Parametric Graphic area.4. What impact does this problem currently have on your organization?Identify the family table objects, in the Graphic Area, the user needs to put in a lot of effort. More than 300 users expect this option, in our organization.
1. Describe the ProblemThere is no event before a creo file is loaded. The event should be triggered for each model before it is loaded, including each component installed in an assembly.2. Are you using a workaround?no workaround3. What is the use case for your organization?Check whether the corresponding model is still current/valid. Real-time detection of which models are loaded.4. What impact does this problem currently have on your organization?no solution available
When creating/editing annotations in Creo Illustrate, there is no option for defining the font to be used. You can only specify the Font Size and Font Colour as shown: According to PTC Support document CS116109, the default font of Arial is the only option. It would be much more flexible if users in Creo Illustrate could: Define a default font to use in the Creo Illustrate Options dialog box. Change the font for individual annotations.
1. Describe the ProblemWhen we assemble a Creo Elements/Direct Model in a Creo Parametric assembly via unite we do not have points, axis, planes or coordinate systems in the Modeling Object to define placement constraints.2. Are you using a workaround?We have to create Creo Parametric Models as a clone of the Modeling Object with the relevant datum objects. In case of a change we always have to change the Modeling and the Creo Parametric Model.3. What is the use case for your organization?We want to use the existing standard parts (Modeling objects) in Creo Parametric. The placement should be defined using datum objects like coordinate systems planes or axis.4. What impact does this problem currently have on your organization?We have to clone all the Modeling Objects to Creo. In Windchill we have a 3D Modeling model and a 3D Creo Parametric model linked to the WTpart. In case of a change we have to change both model types.
Hello erveryone, I think it will be very usefull to add the possibility to manage the font of the annotations, and for any fields with text. Thanks, BR
Adding transparency to the color, not adding it after when viewing the Cad Part, but to define it in the color itself with a percentage. Fot now it can be made as you click on the cad part itself, but not as an option on the color Palette to choose.
Reference: Case: 15627024 SPR: 11198253 Currently, if you set the config "show_geom_checks_on_creation", it will only popup a warning message when the feature is FIRST created. However, if there is no geometry check when it was created, rather the geometry check got added later during an edit definition, it does NOT inform the user via the option popup. R&D says that all new development work for notifications should really be to the new Notification Center. Therefore, this 'idea' is to have the Notification Center flag geometry checks, regardless of when or how it was created. I would like to add that there should be an option which differentiates between notifying a user in the assembly; whether the geometry error occurred within a part or via an assembly cut. I would prefer if people weren't notified about a geometry check for a small piece of a car, if they are working in the car assembly. However, if they are working in that part, then they SHOULD get th
The current method of cuts as assembly level features drives a lot of issues when dealing with complex bill of materials. When an assembly cut is made, a feature is added to the piece part level after regeneration. This causes the actual change of the geometry (whether it is adding a hole, etc.) to occur, in the model tree, way before the actual assembly feature is located. This causes changes to feature id's, etc. that impact the assembly features higher in the model tree. For example, if you create a Creo Solid Weld in an assembly, then create a machining cut after the weld, which might reflect the real life order of operations, that cuts through an edge or surface that the weld references, your weld will either fail or have a portion of the weld disappear. The work around is to create a copy of the surface or edge at the piece part level that the weld can reference. This copy exists before the assembly level feature is added to the piece part, so it is not impacted. I do not
The symbols located at <loadpoint>\symbols\report\bomballoon do not meet our corporate drafting standards, and there is no method for customizing these beyond overwriting the existing symbols in this loadpoint location. There should perhaps be a config option to allow us to point to our own custom bomballoons for this purpose, without being forced to alter the Creo Parametric loadpoint. See Article - CS23593 - How to set custom reference BOM balloons in Pro/ENGINEER and Creo Elements/Pro (ptc.com)
Hello everyone,If you like below thing that should be available in Creo Part modelling multibody THERE SHOULD BE A WAY THAT CREO ASK US WHILE COPY THE BODY AND PASTE IN THE SAME Your reply is very valuable for me
Hi, We are using Design Exploration. We are finding that there are some scenarios when checkpoints are created inadvertently, which causes the number to go higher. We then have to delete checkpoints and end up having checkpoints with numbers like 5, 13, 22. The issue is that we are building a top-down approach for engineers to select a design concept and push that out to Creo and then configure it using a skeleton with parameters. We would like the numbers to be able to be: Hidden Customizable Able to be rebuilt where the first checkpoint starts with 1 again. Thanks!
