Recently active
Currently one can drag mechanism using CTRL+ALT or with Drag Components tool. When mechanism have multiple joints one will find it hard to drag just one of them. If one could have a slider type control for each joint, then it would be much easier to control the movement of mechanism. Today one can isolate movement to only one joint using joint locks, which is a cumbersome workaround at best.
Idea Enable Performance Advisor to show the real Login Name and Host Name of sessions instead of the masked data currently available. This should be configured for users with proper privileges, assigned through the eSupport Account Privileges for Performance Advisor for PTC Creo, and if this data have been willingly sent in unencoded form for that purpose by configuring the "PTC Diagnostic Tools" data filters: Background There is no easy way to find out the correlation between the masked data "User_ID" and "UUID" and their counterpart like User Name and Host Name even if this data have been willingly sent in unencoded form for that purpose by configuring the "PTC Diagnostic Tools" data filters. Therefore the Performance Advisor, a tool that would be really useful, loses a great part of its effectiveness because of difficulties needed to identify quickly in the dashboard the failing sessions using masked data instead of actual User Name/Host Name
Today I can set the setting to 0, which allows full use of the hard disk as cache.Furthermore, you can set the cache to a fixed size in megabytes. As an extension of this setting, we would like to be able to set negative values.This should result in the maximum size of the cache equal to "size of the hard disk" minus the value of the config.pro setting. This would make it easy to ensure that a minimum of disk space would always remain free, regardless of the hard drives used. Today we have the problem that some computers have 256 GB and some 512 GB hard disks installed.If you want to prevent caches from becoming corrupted due to a full hard disk, the value of the setting dm_cache_limit must be limited to 261120 MB (= 255 GB).But the computers with 512 GB hard disks would allow much larger caches.
When a new illustration is created is not possible to change the setted "standard". Then if I need to customize some callout, symbol, explode lines in an old illustration I need to redo it now. It is not acceptable for us. Thanks
Create a config.pro option to enable the user to set the default selection for the smart filter in Creo Parametric 5. For assemblies, the current default is "geometry" but setting it to "part" would be more useful to me.
Hello, Sometimes, after defining a Combined state with 3D annotations in Creo Parametric, when exporting the assembly to pvz and opening the viewable in Creo View, the combined view opens in a different orientation (translated in Creo View compared to whats defined in Creo Parametric😞 The user opening the same combined view inside PVZ can think its empty or in best case need to translate the combined state to have a correct display ! Can you please Correct this behavior : an orientation defined in Creo Parametric for a combined state should be always exactly the same when reopened in Creo View ! Associated PTC Case : C14627537 Thanks in advance
PTC Creo should implement conversion, compatibility or even method switching in terms of Bend Allowance calculation and table. Both Creo Parametric and Creo Elements Direct Modeling Sheetmetal Shop should be 100% compatible to each other and to bending machines terminals. Today Creo Elements Direct Modeling Sheetmetal shop is, while Creo Parametric is not.”
Bend Allowance calculation and bend table should support or even convert both, Bend Deduction and Developed Length.
PTC is reducing the functionality of Creo Parametric in the name of "meet(ing) dimensioning standards". One example of this is the removal of the user's ability to rotate ordinate dimensions. However, they are ignoring the fact that a lot of "drawings" that are created are never intended to meet dimensioning standards. Layouts, flat patterns, templates and most importantly presentations.It would be great if PTC would allow both a standards locked mode and a free mode in order to facilitate all uses of the drawing module.I opened a case with tech support and the tech went the extra mile and submitted an SPR for an enhancement to add a config.pro option to enable this. Maybe we'll see it in Creo 4.PTC, allow designers to use Creo the way they need to, not just the way you prescribe.
Customer need to use a function that can store file paths of used parts in assemblies and drawings.This can be possible by PDM capabilities but for small companies this is expensive. According to them other CAD solutions has this option. They do not want to define search paths because this is time consuming process while getting data from hundreds of folders. Also search path gather the first file that it found but the correct part may be in another folder.If it is possible to make assemblies and dreawings to remember file paths for used parts then it will be easy to manage and fast to open these files.
Would like to be able to copy geometry, surfaces, edges, etc.. Then paste special, which would create the geometry which was then non-dependent of the original geometry. This would allow the suppression / changing of the original geometry with still having the copied geometry for other uses.
Since Creo Parametric 2.0 it is not possible to open a CATIA file with the file accuracy.
It would be nice if I could select the group or pattern to manipulate, instead of having to open / expand said group or pattern & choose each instance in said group or pattern for selection / manipulation.It would also be nice if I have failed items or features in either a group or pattern that the group or pattern icon changes to indicate as such.. Have it turn red like single parts / features / assemblies do. (I get the square that it’s suppressed though..)20 or more pattern & groups opened up / expanded can make for a very long model tree!! And, as far as I can see, groups do nothing more than to help clean up the tree.
