Skip to main content
Apr 2, 2014 11:38 PM UTC
Delivered

Stop Model Tree Reorder Becoming a Restructure

Related products:Creo Parametric

I've been asked to raise this enhancement request on behalf of a couple of colleagues.

Their main issue was:

"When trying to drag a component for reorder in the model tree, the holding time is too short to reorder well, the component will get restructured into another sub-assembly"

And the response we got from TS was:

"The issue is considered as works to spec since the holding time was implemented per PD's decision."

The users are finding that when they try to drag a component in the model tree to reorder, Creo is restructuring the component into a sub assembly.

Once this happpens, the ability to undo is lost and it is a pain to back out of.

Components are snapping way too quickly into a restructure.

We would like to see either:

1. Slow down the process (back to 2 sec as it originally was) so the the user has time to see that a restructure is going to occur instead of a reorder.

2. Have the ability to toggle and choose b/w restructure and reorder if the system defaults to a restructure.

3. A config setting to allow the user to set the default time to a longer value.

31 replies

Apr 2, 2014 11:55 PM UTC

Oh this so needs to be fixed!  I "lost" a component recently only to find it in a completely unrelated subassembly.  At the very least I want a notice confirming that this is indeed my intent.  And the undo no longer functioning after the action is insane.  Who wrote the functional specification for this anyway?  It may work as specified, but certainly not as a common user would expect.

Apr 3, 2014 3:21 PM UTC

If I am not mistaken, this is what I was eluding to back in this post. I just didn't put forth a product improvement idea.

http://communities.ptc.com/message/191905#191905

Thanks, Dale

Apr 23, 2014 6:44 AM UTC

Another idea would be to make the action sensitive to the point where you push the pointer while dragging the component you want to restructure e.g.

If you point to the name of another subassembly or group then you want Creo to drag the component or feature into that specific subassembly or group.

snap1161.gif

If you instead point to the model tree lines (between the symbols of two subassemblies/groups) Creo should just drag the component/feature in between these two subassemblies or groups.

snap1166.gif

I would not like to stop the restructuring with the model tree but to improve its behaviour and avoid "intuitive misunderstandings" of the users intension by CREO

Jun 29, 2015 8:59 AM UTC

My users are complaining about this too, and I have just repaired an assembly where 3 of the 4 first components "magically" dissapeared. This unwanted restructure is my first suspect.

Jul 7, 2015 5:52 PM UTC

In Piping the reorder is a must to work correctly. This behavior It is causing all kinds of grief with the end users.

Mar 16, 2016 11:58 AM UTC

It seems to assume that if I'm reordering, I'm restructuring and snaps parts into subassemblies, even when I was trying to do simple reorder. Slowing down software's decision for me may help. Or simply pop up a selection box, reorder/restructure.

Mar 18, 2016 4:06 PM UTC

I am trying to be very cautious when moving components in the model tree. It does not seem to matter though as I keep getting stung by this "feature" that automatically place components into assemblies. I cannot undo. I cannot drag it out. I have to delete and reassemble the component and anything that is assembled to it. This has cost me alot of time and heartburn.

Mar 21, 2016 10:07 PM UTC

When dragging and dropping a component between two sub assemblies in model tree, the component ends up in the wrong location because at the last moment, it drops it into the sub assembly instead of in between the two sub assemblies.  The sub assembly icon momentarily changes right before you drop the component in between the two sub assemblies and you inevitably drop the component into the sub assembly.  In fact, it is almost like you have to "throw" the component and hope that it hits between the two sub-assemblies -- it happens that fast.

Product Idea:

Make the hover time over a sub-assembly a longer so that users won't inadvertently drop the component into a sub-assembly

See PTC case numbers:

C12978707

CS158767 -- see demo; https://www.ptc.com/images/cs/articles/2014/04/16021750_C1GN.wmv

This issue shows up as #3 in the "Most annoying things with Creo" from the PTC Community, thread 40446 MOST ANNOYING THINGS WITH CREO

May 20, 2016 3:54 AM UTC

This always happens to me too. If I hold the mouse button down and hover I can see it's going to go to a sub assembly so I don't let go of the mounse button and bring it back to where it was. Sometimes I'll try this 3 times in a row before giving up. I noticed this right off with CREO 3. Never used CREO 2, just CREO 1

Sep 2, 2016 7:38 AM UTC

I would like to have a config Option to disable a restructure.