It should be possible to open a Design Exploration File from the Windchill Workspace with the open in Creo button in actions the way every other file can be opened. In addition if you are in the information page of the TMU file you should be able to click on Actions and open in Creo as well. Currently only able to open in Windchill from the normal file dropdown within the workspace.
It would be nice to create configuration option to specify the model which will be used as the default skeleton template - for example: template_skeleton
Sometimes, software requires neutral files, e.g. Parasolid or IGES, to be supplied in a specific version. PTC's position is to export in lower versions of neutral files as it maximises compatability, but the version of Parasolid particulalrly is too old to be supported by some software that is supplied to us for use with a particular piece of hardware. We require a version equal or newer than version 14. Creo Parametric can import Parasolid files up to version 38. Please also allow the ability to export in newer versions.
Currently it is possible to display the assigned material and its values for example density, mass inside the model tree but it is only possible to display the values without the unit of measurement. Right now (Creo 7.0.2.0) there is no way to add an extra column with the unit of measurement next to the value but this would of course be a valuable functionality. To display a value is useless without its unit of measurement. In this example (without units) it is not really clear how the density of the main assembly was calculated. The values of some parts are pretty much too small to have that result for the main assembly. Easy to understand if the units of measurement are beside the column (but currently not available). After changing the unit inside the parts from mm to cm the whole calculation is more understandable. The display of the values in general makes more sense if the unit of measurement could be available next to the collumn.
Reference Case: 15655921 Reference SPR: 11246232 Although we design in English units for most parts, we are using metric sheetmetal thicknesses. We have therefore changed the unit for the SMT_THICKNESS parameter and set it to be calculate. When we update the thickness dimension, it does not flow back up to the SMT_THICKNESS parameter and convert to the metric value. This parameter would be used in model-based-definition annotations (like 1mm thickness, 1.2mm thickness, etc). We want it driven from the english dimension so there are no inconsistencies. Thank you!
Reference case: 15640004 Reference SPR: 11255994 Some parameters, like smt_dflt_bend_radius do NOT update when you change the unit of the model. This is potentially a big issue. Either: The model fails and the user takes precious time to investigate and fix the issue - Not ideal The model doesn't fail and the user visually noticed the geometric differences and investigates and fixes the issue - Risky The model doesn't fail and the user didn't realize that the internal bend radius is much larger than before - Spoiler alert - It happened!. This is an issue as it impacts the model and the design. Please fix! Thanks!
In the feature who support the "sketch region" filter, there should an option of select and deselect the specific selected and non selected region. Which help in to increase productivity.(view in My Videos)
CREO offers two schemes for altering model units: conversion and interpretation. Of these, the conversion option adjusts geometry and model material properties to stay self-consistent, while the interpretation option changes units for both without adjusting either. This means that the interpretation option will alter the material properties, which requires the user to set them up again. This is especially problematic for organizations that set up models with a default material already assigned. Sometimes users may forget to change the units until they have already started modeling geometry, which requires them to use the unit interpretation option. Current workarounds consist of either using a manual scaling operation or resetting the material properties after unit interpretation. It should also be noted that this process tends to confuse new users, who generally don't expect this behavior. It would be nice if CREO included a scheme that gave the option to conduct a unit
We faced an issue with several Windchill cloud environment connections from Creo to Windchill. Creo Server Management allows (/ is intended to be used) to register several Windchill servers for one instance. We have Test, Development, QA, and Production environments, which all are running on PTC Cloud. If user tries to register all of these environments, they receive an error stating that "Server is already registered" (with two of the environments): This occurs because Creo identifies those to be the same environments (based on the IP?), even the addresses and names are different (e.g. QA https://eg1-qa.ptcmscloud.com/Windchill/ vs Production https://eg1.ptcmscloud.com/Windchill/). As these are on cloud, the public IP addresses get changed over the period of time and thus it is not efficient to register those as "local" variables on Windows. To by-pass this, we need to create environment specific starting .bat's, which are then using different Cache folders (e.g
Ticket Reference: 15668428 SPR Reference: 11556077 We have an Extrude that references the edge of a quilt by using the PROJECT command in sketcher. When we flip the direction of the quilt and then flip the extrude the feature fails. If we do an edit definition of the sketch in the Extrude and then click OK, it works again! PTC R&D says this is a 'limitation of the software'. 😭 The official word is: “The limitation is that the edges formed a counter-clockwise loop at the time of creation. So now when they go clockwise the software considers this inside-out contour and changes the material side of the extrude. The software does not recompute the orientation to preserve the user intent.” Please fix. Thank you!
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.