<strong>Creo Parametric related:</strong> Expert Machinist, CMM, Molding, Casting, Additive, EMX topics, and more
Recently active
Hi programmer, my problem is how to generate correct coordinate and C axis in tap file? I use Mill-Turn type machine to do side machining of part which machine has y axis function (Like above picture shown). However, I have setup "planar machining" in my post file which included I defined output code for G1 and defined C axis of "Option for ABC angle output", but Creo always generated "G1 C0" when planar machining has different angle. Also I found that Mill-Turn type need to define Z axis direction for Horizontal of coordinate setting which setting different with 4 axis Mill type (Z axis is Vertical), therefore, Creo refer to sequence coordinate then cause Creo generated wrong coordinates in tap file. Have a good day!! Mark Rao
Can you use the same engineering drawing for the US and Europe Manufacturers?Most of the US Manufacturers follows the First angle projection and Most of the Europe Manufacturers follows the Third angle projection.If we have to send the same casting drawing to the both supplier with their requirement what we should do?Creating multiple drawings for the same model is a bad Idea. During changes in the model causes update required for all the drawingsSo create the same drawing to use both First angle and the Third angle projectionSee this link for the article, how to utilize the drawing program to maintain first angle and the third angle projection with the same drawinghttp://jkparthiban.com/index.php/2017/04/15/creo-drawing-program-utilize-drawing-us-europe-manufacturers/
Hello, l have a long time problem with model accuracy. l understand it´s different from company to company. Company no. 1 is specialist about fine optic lens with high accuracy. Company no. 2 is specialist about rought machining with lower model accuracy. Our company produce a air-ducts. It means 5000 mm long duct, DIA 1500 mm with 2 mm wall thickeness ---> it´s a big difference between lenght and thickeness. Rules that l have to keep: - all models have same model accuracyMy information about accuracy: - absolute is better than relative - set absolute = 0,002 looks fine? Questions:- do you have any expierences with model accuracy? - could you share your "standard" model accuracy? Thanks for informationMilan Bonka
Is there a way to create your own custom unit cells for Additive Manufacturing module? Using beams or surfaces. I would like to create a diamond lattice out of beams I would like to create a face centered cubic out of beams I would like to create a octagonal, but with surfaces instead of beams. I want the ability to turn on and off selected surfaces, assign a thickness to the surfaces and vary the density, just like in beams. This would create a closed or semi closed cell structure that is self supporting for 3D printing.
Hi, Does anyone have PP for iTNC 530 (Heidenhain) control for Creo3? Thanks in advance. Bence
Hello Programmer,I met a problem of FIL that I need to get "Fixture offset" value by using FIL, I can't find the number code of "Fixture offset" in the Gpost. Can you teach me how to compile FIL to get "fixture offset value? thanks!!Have a good day!!Mark Rao
Area turning parameter contains the LEAD_RADIUS option in the entry exit list but it can not be used except for the profile motion.LEAD_RADIUSThe radius of the tangential circular movement of the tool when leading in or out. Used when creating Lead In and Lead Out Tool Motions, and in Build Cut for Profile turning. The default is 0.****************************************************************Sandvik has developed a method for a reverse turning concept (Prime Turning). See article Modern Machine Shop June 2017 page 71 for complete details. Using this concept the tool must lead in using an angle approach and radius value very much like milling allows. Each roughing pass in the area turning must include this lead radius. Creo Area Turning can be used for Prime Turning if the lead_radius option is added to each pass. Different feed rates will have to be applied to the lead_radius for this tooling and Area Turning has this option by using the APPROACH_FEED parameter.Currently Maste
Hello all,I have a question, to which I cannot seem to find an answer. I am hoping y'all will be able to help me.In my work, we use plate steel and bend it. Pretty simple. I use the Sheet Metal application (Creo 3.0, M090), so that I can flat pattern the parts and be able to tell the manufacturing people what the overall length of the part they will laser out needs to be.I sketch the part in its bent state, and I have been taught/told as best practice (or so I believe). Make some cuts, and I have what I want. I sketch a curve that is half the thickness, and then created a parameter, as well as an analysis feature, and tie said parameter to the measurement. This was, I know what my length SHOULD be. (see my first slide in my attachment) In the first slide, its just a 3D view, and the sketched curve is there to be seen. I have the curve projected to the same height as the points at the ends.When I put the part on a drawing, I no
Have you downloaded Creo 4.0 yet? Printing parts made in Creo has never been easier. Now, you can use the software to set up a tray assembly, arrange parts, and test them for printability before you send them to the printer. Our expert explains how:To explain the basics of tray assembly, let's start with one part.Selecting the engine cover to create a tray assembly.You can prepare that part for 3D printing, then use automatic positioning and add other parts.Place as many parts as you want into the tray.Adding a fuel cap to the tray assembly.You can also create a pattern, which you can use to create multiple instances of a part. For example, select one part and then define the pattern, then select the number of parts. In this case, we are using direction. You only need to worry about the number of parts.Creating a pattern of the parts using Direction.When you click Auto-position, the system arranges the parts inside the tray.The parts are arranged automatically inside the tray.Let's cre
How do I combine multiple mold volumes into one volume in Creo 4.0? I can't find it. Video Link : 7910
I recently updated Creo 2.0 from M090 to M240 and noticed on a couple of occasions that I am getting some flats in the tool path when using Cutline to Circle Interpolate a hole. I have seen this before and can sometimes fix it by loosening the tolerance, but it has been a long time since I've seen it and I do a fair amount of this.Is this anyone else has noticed or am I alone on this one?Matt
