<strong>Creo Parametric related:</strong> Expert Machinist, CMM, Molding, Casting, Additive, EMX topics, and more
Recently active
It's awfully quiet in here lately!! I was wondering how many have switched to Creo 2.0 for manufacturing and how well you like it? I have it loaded and have been testing it. It seems to be fairly intuitive and easy to use. I have to wait until engineering gets up to speed with it and approves it for production use so I am just testing it at this time.Lots of new and useful features that were a pain in WF5 like helical milling and multiple cut thread milling.SteveThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I have copied toolpaths using WF 4. I'm now using WF 5 and can't seem to figure out how to duplicate a toolpath. Should be simple, right?Any help would be appreciatedLarryThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hi, i'm looking for a post for an old Tree mill. I tried the ones at http://www.ptc.com/cs/cs_26/howto/ncgp4903/ncgp4903.htm with no luck. Does anyone have one or can direct me where to find one? I have a purchased one but would like to get one that will open right in pro-e. We are getting a new Datron M8 which i found a post for through the above link which will work. My goal is to have another that will be accessible with the software for the Tree as well because multiple people would be using the post which i would need more licences.Thanks,JeffThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hello,I and my colleagues have to design turning and milling tools, thus we often need to check the shape generated by these tools during machining.As the cutting edges are sometimes not contained in a plane and/or not in a plane containing the axis of revolution of the tool, we cannot simply use the Revolve feature.The easiest way we found is (in WF5) :1. Copy/Paste a cutting edge2. Copy the copied edge3. Paste special with Rotate transformation (10°) around the tool's axis of revolution4. Pattern it every 10°5. Make a boundary blend of all these copied edgesThe question is: IS THERE A SINGLE PRO/E FEATURE ABLE TO REVOLVE A 3D EDGE (not contained in a plane) AROUND AN AXIS ?Thank you. This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC pro
have a couple of high feed inserted end mills that say I can use up to the full cutter width for cutting, But using the roughing sequence in Pro/Manufacturing will only let you less than half the cutter width for a step over value. anyone have a work around for this issue? I don't know why they would limit you only less than half the cutter.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Stationary Electric Grass CutterThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I am trying to install WF 5.0 on a Windows 7 64-bit machine. When I try to set up the startup directory, I cannot see any of my network drives. Anyone know why? I was able to do this with WF 5.0 on an XP laptop just fine. Thx.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I'm interested in displaying multiple analysis features and their corresponding results in a table on a drawing. I'm attempting to create a composite table that displays not only the typical component data but also other informaiton we use for our manufacturing purposes (trim lengths, drill diameters, etc.). It's very possible I'll have multiple length analysis features, multiple diameter analysis features, etc. The analysis features will often be created referencing imported geometry. My question is this...how do I display in my table the details for each analysis feature? An ideal solution would be one that automatically updated as analysis features were added or deleted. Is this possible? I am not an expert in tables, relations, parameters, etc. so if you don't mind I'll need detailed answers.Thanks,DavidThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the
I started on pro/E in ’96 on rev 16, but I worked for an injection mold tooling shop. In the mold package, matching accuracy between the molded part and the mold extracts was crucial, so we always used absolute because relative made it hard to match. So I’ve used absolute accuracy at 0.0001” from the beginning with no issues that I can recall. The issues I’ve had with accuracy have come from using relative rather than absolute. Doug SchaeferThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I found when i post out my NCL file to say a Haas post processor in a drill cycle the first hole location is always skipped. The hole is is the first move position but not under where the drill G code is. Any idea of how to fix this. Seems like the post is the problem. Here is the code, it is suppose to drill 4 holes not 3 and the hole that is missing is on line N20.JeffN10 T7 M06N15 S30000 M3N20 G0 X10.235 Y2.0085N25 G43 H7 Z.187N30 G83 X9.335 Y2.0085 Z-.0388 R.187 Q.03 F20.N35 Y.8665N40 X10.235N45 G80N50 M05This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hello, Does anybody know of a post processor for a Huco VTXU 5 axis table table machine? I am running Creo Elements Pro or Wilfire 5.0. Any info would be a huge help.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
hello everyonebeen using creo 1 for a few months im having trouble when trajectory milling , if i take more than one cut the plunge feedrate only works on the first cut but after the first cut it plunges at the cut feed rate which can be too quick sometimes is it possible to change this.thanks for any help mickThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
When I post a .ncl file my RPM's won't go beyond 10,000 even if in the paratemers they are at say 25,000. Any ideas how to fix this? Seems like it's a software issue setting???Jeff
hello everyoneive been using creo 1.0 for a few months now but have trouble when trajectory milling. when i take more than one cut the plunge feedrate doesnt appear on any cut sfter the first one. the cutter plunges at the same feed as the cut feed rate, am i missing something? trouble is when machining at fast feedrate the cutter plunges too quick.thanks for any helpmickThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Hi everyone, I was wondering what people use for high speed tooling. We are trying to figure out what or what not to get or do. Can people give there experience with diameter with respect to flute length, suppliers, special balanced tools (can't seem to find anything definitive with manufactures) will any 2 flute or single flute carbide end mill work? Heard from our machine trainer any 2 or single flute carbide would work and we have plenty of carbide tooling here in house we would like to use if possible. How much can be hanging out of holder. Max speed of machine is 40,000 RPM.Thanks again,JeffThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able
