Recently active
With the introduction of Creo Simulate, I've not been able to locate the functionality where you can insert .rwd files without having to use a template. You can do this with WF5, WF4, etc. Does anyone know how to insert a .rwd file in Creo Simulate 3.0?
I made a couple of posts under the Analysis and Simulation group, but my post doesn't show up at the top on the main page. Why not?
Eric,You cannot insert a saved results window, but I kept playing around with Creo 3, and you can Copy a result window and it will put it in the results window while keeping the original. Then you can use the pull-down menu to change reults or the edit key (looks like a pencil) to make graphs. Because the pull-down menu doesn't have Measure by default. I've attached a couple of screenshots. FYI.
Mark,Are you importing an IGES cross-section drawing or IGES solid model? Also, can you upload a screen shot of the imported IGES file that's showing the cross-section?
This link is a post I made this morning:https://www.ptcusercommunity.com/thread/59938?sr=inboxAnd it should appear on this page and the PTC Creo page, but it doesn't show up on either one of them.
Add the capability to control the shading in the results window. Currently, the results windows has "on or off" for shading. Shading can be too dark, and non-shading can be too bright. Make the shading function variable with different controls such as brightness, contrast, etc. The figure below shows the only two options. The image on the right is with shading turned on.
Add the functionality to allow two driving curves for round creation.
John,I made a tube and fixed at one end just to show that Simulate will deform properly under a pressure load
This problem needs to be addressed by Mark Fisher, because is the Product Manager for Simulate.
Fastener preloads are updated if you select Account for Stiffness. With Creo 2, and all the way back to WF4, we had to make one run, take the results and perform hand calculations, then use the adjusted preload value for the second run.
Eric,Are you allowed to attached the model?
If you have Fix Separation turned on, you will never be able to separate the parts, no matter how much load you put into the model. For best results, always turn the separation off and insert a contact between the components. And if you're interested in the fastener results, enable Account for Stiffness. Your surfaces are trying to separate, but they are bonded. A positive separation stress means you have a valid interface. Separation stress is the tensile force at the interface to the area in tension at the interface. Can you share the model?
It's not possible to change the default 118°, and users have to have to change it on the fly. So I voted up on your idea.
Claude,When you stated, "Users can't change this value each time they create a new hole feature", what did you mean by that? I was able to change it to 140°, as shown below. Or are you just wanting the default settings to come up as 140°?
Shravan,When you state that the curve will not flatten, I'm not really getting the gist of this request. Are you trying to say that the curve on the end of the radius, as shown below, will not "flatten" or state intact as you try to bend the radius or flatten the radius? You have a radius that is complex, and you cannot unbend this in Creo Sheetmetal, IF this is what you're trying to do. The radius appears to be 360° to help form the inner opening, and the radius itself bends up. We just had a recent post on this where someone tried to flatten a complex radius, and we were not able to do it (but maybe someone else can). But I'm not stating this is what you're attempting. Just need some clarification.
The Reynolds Equation is used in Lubrication Theory, not to be confused with the Navier-Stokes Equation.https://en.wikipedia.org/wiki/Reynolds_equationhttps://en.wikipedia.org/wiki/Navier%E2%80%93Stokes_equations
Eric,If you have a model that is just surfaces, try to merge all the surfaces and then solidify to make it a solid. Then check the mass properties. Attached the model if you can.
You mean explain this?
I really like the way SolidWorks places their Simulation products in a comparison matrix (attached link), as you can expand each topic in the left-hand column for more details.http://www.solidworks.com/sw/products/simulation/matrix.htmUnlike PTC where you have to download each pdf file and study them individually (attached).
When PTC switched from Independent Mechanica to Integrated Mode, the developers removed the capability to check for continuity across element edges and implemented averaging techniques. I submitted a Product Idea to bring this functionality back, but it has never amounted to anything. No surprise there.https://www.ptcusercommunity.com/ideas/2230There are three components to solution governance: 1) code verification, 2) data verification, and 3) solution verification. Code verification is the responsibility of the developers. Data and solution verifications is the responsibility of the end user.
Which SolidWorks Simulation package do you have?StandardPremiumProfessional
I just received this discounted quote today from PTC, and this will give you a better idea on what to expect. This includes Fatigue Advisor, which you may or may not want.
Here are the list prices without discounts and annual maintenance:Creo Simulate 3.0: Advanced Simulation Extension, $11300Creo Simulate 3.0: Basic, $5670Creo Simulate 3.0: Fatigue Advisor, $5670PTC does give companies discounts, such as DoD, etc. You can use one license file to run both Parametric and Simulate. However, Simulate will be a floating client, never a locked license. I submitted a Product Idea to allow a locked license for Simulate, but PTC has never responded.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.