Recently active
Taking a measurement just beyond the split confirms that the profile is moving outward.
Perhaps. But when I set up the attached measurements, the distances are the same, so the profile has not moved outward at this point. Maybe this is the point of tangency where it starts to move out. I will do another measurement just beyond PNT0.
The geometry in a particular area is not suited for meshing.
That's true, but I was referring to system colors under the drawing format tab. You're referring to the image on the left, and I'm referring to the image on the right.
I'm not using pentable. Is that the only option to get GD&T to export in color?
Community,After exporting a drawing to PDF, there is no color in the PDF except for datum axis and csys, they are the default brown. But all of the blue text and blue dimension lines, etc., show up in black. I saw a post where people set up the pentable for actual printing on paper, so I'm wondering does that apply to PDF too? And this happens after I select "Color" on the export settings. I'm using Creo 3.0 M010. Any solutions for this? Thanks in advance.
Thank for tips. I was able to change any of the text to a desired color except the GD&T and datum reference symbol. I can change the datum reference symbol color in the model, but not in the drawing. The image below is from the exported pdf with the items that remain black boxed in red.
To change the color.
Tom,I selected the green in the systems color, and it printed out green, as shown below.
Excellent video! Thanks for posting.
Carl,12.03 in is 305.562 mm, so the reader is inches.
Tom,In order for the text (and dimension lines) to show up in color in the PDF export, I selected standard colors and not system colors in the Format tab. The image in the lower right is a snippet from a PDF export and shows the .125 in blue and the 100.0° in black, because I changed the .125 to a standard color (I didn't try other system colors). Now, I have to figure out how to keep the standard color configuration turned on so I don't have to select this every time I make an annotation.
Tom,Thanks for the input. For the below drawing, it appears the only thing that will print in color are datums (axis). Even the blue dimension lines, GD&T symbols, and datum symbols all print in black. I used the same settings for the PDF export, selected Color and unchecked pentable.
My 2-cents worth probably won't help, but I've never had any problems opening prior .prt files from any version going back to V18, and I'm on Creo 3 now. On-the-other-hand, all of these prior models I built, not obtained from another source.
Marc,This can be controlled with a config option. Go to your configuration editor and add measure_dec_places and enter a value of 2.
You want to simulate the deflection of the hinge, and not the stress? It appears the hinge consists of two bronze colored components, fasteners (2 or 4), and the two ligaments that are part of the door. I cannot distinguish if the fasteners go through the entire assembly, or if they stop within the bronze plate. It would be nice if you could show a cross-section of the hinge with the fasteners. Is there a particular area of the hinge that would be the region of interest? That would certainly narrow it down. Do you want deflection results display as a fringe plot, or a graph?
Good point. Sounds like a discrepancy in the code.
Based upon your crashes, I'm wondering what kind of hardware you're running, especially the graphics? You should not be having a crash by showing a datum on a drawing.
Are you trying to make letters with the sketching tool or are you trying to make them in drawing mode?
I don't draw schematics, but try different font settings in the PDF Export Settings. The "Stroke Non TrueType Fonts" is activated with a config option.
If your company will issue reprimands for using the mirror feature, and if it's a written internal policy, then I would not use it. It's hard to believe a company would lower itself to such a standard as that. The mirror tool is a great feature to have, especially for manufacturing right-hand (RH) and left-hand (LH) aircraft components. Many times I have received a LH component, the RH needs to be manufactured. You bet I'm going to use the mirror tool, instead of trying to re-create all that geometry.If you're very proficient in mirroring, perhaps you could make a presentation on some of the models and show a cost-savings to management. Maybe they will allow mirroring, after all, they want to see savings ($$$$$). Right?
I do not have a student version of Creo, but Creo Parametric comes with Creo Simulate Lite at no extra charge, and I think this is what comes with the student version. This found under the model setup (commercial version). Once you select OK, the process guide will activate. If you have a student version, there is an academic support group in the community.
Could you mark his response as correct? Thanks.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.