Recently active
buongiorno,quando mi va in conflitto lo sketch che devo aggiornare i riferimenti, la finestra è fissa e non viene permesso di modificarla o ingrandirla.. perchè? nel creo 3 si poteva fare.
New users are almost universally confused by connecting to Windchill and when they get disconnected from Windchill. Windchill should get a tab in the ribbon. The tab itself could indicate when it is connected or disconnected. That would make it a lot easier to see the Windchill status and also collect the Windchill functions in Creo for a better interface.
In Creo, Can we measure center to center distance between two unsymmetrical / symmetrical feature for example distance between the center of two ribs,wall etc. I already post an issue in "All Places > Creo > Discussions". There are some ways suggested by people like creating datum point on feature, or in case feature is symmetric we can measure the their end to end wall distance. This way it will unnecessarily prolong model tree and if an another person who want to work on that part in future these extra model tree features will not indicate their true purpose and may create confusion for him. It will be great if Creo will automatically highlight mid point for such feature so we can measure the center distance between the future without adding any datum points/feature. Please see the snapshot. Snapshot include rib only. In practical cases feature could be anything like plastic part snap on and rib.
Selected CSYS in part (or assembly) should always have the same name as part (or assembly), even after renaming the part (or assembly).After RMB on CSYS, there should be the option to turn this on/off, or at least it should be possible to make this happen with relations (renaming CSYS with relation).Currently, there is only guide from PTC how to make this with PRO/Toolkit, which not everybody has (me either).
In Creo 4, PTC included a Publish option for 3D View States so users could have views that wouldn't have to publish to Creo View. This same functionality would be very useful for Drawing Sheets. I could see several use cases from this: having a DXF sheet that won't publish to PDF or maybe having a secondary page for engineering notes. Our CAD designers end up having to do a lot of monkeying around to prevent DXF sheets from messing up drawing PDF's (they create a whole new PDM object called DrawingName_dxf.drw or create DXF's drawing on the fly with mapkeys).The non published sheet would not be included the total number of sheets, every sheet would publish by default, and there'd be a way to transfer this to CAD Workers that auto publish PDFs. Here's the option shown in Creo 4 for View States:
Currently when creating a new drawing and Drawlist option is visible the option Once is always the default (see CS51461).Currently, there is no way to overwrite the default value for this option.This is, in our opinion, a potential source of error because the configuration drawlist is not updated anymore in the drawing views.We need the ability to set the default value for the option Drawlist to Always when creating a new drawing with configurations.Best regards.i.A. Anton KarevCAx-Solution ArchitectLiebherr-Hausgeräte Ochsenhausen GmbH
Network locations are not displayed in the Creo explorer unlike mapped network drives.The locations should be visible as otherwise there is a need to create mapped network drives which creates additional effort.See also: https://support.ptc.com/appserver/cs/view/solution.jsp?n=CS257844
We have a scenario where a freestyle feature requires to be mirrored in two directions. The Left side should be mirrored to the Right and the Top to the Bottom. According to the support documentation, this is not currently possible. Please seriously consider this as a future (very soon) enhancement.Thank you!
Actually components assembled with mechanism connections are not clearly identified in the Model Tree. They are in fact identified with a small icon that makes the user not adequately distinguish these components from the ones mounted with constraints (see fig. below) Orange arrow: fixed component (ground body). Blue arrow: components assembled with connections. Green arrow: component rigidly constrained on a component assembled with connections. Red arrow: component assembled with no constraints or connections at all (wrong "placement"). It would be nice if the user could clearly distinguish between packaged components and components assembled using regular mechanism connections (see an example below)
We have the below config set:def_layer LAYER_QUILT 6_ALL_SURFSWhen importing a model, it automatically assigns all quilts/surfaces to that layer, whether the feature was solidified or not. When you enter the Import Data Doctor (IDD) and the layer is hidden, the components are gone from the graphic window, but even worse - they don't show in the IDD GTS Tree either. I go from seeing a solid to seeing nothing when doing the EDIT DEFINITION. We should at least see the feature and show that it is hidden.
Similar to the drawing module, which has:Config option: pro_dtl_setup_dirModelCheck check: STD_DTL_SETUPThere does not seem to be any administrative control over a PART or ASSEMBLY detail options, which can be found in Model Properties. Please think about implementing similar control over these detail options as well.Thank you!
Integrate symbols from "Text Symbol" dialog box as buttons directly into "Note Properties" dialog box and drop "Text Symbol" button from "Note Properties" dialog box.
I am using helical sweep command to create thread profile on a circular surface. while creating drawing, I am unable to give radial dimension. the arc is converted to spline after helical sweep. In another part a cutout is created using the thread profile. we are unable to give radial dimension in this part. I am currently using Creo 3, M110 date code. Is there any way we can provide radial dimension?
