Recently active
Do you not have ISDX with your Creo application?
Dan,When I first responded, I didn't make it very clear. Sorry. I have now provided you with the instructions on how to do it. Hope this helps.
Dan,I talked with a top contact in PTC today about this, and I forwarded your Product Idea to him, since it has some nice screenshots, and requested instructions on how to do this with a UDF. I also furnished this post.
Dean,I read some articles yesterday where ICEM could be used with CATIA, ANSYS, NX (formerly UG), etc., and I saw that ICEM Ltd, UK, was an independent software not developed by Dassault, but Dassault acquired it in 2007. So when you made the statement, "Software like ICEM and CATIA", I don't know where you're coming from. Isn't ICEM now part of Dassault? Anyway, I really enjoyed your response, but I was looking more for something on the visual rather than verbal. And I didn't comprehend why you stated PTC will never have a Class A software. Is is that you're predicting that the developers at PTC will never have the knowledge, skills, and abilities to compete with CATIA for Class A surfacing?
Dean,Can you provide an example of high degree "verifiable" surface work that Creo cannot do, as you stated in your post?
Avinash,Could you be more specific? Are you talking about leaf springs that are used in the automotive industry or some other type?
Luis,You can see down inside the elements by shrinking them as shown below, although this is not the same as slicing.
Luis,Also, you have to be a customer on maintenance to submit an idea.
Luis,If you want to submit a Product Idea, just go to the top of this discussion and click on PTC Creo and it will direct you to the below image. Then select Product Idea in the right hand side of the web page. Are you wanting to submit the idea for two or more components in fatigue?
Luis,Fatigue Advisor, Creo Simulation’s module for fatigue analysis, is optimized to obtain a rapid indication of whether a design is sensitive to fatigue without having to provide the full range of input normally required to solve this type of problem. The solver technology integrated with Creo Simulation’s Fatigue Advisor is nCode International. The physical nature of fatigue was not widely understood during the early days. August Wöhler therefore took a more pragmatic view of fatigue analysis. The method he developed later became known as nominal stress (or S-N) fatigue analysis. This did not differentiate between the Stage I (crack initiation phase) and Stage II (crack growth phase) growth methods and instead related the nominal stress range to the time taken to complete failure. Though S-N analysis is still widely used in test-based fatigue analysis, it has one major drawback for computer aided engineering (CAE) applications. Fatigue initiation
Luis,If you want to see elements down inside a component, all you have to do is shink the elements to the desired size.
Don,I'm not sure. I know I haven't. The solver behind Fatigue Advisor is nCode International. So if a Product Idea was submittted, I think PTC would have to work with nCode to implement it. But that's my thinking.
That's nice, but which software are you claiming is the best. Are you stating Creo Parametric is the best?
If you're running a mult-body contact analysis in Creo, and if you're trying to run Fatigue Advisor in Creo, then this will not work. Fatigue Advisor can only be used on a single component.
Can you make this a question for discussion?
In the pre-processing phase, no. In the post-processing phase, yes.
Will Creo Simulate perform the following analyses on a rotor turbine? 1. In order to perform a dynamic frequency, a modal analysis must be performed first. 2. After the modal analysis, spin the model at 96000 rpm for 1 minute at 75 degrees F. 3. View the stresses. Currently, PTC technical support has not been able to answer this, as the case number 11575905 was started on Sept 5, 2013. The online knowledge base has only one example, which doesn't fully address the problem at hand. Any comments/solutions are welcomed.
Dan,I made a comment on your Product Idea, and I voted on it too.
Rajiv,What software version are you using?
I liked your answer anyway, regardless of the post date. Thanks for the input.
Dan,Creo has a function called UDF (User Defined Feature), and I'm going to contact one of the developers for assistance and see if we can get this programmed to do what you want. I submitted a Product Idea for PTC to add Plane By Equation back on 11/7/12, as NX and CATIA have this functionality out-of-the-box. Creo will also do it, but with a UDF, which can be a very powerful tool if you're good at code writing. The sad thing of it all is that PTC is still sitting on my idea, and it's been almost three years. It's something so simple for developers it could have been added between date codes years ago. I'm all for your product idea. I'm always in support of ideas that other software have, but don't be surprised if PTC doesn't even acknowledge it. I've attached my idea for the plane by equation.Creo Parametric 3.0 Plane by Equation Ax + By + Cz + D = 0
Luis,I've attached an image of a meshed body in an assembly, but Mats has already demonstrated this, but you want to hide all the other components.
Luis,I think I understand that you're concerned about viewing meshed bodies in the pre-processing phase, not the post-processing. The previous link that I provided was only for post-processing, as you can see each meshed body and even cut those meshed bodies to view stress results or whatever results you have pre-determined.I think Mats gave you the best explaination. This is on my list of Product Ideas, to have the same meshing capabilities in Creo Simulate as they do in StressCheck. StressCheck will do exactly what you're asking for, because each body in StressCheck has it's own independent mesh record before even assigning material properties. You just select the desired mesh record (or elements sets as they call it) and that's what you will see in the GUI, the desired meshed body.However, if you're concerned about the meshed body being invalid, Creo will give you a report (diagnostic tool) that will show you the troubled elements, if any, during the automesh
When applying cosmetic lines for exploded views, you can only selet two references. In the below image, there are three colored lines drawn over the existing cosmetic lines, as it took three cosmetic lines to show the fastener path through two components. This means the collector for each thread had to be launched three seperate times. To improve the speed in creating cosmetic lines through multiple components in an assembly, add the capability to collect more than two references in the same Cosmetic Offset Line window.
Hi Luis, You can plot any component from an assembly, as detailed in the attached post: Can you hide components of an assembly in a Creo S... - PTC Community Welcome to the forum.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.