Recently active
helloHave the ability to adjust the width of the first column with a default value
In an annotation view it is possible to make all hidden lines either visible or invisible.However, it is currently not possible to make all the hidden lines that are not within a cutaway visible and at the same time all the hidden lines that are within a cutaway invisible.Workarounds:- individually make unwanted hidden lines invisible- make a separate partial view covering the area of the cutaway and define all hidden lines to be invisible in this view
'Gradient Background' color setting has no effect on the Preview in File->Open, i.e. background color of the preview gets its defaults from the syscol.scl file or system_background_color option in config.pro, BUT it is not possible to set the background as blended Gradient.In Wildfire versions of Pro/E (like Wildfire 5.0) the Gradient Background option controlled both - The main Graphic Window + the Preview Window,but in CREO 3.0 the Gradient Background option controls only the Graphic Window.Most of Pro/E users that I know prefer drafting drawings with a black background.Setting this Black background option, undesirably affects the background of the PREVIEW window - to be BLACK!It is most needed to have the Gradient Background color setting to control also the PREVIEW Window!
The Question is: How to control the length of the centreline for half section in Pro/ENGINEER, Creo Elements/Pro and Creo Parametric New drawing setup option half_section_line allows to set centreline but its length cannot be changedHow to control the length of the centreline for a half section view?Possible workaround to extend the display is to show or create a centreline and move its drag handles as desired
We often have a need to dimension a drawing with both US/Imperial and Metric dimensions. We don't want "dual" dimensions but rather the ability to display a particular dimension in a different unit than the rest of the drawing. As stated in a similar request, it is relatively common to need a metric sized or threaded hole or other features in a normally English dimensioned drawing.
Upgrade support .ai import file version from 7.0 to 15.07.0 is a little old no ?
It is possible to wrap a spline curve that is on a work plane onto a cylindrical surface using the function "Wrap on Surf".However, it is currently not possible to go the other way and to wrap a spline curve that lies on a cylindrical surface back onto a work plane.This should be made possible.Workaround: None found. Attempts to use sheet metal functions were unsuccessful.
Trace curve created with MDX analysis need to be updated When we create an analysis and a trace curve, we can’t update the curve trace. The trace curve need to be automatically updated
The acceptable type of elements for the cam cannot be a curved surface. However, this function is very used to simulate an abutment
For curves selection in CAM definition, it is not possible to use an intelligent selection (tangent, from surface,…) It’s necessary to select curves one by one with CTRL.
Have a timescale similar to Pro / animation in which we would find : -time of an analysis -motors -…
Actually it is not possible to activate in the same time "Auto Cutline" and "Tool center curve"This would be very useful to machine closed pocket to:- start at the center of the pockect using the point- avoid retract on the contour of the pocket thanks to the "tool center curve"Actually the solution is not to select "Auto cutline " and to create a projected curve instead which is more work to do
1. Add ability to select a part or assembly feature while in Creo Parametric Simulate and edit it's definition. It's very time consumming to edit feature definitions on parts which were not created by you just so you can get it to mesh. 3. Add ability to select feature in model and have it highlight the feature or rightt click and go to that feature in the model tree while in Creo Parametric Simulate. 2. Add ability to mesh D1 x D2 conic round with values 0.5 for sharpness "0 thru 29" for distance one 40 for distance two where the round transitions the inside corner of a rib going into a round boss. 3. Give more detailed description of errors while meshing... "Problems were encountered while preprocessing the features for the highlighed surface. Source AutoGEM" Sometimes the the feature not highlighted and when it is where on the surface that is highlighted is the issue. The whole surface or on
With the selection filter set to "geometry," user should be able to select a visible surface by clicking on it, even if there is an edge hidden behind the surface under the cursor. Current functionality is to select edges whenever possible, regardless of how many surfaces are in front of that edge. The edge could be completely hidden from view, behind a huge surface that fills the screen, but if it is under the cursor, it will be selected instead of the surface. This current selection functionality could be enhanced by prioritizing selection by z-depth, where the geometry closest to the screen is selected, since this is what users typically expect.
With the old Drawing note system, a mapkey can use the EDIT > PROPERTIES command to edit a note. However, with the new Creo 3 system, the only way to go back into a note is to click on it. That action can not be reproduced with a mapkey. Therefore, any changes to a note can not be done (unless you try running trail files).
When creating a cure through points in IDD you do not have the ability to define tangent end conditions as you are in Creo Parametric.Can we add the ability to define tangent end conditions to curves created in IDD?Creating A Curve Through Points In IDDCreating A Curve Through Points In Creo Parametric Modeling
Our config setting uses one of the old blue schemes for the background in Creo 3. However, this drowns out the blue that is used to highlight overlapping geometry in the Flat Pattern Preview in the sheetmetal module. It would be great if we can customize this color without changing the background.
Creo simulate, pro/mechanica structure, it's alway been the case that when you define a fringe or contour result window, the legend levels are defined automatically.When you're doing a project, with the umpteenth variation of your subject, you know that you always want to use a typical range. Still the only way is to generate the fringe plot and edit the levels afterwards, after which simulate regenerates the window, which takes time.Especially in animatred fringes, with many frames,. regenerating the animation takes an enormous amount of time.In creo 3.0 this happens twice, once for the maximum level value after editing, once for the minimum level. Please provide the option to define the legend levels in the definition window.
File location parameter for showing file location path in drawing.
Ability to create parameter assocciated to dimension.It could be usefull in the MBD, to stroe complementary information as for exemple:ppm target for the dimension (or Cpk and cc)Result of the measurementStack up result analysis.Robustness class of the dimension.
The display of the structure of the "Model Manager" I want to switch in accordance with the "Load Rule". When used in "ModelManager" of "Load Rule" the "Heighest Revisions", display of the current situation does not match.
Implementation of config.pro "UI_THEME" in Creo Parametric for better visibility of pushed icons and position of scroll bars
It would be nice if the default "Creo Files" filter could be modified or if a "User Defined" default filter could be defined. I work with stp files a lot and it would be nice not to have to change the file type filter all the time and instead just add it to the list of "Creo Files" which is the default.I can imagine that people that work a lot with autocad files might like the same thing for .dwg files for instance.
Dear Sir,Recently my customer has come across the below small requirement.1. The file path should be printed automatically on the drawing, once he add the parameter in template.Since this facility is manual at this moment. Please add this as a parameter in the template for automation of this small.Best RegardsAnil Pagar
Currently Windchill is unable to delete a selected group of objects if one of those objects is found to be in a workspace or tied to some process or connected to any hierarchy. If an object in the list is found to be in a workspace, selecting the "medicine box" in the event manager will not necessarily resolve the issue because the same object could be tied to something else within Windchill. There should be a way for Windchill to delete all of the selected items that are free and clear of any relationships or processes instead of not deleting anything in the selected set of objects due to one or more being tied to something else.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.