Recently active
When dealing with large assembly with thousands of parts it is very cumbersome when you want to see where specific object (part or subassembly is used), although prehighlighted as object might be very small compared to the assembly thus hard to see. Idea is to add Focus command to RMB menu, which would then zoom in (focus) to the selected object. The same command might also be implemented to the drawing module, where one would additionally need to select also the view for zooming in.
Method to align text (of any font) so you can add numbers 1, 2, 3,.... followed by an aligned paragraph. Preferably a space that can be adjusted. Essentially a way to create what would be considered a standard engineering note on a drawing. If standard text formatting is not possible in a Creo drawing (hard to believe), Perhaps a table, or repeat region, that does not have visible box-outlines? End.
When using the Mass Properties tool in an assembly, it only calculates the volume and mass of the full assembly. It would be useful to be able to select a single part (or multiple parts) and query its mass properties (or the sum of multiple parts' masses).
When closing a Creo window, focus shifts to the window of the part, assembly, or drawing that was most recently opened. However, the behavior that is most expected by the user is to return focus to the most recently viewed window. This problem most often comes up when detailing parts in an assembly. Let's say you started Creo, opened up Assembly A, and then Parts B and C. While working on the assembly, you want to add some changes to Part D in there, so you select the part and RMB > Open. After making the changes, you close the part window to go back to the assembly and view the changes in context. However, instead of switching focus to the most recently viewed window (Assembly A) it switches to the most recently opened (Part C). This is unexpected and jarring and you have to then manually find the assembly in the window list to switch back to it.
Add extra parameters in the Wire List. I like to get following parameters but with the current list it’s not possible. Name, Wire/Cable, FROM RefDes, FROM Part Number, FROM Pos., TO RefDes, TO Part Number, TO Pos.
Can we get a selection box highlight option while in the explode tool? I hate having to pick each component I want to move individually. This would be a big help when you have already moved several components and you want to select them again.
In Creo Parametric 4.0, when entering double-byte characters input into a note, there is no function to display the character before confirmation in the input box.Double-byte characters are displayed at the top left of the screen.
With tool design for designing a mold,there's a limited undo functionality in the sub-tab "parting surface", if a sketch is made, there is also no way to delete it until the command is canceled, which can result in a loss of effort (the good sketches are lost as well if you cancel the parting surface command). I'd like to see the general functionality inside the parting surface command working just like the rest of creo , adding sketches and deleting them should be no problem.
There are situations where we have a family table with instances, that need to be broken. The old instances become standalone parts. However, when this is done, any coloring that was created in the generic does not get transferred over to the new standalone models. Therefore, all colors for these ex-instances are gone! Please rework the functionality such that all of the coloring does not get lost, requiring each instance to be redone! See PTC ticket 14857942. Thank you!
1. This mid surface feature will be useful to create a mid-surface for FEA simulation. 2. I heard that such a feature is available in Creo-Simulation. 3. It will be good if you make it available in Creo Parametric. This is because we prepare CAD in Creo parametric for simulation and take it to our preprocessor.
Allow a data flag to be placed on a conic surface in a view per ANSI Y 14.5 example. Customer needs to define the primary, secondary or tertiary Feature of Size which happens to be a conic. The conic is built on two 180 degree arcs. The workaround is to place a datum plane perpendicular to the drawing view for datum flag placement. This does not always work. Placing the datum flag directly on the conic surface, allowing the silhouette edge to be perpendicular to the drawing view for displaying the datum flag would be ideal.
I mean to add a saving option .jpeg or other pics format.
I want to be able to change the font used for view notes and arrow text in 2D cross sections and projection detail views.
I want to input a note with double strikethrough in drawings and annotations.
For example, datum plane creation, measurement of analysis menu, etc. window always appears in the upper right, but I want to freely set the initial display position. We request because there is an opinion that it is difficult to see other menus overlapping.
We have 2 sheets(assembly) with 2 different simplified representations. The 2nd sheet's representation is such that some components are deleted from it. Our methodology: 1. create the 1st sheet as per our need. 2. copy the 1st sheet. 3. change the representation of each view in the 2nd sheet. As soon as we change the represntation we lose all the BOM balloons. So we are looking for a way in which we can save time in re-creating the BOM balloons for 2nd sheet. We need a solution such that changing the representation does not delete the BOM balloons
Opportunity to create top level comment lines at the same modeltree column like the component, features, ... in Creo Parametric 4.0. Also would it be great to highlight the comment lines with a color. The comment lines would be very helpful to make the modeltree clearer and more informative.
Inside a MBD world, it's important to use the correct tolerance system and model DTL settings. A mix out of different settings is creating downstream problems and mistakes. Therfor a user needs to use ISO DTL settings and ISO tolerance settings inside a model. Changing a model tolerance setting from ISO to ASME or wise versa at a later state will change all finished defined annotation tolerance values inside a MBD model. This is very critical during an active design phase and also for downstream processes in a digital world. The model with its tolerance value and setting is driving the quality of a downstream process. In case a tolerance system change will be done at the end of a design process, because the validation process is reporting a wrong selected tolerance system compared to DTL settings, all tolerances will get converted automatically and needs to get reset manually. This is a very big and potential error for downstream usage and model quality. Proposal: If the tolerance
At the 2019 Winter PTC User conference a future enhancement was presented to collect all of the non-referenced surfaces to support the ASME Y14.5 paragraph 8.2.3 requirement for surface profiles contained in a note. This enhancement idea is along the same lines only for true positions. If there is a note on the drawing that states an "unless otherwise specified" true position, then all non-referenced hole features should be collected and a default true position should be applied.
Way to use a template when adding a subsequent sheet to a drawing
Reference https://www.ptc.com/en/support/article?n=CS251200
The ability to use baseline dimensions in the sketch and have it show up in MBD or toggle ordinate linear in MBD like a drawing so you don't have to do double work and potentially miss a dimension manually adding ordinate dimensions in MBD.
Since Creo 3.0 the workflow for paste special with advanced reference configuration was chaged. If the reference dialog for the paste action appears it is behind the active window at the beginning. If the user clicks on the reference selection window it comes to the front. When moving the mouse pointer above the reference of original feature area the original window (where the feature was selected) comes on top. The reason for that is to have the original model visible where the feature was copied from. This was changed because of an user request (see Article: CS287471). That behaviour ist not very streamlined and the current workflow is to make the Creo window of the source part smaller to have full access to the dialog. The idea to change that would be a second window that should appear inside the target window showing the source part. The same behaviour as it is when selecting references for copy geometry.
If you add parts from the prt file and become an asm file, the drawing dimensions will not be preserved. Therefore, it is inefficient every time it is rebuilt from scratch. I hope the drawing dimensions are preserved.
It is possible to include a Layer Names column in the model tree. I was initially going to recommend this to our users that are not familiar with layers, but I discovered that this only reflects if the feature itself is in a layer. In the image below, the starting datum elements are in layers as shown. However, Extrude 1 is not shown as in any layer. Extrude 1 however, does contain an axis in the 3_ALL_AXES layer, and feature information reflects this. The "Layer Names" column should be adjusted so it reflects all entities in "Entities and Geometries" in the Layer section of Feature Info. This can help users quickly and accurately track down what layers are controlling items in a feature.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.