Recently active
I like the attached pdf instructions. Have you ever seen a real gear like this? If so, in what application? Do you have some real photos of this type of gear? I tried to find an oval gear using Google.
If the model is symmetrical, you can make it with just 1/4 of the geometry, then mirror as shown below.
I know this discussion has already been answered, but I was just curious on the imported feature. Are you supposed to have two different diameters as shown below? If they are supposed to be the same diameter, you don't need to make the entire model, rather, use symmetry, either make 1/2 or 1/4 of the model.
I think one functionality that was added since WF4 is Freestyle. You can make some very complex surface shapes with this tool, as I cannot find this in WF4. See below image. This is not the same as Free Form Surfacing or Surfacing tools. I had Surfacing and Free Form Surfacing classes in WF5.
No. This is not possible. Please see the below response from PTC.
What software are you using?
Online web-based spring analysis calculator for fatigue:http://www.amesweb.info/MechanicalSprings/CompressionSpringFatigueDesign.aspx
Does this resolve the problem?
The first thing I noticed is that I cannot merge the surfaces. This will take some time to investigate.
You will have to make it like I showed you in WF5 or upgrade to Creo Parametric 2.0.
You can still add datums to the mirrored part. After you make the mirror part, open it and the save it with a new name. Now open it again, and you can add datums.
That's right, because you're selecting Geometry Only, and that's all you will get. If you want csys, datums, features, etc, you have to select Mirror with Features. You're original concern was that the model tree was empty after the mirror was made.
Here's how you can make a mirror part in WF5:1. Make the assy and assemble your source part 2. Select "Component Create" and "part" as the type, "mirror" as the Sub-type 3. In the "Mirror Part" dialog, select the mirror type and uncheck "Placement Dependent" to avoid making the mirrored part a child of the assy. 4. Pick the part you want to mirror 5. Pick a plane to mirror about. If you pick a plane in the target part itself then the new mirrored part will not be a child of the assy and the assy will not be needed to keep it up to date. 6. Select OK to create the part 7. Open the mirrored part and save it. 8. Discard the temp assy.Please see the images below on how to make a mirror part:After this last figure, you can open the mirrored part and save it with a different name. Hope this helps.
SPR 2224439 has been implemented to correct the Max Distance measure where points can be created. This should be corrected in the next release M120.https://www.ptc.com/appserver/cs/view/spr.jsp?n=2224439
If you want to merge the surfaces:Selected the first quiltHold the CTRL key down and select all the other quilts. Select the Merge function, then select ok.Thicken the surface.
Hi Joseph,Are you talking about Save > As > Mirror as shown in the below images? It will create a csys after the mirror is performed. If you want features, select "Mirror geometry with features" and it will create a model tree in your mirrored part with a csys.
Yuichi,They way I made the points in the attached example is that I perfomed a Save As Analysis, and this marks the curves where the points are to be created. I then created the datum points by sketch, using the curves as references. I already knew the max distance from the measure tool, then I just measured the points to make sure it was the same as the previous measure.This is supposed to be fixed in the next Date Code M120.
Hi Yuichi,PTC stated that this is a bug in the software, and SPR 2224439 has been implemented to correct this. Tech Support stated that this should be fixed on the next Date Code M120, hopefully. I attached the link for your review.https://www.ptc.com/appserver/cs/view/spr.jsp?n=2224439Also, I posted two emails from PTC Support where I reported this and PTCs response.
You stated:"After migration to PRO-E , for the same sheet metal component , after inputting the same k-factor value , we have a difference in the flat state value of the sheet metal component."What is the difference in the flat state value?
The attached file has the max distance between two points, 996.472-in.
Hi Timothy,Please take a look at the below image and see if this is what you're trying to make. I attached the file for educational purposes, because the sketch profile is not exactly the same, but you can get some ideas for it. I made it with a helical sweep cut.
Here's some images of the file you uploaded. Are you attempting to make datum points on the curves for maximum distance?Figure 1: ISO ViewFigure 2: Top View
Thanks for uploading the file, but I haven't provided an answer. You may want to uncheck "correct answer" for me.
If you're new to Creo 2.0, you may want to watch the attached video (58 minutes).http://www.ptc.com/product/creo/upgrade-resource-center/video/ptc-creo-2-0-demonstration.htm
Can you upload the file?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.