I would like to know how to turn on 3D Cutter Compensation in Pro/NC. Hereis what is output to the NCL file when it is enabled: MODE / 3DCOMP, ON...CUTCOM / ONGOTO / 24.4070718118, -11.0963791260, -8.2054735622, $0.2054965047, -0.2582157475, 0.9439787150, $0.5364531275, -0.2645786937, 0.8013839011GOTO / 24.8306712658, -9.7398669112, -8.0725117395, $0.2054965047, -0.2582157475, 0.9439787150, $0.5205224109, -0.2254581166, 0.8235442049Thanks, Fred NemecekAustin N.C., Inc.512/458-1112 x19
My goal is to be able to add or edit CL Data in any area of the CL code, so that the edits stay in the manufacturing model in case they are coded out at a later time. According to these PTC instructions Creo Parametric Help Center, it should be easy and available right in the Play Path box. This would be extremely useful, however I do not have the option, mine is greyed out and unselect able.The only other option that I can find is by going to manufacturing tab and then selecting Edit/CL Command, however this only allows me to select "beginning" or "end" for my placement of code, and does not allow me to specifically place lines of code like I am attempting to do. In this mode I can also select Edit/Edit Mode in the code window and change the code and then save it, but it does not seem to keep my added CL Code. I just want to be able to add or edit CL Code on any line that I desire, anyone have any ideas?guys.Thanks again
Curious if anyone is putting derived from (saved from) information on their drawings. It would help our manufacturing department to know where a model was copied from since often times they already have the machining programs written for the original models. Windchill can provide "saved from" information, but this is only available when the save-as event took place inside Windchill. Frequently we do the save-a-copy from Creo itself so the table in Windchill is empty. Creo files do have an internal history log, but I don't know of any way to expose this information on a drawing. I imagine we could use a parameter and just type in dumb text, but I'm concerned about this being done correctly and consistently, not to mention that a rename in Windchill would create a complete disconnect between this dumb text and the actual model names. Any suggestions? Does anyone else provide this type of historical information to their downstream users? Tha
Hello,I would like to suggest a small improvement to library component editor: It should have a field for Tags. When we are searching for a component in library, we don't always remember the name of the file, specially if it was made by someone else.In this example, I would use tags like: Cashew gate, Tunnel gate, Curved tunnel gate, Gate insert, tgs, etc...Then when we make a search, emx search not only for filenames but also for this tags.Thanks,Jose.
Hi! Are there any plans to include machine kinematics simulation along with Material Removal Simulation in ModuleWorks?This combination of simulations would be extremely useful!! I have not found any way of combining this so far.
Dear all,When using the roughing sequence to rough a pocket I see there is no option to enter a plunge feed.When using an end mill this is essential in order not to damage the flutes.I've tried entering a ramp speed and specify explicitly a ramp angle of 90° (which is the default setting).This has no effect on the resulting toolpath. The only feed applied is the default cut_feed.The volume rough sequence does have this option but I can't use that sequence for this particular toolpath.Is it possible to specify a plunge feed with the roughing sequence ? John KU Leuven - Technology campus Diepenbeek
Hi,I'm here for a little problem with Creo 2.0 in Manufacturing->NC AssemblyAfter the creation of all the functions, I generate a .ncl file.But the creation of the .ncl file take to much time (sometimes 10h)During this time I look in the system monitor, and I see only one core work on the 8.Can I use more cores to generate the .ncl faster ?TanksThomas
in EMX, when deleting the ejector pins or any other components, the related section views are getting deleted with out any warning. I understand that creating section views without relating to EMX components will do. But is there any other method to avoid this. It will be great help because randomly I am creating new section views after removal of EMX components.
I am trying to implement thread mills into Creo negating the need to use a code generator from the manufacturer, so that code can be reliably posted from the manufacturing model.I am having troubles setting the depth of the NPT, as there seems to be no "thread length" in the parameters, or depth option. I am not completely sure, but this depth appears to be controlled by entering the number of teeth on the cutter, in the "flute" field of the tool information. This seems like a very odd way of controlling depth, is it how it is done?The code generated when doing an NPT thread mill is many lines of point movement rather than a few lines of canned cycle. There is no G03 movements output at all, and this makes for a very awkward and VERY long program, any workarounds?Placement of the thread when choosing start and end. I am having problems with the placement of the thread, I have attached screenshot to help explain.In this demonstration, I have made a sample part that is
i have issue with modelling of attached pipe DWG can someone help me to do this.thanks
When I insert parts from EMX and I hereafter open the parts, the datums are always hidden in layers. In the layer its called 00_buw_datum. QST: Why are these datums always hidden. Everytime i import a part and i want to use the predefined datumplanes, I have to unhide and save status afterwards. Is there a way for these datums to always be visible? Thanks. Clement
Some customers have reported problems when trying to use EMX the first time after they have installed it. Usually the functions "Project> Create New" cause a crash OR "Administrator Tools > Options" show empty sheets. In this case, please check the content of the folder <emx_install>/configuration. If you see only this files: the most important files to run EMX are missing. They are shown here: This are localized files that should be created by EMX when starting it the first time. Since MS Windows 8 the handling of Administrator rights for the folder "C:\Program Files" is rather restrictive, therefore EMX is not allowed to generate this important files! To solve this problem, either make sure you have 100% administrator rights for this folder OR install EMX into a different directory.
Hi everybody,Does anybody know how to eliminate the transparency on plates created in assembly definition?Within EMX options - Technology - Face color :I believe that this is the place to define the colors on the various plates.BUT i cannot set the transparency!... Where to do this??Thanks in advance:)Best regards Clement
Where can we find the file that explains whats new and improved for EMX 10? What is the significance of F000 vs M000 for the build number?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.