When I startup ProE on my productview machine, using proepublish.bat I'm getting this error in the std.errThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
How NOT to Design for Manufacture There are many articles, and blogs, out there telling you everything you need to do to be a great designer. I have come to the conclusion that these are either incomplete, inadequate to solve the problems of design, or they are not reaching the legion of designers and draftspersons who cannot read. Therefore I have put together this blog series to explain how NOT to design. Hopefully, through its subtle humor, it will be able to reach the hopelessly backwards. Don’t be offended by the label, if you are hopelessly backward in all likelihood you don’t know that you are. If you at any point find yourself getting huffy puffy about a particular portion of this series don’t worry, there’s hope for you yet and you are merely backwards. Manufacturing ProcessesDo not learn anything about how mills, lathes, presses, or any of that o
All,One of my customers just provided me with a .txt file with what I believe to be G code. The data looks like:<h3><h2>.</h3><h3>.</h3><h3>neal@geometrixeng.c</h2></h3>This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I don't understand how the information in the CSYS/OSYS line can be used to calculate an angle.I have extensive knowledge of our Post Processor and can output a specific set of Coordinates as a G10 output to the controller if I could "Calculate" the position and orientation of the CSYS/OSYS command.I understand that the following is for NO ROTATIONS and position at X0 Y0 Z0 (A0) (C0)$$-> CSYS / 1.0000000000, 0.0000000000, 0.0000000000, 0.0000000000, $0.0000000000, 1.0000000000, 0.0000000000, 0.0000000000, $ 0.0000000000, 0.0000000000, 1.0000000000, 0.0000000000But I don't know how to translate something like this$$-> CSYS / -1.0000000000, 0.0000000000, 0.0000000000, 0.0000000000, $ 0.0000000000, 0.0000000000, -1.0000000000, 0.0000000000, $ 0.0000000000, -1.0000000000, 0.0000000000, 0.0000000000Mathematically into directionsThanks in advance.This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please
Hello everyoneim a fairly new user to pro e had it 3 months now im having a problem that when i generate the nc file when it generates the g3 or g2 code with i and j code if i take more than 1 cut the i and j code are mising, if i just take the single cut the i and j are there. im using pro e 5 and creo 1.0 any ideas would be gratefull
From license file#PROE_FAPAAX 2 Creo Advanced XE with AAX (formerly Pro/ Creo 1.0 Flt Lic perm#PROE_FoundationAdv 2 Creo Parametric (formerly Foundation XE) Creo 1.0 Flt Lic permMaybe it's the XE that makes a difference.On Wed, Feb 22, 2012 at 10:08 AM, Steve Cooke (C & S)<-> wrote:> Michael>> Was there an upgrade cost?>> I have asked this specific question and this was the answer from my VAR> (Only one in South Africa so I don't have much choice!)>> Quoting:> "To answer the second part. on upgrades:> We can upgrade from Creo Foundation to Creo Parametric, it sells for R20,000> (based on USD of R 😎 and requires that your maintenance be up to date on> the package before we can upgrade it."> End quote>> In spite of the above he also is quick to explain that there is no such> thing as Creo Foundation to buy as a new user. But any functionality missing> from your ProEngineer foundation license will be missing in Creo if you move
Hi all,I'm having some trouble storing my mapkey button icons and hope some of you can give me a hint.I customized my ribbons and menus adding my own mapkey buttons and creating icons for them. After that, I exported my customization .ui file to a server so I can open it in another machine.The problem is, when I import that customizations, it brings all my buttons, but they come with the funny yellow face instead my own custom icons.Anyone can help me with this one?thanksEmanuelThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
I'm new to pro/E and Creo. I am having trouble with the expert machinist output to G-Code. My Machine tool does not like the format of the post processor. I have the basic 2 ½ D CAM that comes with Creo. The post outputs the tool path in as follows: N0012X00035Y0015F01. My machine tool interprets this as X=35 and Y=15. It should be X=0.35 and Y=1.5. In addition, can I adjust how the line numbers are generated? I would like to start at N0010 and increment by tens. I cannot find in the documentation how to change these formatting issues. I have tried using the NC Post Process under the Applications menu, but I’m not sure what It is actually doing. There is only the one default profile UNCX01 under the machine setup. And the list file says its using the UNCX01.p00 file (This file does not exist on my Hard drive.) So I’m at a loss. Any help would be appreciated. ThanksThis thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open t
Users, Abusers and Downtown Cruisers; I have two questions forthe users that are working with Pro/E and PDMLink. I am wondering if y'all are willing to share how your company handles these two scenarios in PDMLink:Non-Solid CAD Changes After Released: The models and drawing are at a RELEASED state, but there is something that needs to be changed or added in the 3D models. For example, you need to hide a Layer, add a Datum, fix a frozen or failing component's assembly constraint, add a Simp Rep, etc. We do not want to REVISE the model to bump it back to a state where it can be Checked Out, changed and Checked In. We are changing the model only, not the drawing. How are you handling this at your company? Make Minor Changes to A Drawing (or Model) During the Approval Process: The drawing is going through the process of being reviewed/approved. After ~10 people have reviewed it and approved it (Engineering, Manufacturing, Purchasing, etc.), one of the people in the process (Quality)finds a
I have been finding more and more gouges lately and i am wondering if any one else has been finding the same. MAINTAIN_CUT_TYPE will generate these strange circular gouges. This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.