Recently active
Richard, Can you upload the model? If so, use advanced editor. Welcome to the forum.
You upload it under a new discussion, not Product Idea, as shown below:
Charlie,If you sweep just an ellipse, which has a defined cross-section, along a single curve in one plane, you will get something similar as shown below (ellipse surface). Try making a sweeping ellipse with just one trajectory. This is probably not exactly what you're looking for, but just try it as self-training for a single sweep. Sketcher has a built-in ellipse feature as shown below.
The spreadsheet will calculate it for you. All you have to do is enter the values. Very simple. It may have to be your reality if PTC doesn't accept your Product Idea.
In the design process, one should be able to calculate all masses in a spreadsheet before simulation, and then the simulation will verify if it was predetermined correctly.I've had to do this many times when simulating gravity loads.
You can certainly add extrusions to a STEP import after setting up the datum planes (if datum planes were not save in STEP output). So if you want to add a piece, just add it with any type of extrude tools you need.You can also modify a STEP import with the Flexible Modeling Extension (if you have it).
The purpose of having Idealizations in Creo Simulate is to reduce run times. By adding Idealizations in Creo Simulate, you have increased the amount of mass from 1.566 kg to 4.682 kg. What was the purpose in comparing the mass in Creo Parametric vs Creo Simulate as shown below?
Doug,Are the failed components in your working directory?
Well...it's probably easier to draw than to fabricate.
How are you going to get an endmill tool to cut a sharp v?
Doug,RMB on the failed part and open it. What do you see in the model tree of the opened part?
James,Look at the attached post and scroll down towards the bottom and see my solution with three figures and the attached file. See if this will help you.http://communities.ptc.com/message/237605#237605
If you're on maintenance with PTC, upgrade to Creo Simulate 3.0. It will be worth it.
You have to map to where the tree.cfg is located after the mdl_tree_cfg_file option has been added. If you don't, the settings won't work. See attached image.
Can we see the reflection analysis on the Solidworks fill?
Was your question answered?
Andreas,This is the second post you have on the same subject. The link below is for the same problem:http://communities.ptc.com/message/259957#259957
Without the model, it's difficult to determine the problem. Can you upload the model? I'm sure there will be several people that will assist you, including me. I will be back in my office on Monday, and there are a lot of Simulate users in this Community that will see your post.
Antonius,Do you think it will work using this method from the Learning Exchange?http://learningexchange.ptc.com/tutorial/3465/creating-a-parting-surface-using-fill-loopsI don't have the Mold extension.
Good to know...thanks.
When I import the STEP file and launch the Style function, I can't create anything (maybe because of STEP). All functions are grayed out. Interesting. Yes, I have ISDX, so I know it's not a license problem.
Are you refering to Freeform Surfacing (as shown below)?
Are you refering to the Fill command as shown below? If so, that's to create a flat surface.
You have to have the Mold Module in order to use this. Correct?
If you have upgraded to Creo 3.0, you won’t be able to use the installed Help Center unless you have at least Internet Explorer 9 or later (and Mozilla Firefox 10.0.1 or later). If you work for a company which has only IE 8, the installed Help Center will be useless, and there is no work-around for it (PTC Case #12210658). Creo 3.0 Help Center defaults to using your internet browser as the GUI. I like the Creo 2.0 Help Center, as it won’t default to using a browser. So if you have Creo 2.0 Help installed, and you want to upgrade to 3.0, and your company browser is prior to the ones mentioned above, keep the Creo 2.0 Help Center installed, as you can still use it for a lot of things in Creo 3.0. I’m posting this because we use IE 8, and I can’t use the Creo 3.0 Help files. Thanks PTC.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.