Recently active
Can you provide the link on the Product Idea?
Community,Here's a good web site for downloading free 3D and 2D CAD models. I downloaded a Panasonic Toughbook CF-31 that was made in SW, but the web site has a built in translator, and I was able to download it for Creo (Pro|Engineer), as shown in the second picture. You will have to create an account before downloading.http://www.3dcontentcentral.com/
Good luck on the developers implementing this.
Makes a lot of sense.
Here's the link to the site, and there are a lot of great models to download:http://www.3dcontentcentral.com/
If you respond to an older post, for example, over a year old, why does it not circulate back to the top of the list? Is there a cut-off date for recirculation? I answered a post today that was just a little over a year old, but it doesn't show up at the top in Creo Modeling.
Vladimir,I located a real 3D model of the Panasonic Toughbook CF-31 (minus the handle) in a web site called 3D CONTENTCENTRAL, as shown below, and I uploaded the assembly. It was made in SolidWorks, but this web site has the capability to down load it in many different formats.
Currently, that's the only way I know how to pull a surface on a n-sided patch.
Doesn't the interface GUI show which component it applies too?
Thanks Werner. That's what I was looking for.
Open your Simulate Help Center and search for "avi". There will be instructions on how to do this.
This video is extruding a surface from a 3D curve. It may not give you what you want, but it's a good procedure to know. FYI. https://community.ptc.com/t5/3D-Part-Assembly-Design/Extrude-a-3D-curve-or-a-surface-edge-with-Creo-Parametric/m-p/440451?ru=107006&sr=inbox
Correct. I've used the Express version for a number of years, and it doesn't have STEP export capability.
Claes,I've attached a presentation on Creo Layers.
John,Creo has the capability to manipulate surfaces by using control points. Here's the instruction on how to do it. So yes, you can certainly pull surfaces in Creo, but getting it on your blue curve is something I'm not sure of. We pulled surfaces when I took a WF5 surfacing class back in 2010. Hope this helps.
Hi Robin,It's not uncommon to see "elements not converged" in the run summary because of the way the model was setup. To eliminate this, one needs to include predefined measures in the regions of interest. Plot convergence on the regions of interest, not the whole model. When you exclude elements, this only excludes from measure in the run summary and not the fringe plot legend. I have not look at your model, but if I get time today, I will, and show you an example of stress convergence plotting for the hole and the bend. I think you stated these are the regions of interest. Also, what is the mating geometry that assists in lifting the lug? For example, is it a large pin? Or a hook, etc.?
You could also make this with the Warp tool.
Link attached. This thread was not posted as a question, but just for discussion.https://www.ptcusercommunity.com/thread/105980
A cope should not affect the overall length of the tube in the BOM. I did a lot of pipe coping to manufacture hand railing, and the template for the cope was right up to the edge of the tube. Perhaps it affects in what you're trying to do.
Then I would recommend moving this discussion to the Visualize Community.
Why not make the cope a feature of the part? Since you have various lengths of pipe, some with a cope, some without, you can always adjust the geometry of the tube and suppress/resume the cope when needed.
I submitted a Product Idea to enhance this.https://www.ptcusercommunity.com/ideas/7855
PTC has responded and stated that after making the text flat to screen the text size cannot be changed. While zooming the assembly in/out the size of the font is constant.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.