Recently active
When the Preference "Show drawings as children" is activated, drawings are shown as children of a 3d model. However, all drawings are shown, also the drawings where the 3d model only is a component. This means that for standard components like screws hundreds of drawings could be shown. Also this makes queries very slow. When i do an "expand all" of a large assy with the preference activated this can take hours or leads to out of memory errors. Suggestion: introduce an extra option that only shows the drawings where the 3d model is the owner. This gives more usefuil information and drastically reduces query times (in the mentioned example seconds instead of hours!)
A huge performance hit is taken when you have textures on your model and your drawing has shaded views.To my surprise, the Texture toggle button is not available in the detailing ribbon.You have to switch this in the options or in a part/assembly model.This looks like a serious oversight.Please allow the texture toggle button to be added to the detailing ribbon.
Allow for temperature-dependent specific heat properties in Simulate. Specific heat varies greatly across a material's temperature range.
When adding radiation or heat flux loads on an assembly, there is no feature to allow for the selection of all EXTERNAL surfaces of the assembly. One can only select "boundary" surfaces of each component, which results in the selection of a lot of interface surfaces which would not actually be exposed to radiation. The only other option is to select each external surface individually, which can be very tedious for complex assemblies.
Created datum planes/axis should have size relative to screen. This will make it easyer to find a plane/axis that you need in swarm of others.When you are making plane/axis on a small area of part you are usualy zoomed on it, so making datum relative to screen at that point makes sence. Creating plane as offset to part face should create plane with size relative to face.This can be config option to turn on/off this option and define size ratio to screen.Personal work example: Imagine aircraft sheetmetal part bent in 2 directions with 100`s of rivet holes and each rivet hole needs plane and axis to define hole. Creating these datums and selecting right ones is nightmare because you need to resize evry datum to avoid clutter.
Make it possible on this forum, on the left side where it shows a picture/how many post/since when, to also show the version/date code (or mulitples for some users) with which we are currently working. Or to have something like a time/date stamp that we can put in the post so that if we change versions/date codes at a future date, the post will still stay at the vesion/date code for which the question was posted.
Need an option in Pro/E drawing so we can see sketched lines drawn in the background of an inserted object(OLE) on the drawing (example inserted artwork pdf of a label drawing which overlaps the sketched border lines of the label). Lines plot fine but are not visible in ProE drawing. Ref. case C11220263.
There are multiple standards for GD&T. While some are very similar (use many of the same symbols), there are symbols that one standard will use that will not be valid in another. The current Template Browser presents many symbols, but currently does not distinguish between the standards. As a result, it is possible for users to not only mix symbols from multiple standards on the same drawing, but it doesn't make it easy for administrators to enforce a particular standard for their users.
Customer would like "Convert Geo" function that converts real geometry to construction geometry and visa versa - to be available in Creo Elements\Direct Drafting.
The "By VP Frame" method for selecting is very useful. I would like a similar method which allows you to box an area but only select those elements or objects which are visible in the viewport, so it will ignore hidden elements or objects. This could be an additional option to the "Boxing" section called "Visible". This would most likely need to be implemented based on the facet model, similar to how the Econofast mode works in Annotation. While obviously not perfect, it should be much easier than selecting all of the element or objects manually.
Windows7の64bitOSにてCreo Elements/Direct Drafting Rev18で日本語入力する際に、IMEの日本語変換ウィンドウが表示されます。 AutoCADやModelingなど他のアプリケーションではIMEの日本語変換ウィンドウは表示されずに入力が可能です。 IMEの日本語変換ウィンドウを表示せずに、日本語入力が出来るようにして下さい。
Loading a step-file, with the option „check part“ should not accept the label. Improvement suggestion: Expand the option “without label”. (show also case 11226010)in german: - Beim Laden von einer Step-Datei mit eingeschaltetem "Check Part" werden im Ausgabe-Bildschirm Infos angezeigt. (okay) Weiter werden Beschriftungen direkt am Teil angehängt. - diese sollen mit einer Zusatzoption "without label" nicht übernommen werden.
Older versions of CoCreate had an apply button when geometry settings were changed in annotation. After selecting this button, other geometry could be modified just by selecting it.With the latest version all geometry must be selected first then modified. If any geometry was missed, it must be selected and changed separately.This is a real time waster.
I do not always want to have crosshatching on clipping planes. Often, the cross hatching hides details that I need to see. It also makes it hard to show these details for reports. The cross hatch should be able to be turned off.
NPT pipe taps should be modeled as tapered in the machining module. A machinist can look at the drawing and quickly tell that the tap is an NPT pipe thread. Currently, we use a lisp routing to make the tap. however the threads do not automatically show up in annotation, so we add the threads by hand. This is a waste of time, but necessary for the correct thread representation.
Dear PTC Team / Community, We wish to suggest a modification concerning the system behaviour when opening files directly inside Creo (Menu -> File -> Open). Today, using this method, the file will always open "as latest" (please see the sketch attached below). We would like to have an option to open the file "as stored" directly inside Creo (Menu -> File -> Open). If you have any questions, please let us know. Best Regards, ThyssenKrupp Fördertechnik Latino Americana Team Bruno Castro (bruno.castro@tkfla.com.br) and Dr. Obretinow (roland.obretinow@tkfla.com.br)
I would like to be able to create an integer parameter with a blank value until it has been defined. Zero is a valid value and I would like to not have a value assigned until the object has been reviewed and the correct value determined. After the value has been entered there is no need to be able to go back to a blank, but it would be nice to be able to have an initial value of NULL.
To whom it may concern,There are only Horizontal and Vertical for a function of Broken View now.It is not suitable for long parts with an angle.Therefore, I need broken view with an angle.For example, it break for an object perpendicularly for Broken View.Best regards,
While making templates there is no model present. When adding callout &ptc_wm_version for the solid model the template adds ":D" suffix, because there is no model present that has that parameter, so it defaults to the drawing. To get around this you have to take the Creo session offline for each formate/template your company has.It seems like going in to the Template Application should create the environment necessary to make a template, and not have to go through a long arduous path of taking it session offline. The idea is to fix Template Application
Implement export of Creo drawing to WMF/EMF format. This way you enable users to put nice pictures into Service Guides (created using Microsoft Word) of their products.Notes:WMF/EMF file will contain vector image of drawing view or drawing sheetUser can import WMF/EMF file into Word documentAdditional requests:Use pentable during exportExport options:Option no.1: Export every sheet into separate fileOption no.2: Export every view into separate fileMartin Hanak
It is very complicated to untrim surface. I mean to remove triming boundary line completely or only its portion. As inside option I see switch with possibility to keep or delete original surface. Partially it is already possible to do something similar (only inside untrim) by "remove surface" button it can be good idea to have the same button for all remove or delete operations.
Give possibility to extrude not only sketches but also edges and 3d lines, circles, splines. It can be complicated because it will be necessary recognition of possible intersections to avoid crosses.
Sometimes i need to copy surface or group of surfaces. After this operation copied entities are deleted. I need it for manipulation of existing surface separately from general context. After this I integrate it in part. I immagine this procedure as one button that separate selected surfaces from quilt. It should save a lot of time.
Sometimes it is necessary to remove history of the all part or only quilt rather than export, import and lose all IDs of surfaces and edges. It can help to improve work with imported parts whet we are forced to collaborate with other 3D systems. This capability can be very useful when we work for a long time only with surfaces, the history is too long and originally part is imported.
Hello!When I insert the assembly in drawing and insert the table of that assembly and put the baloons every think is ok. Next J insert an integral piece of this composition would be good if you could put bom balloon automatically that was tied to the table and would be restored by changing the assembly parts.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.