Hi PTC, Please Create a new Planar Displacement Constraint in Creo Simulate FEA that may be applied to a surface of a component to allow additional movement off plane in the positive direction but provides contact pressures/forces in the negative direction. Imagine trying to setup an analysis of the structure of a complete engine and using simplified reps to isolate various portions to verify the constraints, loads, and load paths are set up properly. It would be very helpful having this new Planar Displacement Constraint with lift off in Creo Simulate FEA to allow you to run an analysis of the head assembly without the block in order to shake out the simulation setup. This would allow you to simulate the block being in the assembly to some extent and its contact pressures. Granted you can use a spring with different stiffness in both directions to do this today. Thanks, Don Anderson
Are assemblies are 10s of thousands of components and many indentures deep. Default explode status is "exploded" for all... which is quite useless (should be "unexploded"). Anyway, there is not good way to keep the explodes states of newly added components (at any indenture) cleaned-up. Need to be able to select "ctrl F" and then get a list of all components whose explode status=unexploded (or exploded)... so that only those can get toggled.
Hi PTC, Please add the ability to Creo Simulate to allow Idealizations like springs, rigid links to be tied to Idealization sets (groups) so they can be turned on and off from the Analysis Definition Dialog box just like Loads and Contacts can be. This would allow one to work more efficiently in large assemblies while using simplified reps to isolate components and turn on needed constraints and off not needed constraints. Thanks, Don Anderson
When the "envelope rep" of an assembly is active and a user goes to the "model properties" menus to view mass properties, those mass properties properly reflect those of all the components the envelope part was defined to represent. HOWEVER, if I run mass properties analysis... the envelope "becomes a normal" part and shows ITS volume times density as the mass and CG location! that degrades the utility of envelopes to being strictly visual in any and all higher assemblies! The mass properties of envelope parts should be "full-assigned" and driven by the components they represent. Below are two very common (for many customers) use cases: Case 1: The actual assembly (that defines the envelope) is used higher assemblies. If my rocket has 200 fully-detailed electronic box assemblies assembled to it, most users and most daily purposes are properly accommodated by retrieving a higher level assembly rep that shows the envelopes of all boxes. Each one being simple "boxes" represe
We constantly struggle with trying to find features on our model via the model tree. All too often the features (holes, cuts, etc) are very small compared to the part or assembly size... so even though it is "being highlighted" somewhere on our screen... there is no practical way to find it. When working with the model tree, would love to see a right-mouse button option called something like "beacon highlight" or "small geometry highlight" may be clearer. When selected the system would generate a repeating sequence of expanding circles/curves start with just large enough to circle the requested geometry in the current view and then expanding outwards across the screen like ripples in water when a stone is thrown in. this way, even if the requested geometry is currently "outside the edge of the users monitor" the would see what side of the monitor the ripples are coming from.
I opened a case (and SPR, Article) in the support site because I have some cases of drawings with differences if in Creo Parametric 3.0 or if exported in dwg and opened with Autocad or Creo View. Creo parametric: Autocad: Creo view Ptc answered: Works to product specification for Creo Parametric 3.0. Creo DXF export/Import uses the AutoCAD libraries and the exported DXF file is showing line type as Centerline with Scale 1 In AutoCAD. Creo view will behaves same as AutoCAD. To request a change in the functionality, refer to Product Ideas @ PTC Community
Hello,Currently there is a limitations for LDA (Large deformation static analysis) for rotating parts as: "rotations at weighted links and advanced rigid links must stay small, since rotations are treated for those like in SDA " even when LDA is calculatedthis limits the scope of simulations that can be simulated with LDA and/or finit friction (finite-sliding).i think it would be worth looking in to this limitation for a new update of Creo Simulate.BrAhmad Al-Kerdi
Add the posibility to hide all parts except the ones selected and after doing an action on the selected parts (for instance creating a feature in one of the parts), return to the previous shown parts.This improves working speed and working ease.
Make it possible that 2 or more positions of parts in the assembly can be shown in the same view (for instance the open and closed position of a door in a Cabinet or the extended and retracted position of a Hydraulic cilinder). The appearance of both Positions should be chooseable (for instance the first position as shaded and the second position as dashed line or transparant) Often you want to show both end positions of a movable part (for example a hydraulic cylinders) and add dimension to it on the drawing (retracted position and extended position of the cylinder, rotation angle of a certain movable part (open and closed position of a cabinet door) etc.) In Assembly mode: - Add a "Position" tab in the View Manager instead of using the current working method by using the snapshot feature in assembly mode - Update it automatically when for example a new part is assembled, an appearance of a part is changed or the simplified rep is updated - Make the "Position"- state ava
There should be a way to switch off the Creo 4.0 double-byte support in filenames and features through a config-option.Users might be tempted to use unwanted characters. An administrator should be able to prevent this by a config-option - like: "enable_double_bite YES*/NO"
Does the Creo 4.0 View Adapter able to convert Part and Assemblies in 3D PDF ?If it is not the case, do you know if it is planned to implement this feature soon ?Regards.
Sind in der modelltree.cfg Modellbaumspalten definiert, sind diese per default immer eingeblendet.Sind viele Spalten definiert, wird der Modellbaum sehr groß und verkleinert den Arbeitsbereich.Nützlich ist eine config.pro Option, die das als Voreinstellung regelt.MfGKapfer
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.