Recently active
I am using Creo Parametric Release 10.0 and Datecode10.0.4.0In Creo 7.0 I was able to list the PTC_REPORTED_MATERIAL parameter as column inside the model tree.In Creo 10.0 the PTC_REPORTD_MATERIAL is not shown anymore. Instead there is always List (in German Liste) displayed. Is there a way to display the active material of the model inside the model tree again?Here are the errors that I facedno error or warnin - the parameter PTC_REPORTED_MATERIAL is not displayed as expected.
I am using Creo Parametric Release 10.0 and Datecode10.0.2.0Creo 10.0.2.0 Supports the import/unite of SolidWorks 2023 data.When do you plan to support SolidWorks 2024?This is a major Roadblock for our Creo 10 update with important new functions.CS134024 only shows SolidWorks2023 from Creo 10.0.2.0Thank you for your feedback and support.
I am moving my files from one computer to the other. I copied the files from a computer using Creo Parametric 10 to a computer using Creo Parametric 9. I am unable to open any of the files, even though the association with Creo seems to be valid. The files show up as .prt or .asm, as they should and they have the proper icon. But I can open any of them, even simple beam element .prt files. So I'm assuming that there's a reason copied files don't work this way. Is there something different in the setups between the two machines that I should take a look at? p.s. I'm assuming this question belongs in System Administration, but I'm not sure.
Hello everyone,I am currently using Creo 9.0 to explore the effects of corrosion on bolted joints, particularly in relation to Tightening Torque and Initial Load. My plan is to start by analyzing a standard bolted joint to understand its behavior under typical conditions. Afterwards, I intend to modify the material properties to simulate corrosion and perform the analysis again to observe any correlations.Could anyone provide insights or resources on studying corrosion's impact on these factors? I've struggled to find relevant information on this topic.Thank you for any suggestions you might have!
I have successfully used a specifically sized flat Equation curve in my die designs. I have on a number of occasions however needed to use the same radius and spacing around a rotation which to this point have been very fudgy.Below is the equation that I have been using.This results in a curve like the following.Would it be possible to make an equation curve to the below shape? The spacing would be the same as with the top example but I would somehow need to be able to define a center or slope. Can this be done?
status = ProBrowserAuthenticate(username, password); status = ProServersCollect(&aliases); status = ProArraySizeGet(aliases, &num_servers); for (i = 0; i < num_servers; i++) { status = ProServerUnregister(aliases[i]); } ProPath serv; ProStringToWstring(serv, (char*)workspace.c_str()); ProPath URL; ProStringToWstring(URL, (char*)serverurlw3.c_str()); ProName wsName; ProStringToWstring(wsName, (char*)wsNamestr.c_str()); status = ProServerRegister(serv, URL, wsName, &aliased_url); status = ProServerActivate(serv); ProPath* p_file_name_array; ProPath* p_subdir_name_array; //string da = ".asm,.prt,*.drw"; string da = "*.drw"; ProName namme; ProStringToWstring(namme, (char*)da.c_str()); status = ProArrayAlloc(0, sizeof(ProPath), 1, (ProArray*)&p_file_name_array); status = ProArrayAlloc(0, sizeof(ProPath), 1, (ProArray*)&p_
Hello all i do have some Problems questions in understanding Sensitivity Analyses and Cordinate Systems What i have is the Default CYS and an Offset CYS that i create i control its Origin with Paramets as followsX=200Y=200Z=-200 the relations i use look like this :$d3=X$d4=Y$d5=Z when i now start and run an sensitivity Analyses for Parameter Z with a minimum Range of -220 and maximum of -180 it runs though. but when i recheck my Parameter for Z it has changed from-200 to +200 and the Coordinate has flipped its Position. is it possible to avoid flipping Parameters or Dimensions i don't want the minus to disappear? can someone relate and help out?Kind RegardsMarkus
I saw this post from the recent Creo Illustrate training at Blue Origin this week - sounds like it was a great event! https://www.linkedin.com/feed/update/urn:li:activity:7196656920093425665 Next up for Jeff Coon and the Creo Illustrate team - a webinar on May 29th! Technical Illustrations for Service: How Tech Pubs and Tech Illustrators Bridge Complexities in Communication Imagine being able to take complex engineering designs and turn them into easy-to-understand visuals - making the intricate simplicity itself, perfect for manuals, assembly instructions, and more. With Creo Illustrate, you can create illustrations that not only look good but also communicate effectively. Creo Illustrate is a powerful tool that transforms 2D and 3D CAD data into engaging visual illustrations and animations that manufacturing and service teams rely on to get products out the door faster. Enhance Visual Communication: Utiliz
Hi All, I am looking forward to do a modal analysis of two disks connected with a spring. so could you please advise is there any way to use spring command ? If so how to define it properly? I would appreciate your help with it.
I'm trying to create a spring in "Mechanism". What I did was I created two simple components in an assembly, and when the assembly is activated, I clicked Applications->Mechanism, and then a couple of options including "spring" are greyed out. in "insert" ribbon, only "servo motors" is available to select. All items in "properties and conditions" ribbon are greyed out. There is no "spring" option under mechanism tree. I'm using Creo 9.0 Parametric. Can someone help? Thanks!
I need to mill 32 identical objects from a sheet of aluminum. Operation includes drilling, countersinking, pocket milling and profiling of each part. I've got the first instance set up in manufacutring and now I want to copy it into a 4x8 array such that all of the holes will be drilled, then all the countersinking, then the pocketing andf finally the profiling. I'm sure I've done this, but cannot remember how.
I have a flexible torsion spring modelled.I have an angular dimension annotation calling out the angle between the legs. When the spring is in the free state the legs are parallel and therefore @ 0° and the dimension annotation fails, and so does the model.When the spring is shown in the deflected state @42°, the dimension annotation is shown and the model is happy. See below As the spring will be saved in the free state, how do I prevent the annotation / model from failing. I do not want a separate family table member, combined state, simplified rep etc. I just want the base model to have the annotation without the failure in the free state. Any ideas?, Thanks.
When duplicating a model along with its drawing, I encounter a warning after modifying the part, indicating a duplicate label on the drawing. However, despite searching, I cannot locate the label named "A." Interestingly, the system allows me to add "A," but it appears with a line below it. This suggests that the original "A" may have lost its reference and is not visible on the drawing. Additionally, I cannot find it in the model tree to delete it. How can I resolve this issue or identify the location of the duplicate label?
"In memoriam of Professor Ivo Babuška (* 22 March 1926 – † 12 April 2023), a Czech-Americanmathematician, one of the most important developers of the p-method of Creo Simulate."
Hello, i am looking for this programm Pro/ENGINEER Release 2001 Datecode 2005030 2001.0 For Windows 10-11 and 64bit. Can somebody help me how i get this software? Thank you! King regards
I'm looking for some documentation on how to install Creo 8 with Corretto (JRE 11 ). I've searched the PTC website but I'm not finding it. I'm looking for installaing a new setup, as well as converting an existing setup to not use Java, and use Corretto ( JRE 11 ). If you can point me to a document I'll be happy to read and try it out. Anyone able to help point me in the right direction. Any help would be greatly appreciated. Thanks.
I don't even know what it is called to try and search for.But I want to be able to show what the orientation is set to when in a combination state.
Is it possible to modify the size and location of the the parts list table when saving as a pdf? What is common practice around using Illustrate figures for 2D parts manual documentation with parts lists? I tried editing the XML but with the little guidance out there, I couldn't even replace the ptc logo with my own. A little frustrating this functionality isnt easier to use or doesn't exist. Maybe Creo Illustrate is not intended to make 2D manuals? I'm just a Cad Admin and this software was purchased before I was hired so I dont really know anything about it
Hi everyone,I was generating the DWG file from a drawing. Some views have the state "Shading With Edges" in the "View Display" properties. This is due to production porpuses and I cannot modifiy their representation.During the saving operation, Creo displays a warning in the console, I attach the image below.The resulting DWG file is incomplete, the biggest shaded views are missing on the drawing.I tried changing some export settings, but nothing helped. Even exporting in DXF format resulted in an incomplete drawing, while PDF is ok.Does anyone know how to solve this problem?Thanks in advance.
Hello, Is it possible to use Creo Generative Extension for purpose of generating multiple design variants of same parametric model with dimension variations?
We successfully installed Creo 10.0.4.0 on Azure NC4as_T4_v3, and Ansys simulation is now working. We found new issues: In the CSL fluid study, clicking on the Streamline baton causes Creo to crash. Graphical errors in basic Ansys simulation results. In the advanced results, it works properly, with no graphics issues.
hello everybody,can you tell me why if I open a file it retrieves thousand of other files in Workspace?it appears no external references to methanks
Hello everyone:I have the following issue with my bearing: In the sectional views, the balls always seem to be fully displayed, and I just can't get rid of it (as in the attached file).I imported and installed the bearing from the SKF catalog as an STP file like all the other bearings and they word fine. Please help!
I have a sketch of a quadrilateral between 2 parts in my assembly and the dimensions of this quadrilateral are derived from the spacing between the parts (by putting constraint "Point on Entity"). Now, I want to establish relations for placement of another part with the dimensions of this quadrilateral. However, when I enter into the relations dialogue box and click on the sketch, the dimensions corresponding to the lengths of the quadrilateral do not show up. I understand that this is happening because it was not a defined length, but rather a derived length. But is there a way to access such dimensions in the relations dialogue box?
Hi everyone,since I need to get screws based on threaded holes, is there any chance to set screw diameter by thread surface diameter or to set DG dimension on drilled hole surface?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.