I wish that Creo retained the last ‘user entered’ value or choice. Not always defaulting back to whatever the default is. Welds, point placements, hole sizes, flange lengths, etc.. (Mind you, there is one or two variables that do get kept, but these are minor ones). If I’m laying down a bunch of welds, each & every time I pick the weld to lay, I have to re-enter the size, length, depth, shape, etc.. Yes, I can pick it from the list, but each & every time, 4 variables to pick; 8 clicks.., And I’ve got about 5 welds per corner of my octagon welded box.. I’m laying out a few flanges (or flats). It would be nice that the length of the flange remain constant, so I don’t have to change the length each & every time (and why is it always some weird length?!)I’m dropping a bunch of holes onto my part. They are all ¼-20 tapped, 3/8" deep. But each hole requires (like above) that I pick & click the size I want.. Again, I selected "tapped hole, ¼-20".. Remember it till I nee
Allow the text line (tail) to have more than one line of test! Many times I’d like to add a 2nd or third line to the process. (And fix it so I don’t have to add a space at the beginning or the end of the text line, so it doesn’t run into the < of the tail!)Fix it so the line is adjustable. If I have just the fillet mark, I don’t need a line sooo long. And, if I have 4-13/16" welds every 5-1/4", the numbers all jumble / run into each other.. The line won’t adjust itself to fit! Make it so you can drag the length of the line.Mainly for plug welds, but if I don’t have a number of welds (number under the symbol), and I ask for a surface (flat, concave, etc..) the surface feature indication is way below the weld symbol, so far that it can be considered an extraneous mark on the drawing, not a part of the symbol!Make the leader reference notes independent. As it is now, you have to choose left or right sides (and they seem backwards), and if you flip the weld symbol, you have to re
This would fix a few dimension issues that have popped up with Creo 2.Add a button, a 3rd step to ‘flip text’. The 3rd step would flip it to the middle, so you have the choice or ‘left’ right’ and ‘middle’. And, while we’re at it, put back the functionality to grab & move the text around like we once did.Ordinate dimensioning; make it so when you add a jog, you can still move the dim up & down, left & right. Now, once you add a jog to the leader line of an ordinate dim, you can then only move it in the plane in which it was set. (you used to do it in WF5)
在WGM工作区里面新建CAD文档,然后导入数据的文件是中文命名的,检入系统之后再打开CAD文件就出现空白或者添加工作区失败!
Filled hatching cannot be used in views with clipping (i.e. detail, partial, broken) as stated in the help documentation titled 'About Creating a Filled Area'. This is very annoying and it would been useful if it can be possible. Thus, when the drawing is complete and we decide to change the view to "partial view", we will not need to change manually all the hatched part that have been filled.
Shaded views are a real nice add to the WF and Creo offering over Pro|E.However, the output quality leaves a little to be desired for drawings when shaded views are deployed.In particular, many companies like that little ISO Icon on what is otherwise a normal line drawing.However, the lighting and chosen colors for modeling do not translate well when printing drawings.typically, the icon view is too dark to print with any discernable contrast.A light rendering module in the drawing, for instance, option to turn everything white with shading, or ensure a forward facing light can be adjusted to get a consistent brightness on everything would be -very- helpful. Even an auto brightness feature would seem appropriate!What we get:What we want:
We have two .brd files that we want to compare. Currently the compare tool is inefficient and does not show all relevant comparison data when comparing a board to the annotation image. If the only difference between two versions of a board was one component being moved on the top side with a new trace and via, for instance, using the ECAD Validate tool for an image compare will just show that the "Top Pin Pads", "Top Via Pads", and "Top Routes" layer have changed. We want to be able to select the "Top Planes", "Top Conducting Figures", etc. (other relevant items on that layer) in the left hand toolbar so that we can see that those shapes are common between both boards. See pictures for the context of the situation. A separate issue I wanted to bring up was that if objects in the transaction list are selected for multiple items (i.e Top Pin pads AND Top Via Pads), the preview transaction item icon no longer becomes selectable. Th
Ability to create a new manufacturing assembly buy assembling 2 or more manufacturing assemblies and maintaing all the information from the original manufacturing assemblies.
For some parts, it is helpful to have tangent lines on. For other parts, those tangent lines are confusing and should be turned off. But there are some parts where some tangent lines are needed, but some should be off. In the View Properties window, there are options to turn "All Tangent Lines" on or set them to "None". There is also a "Selected" option, but that seems to only work on a part basis. I am suggesting that there be an option to select tangent edges to be visible or not.
Modeling has a great customization facility, that ca be used to customize the Structure Browser, to show up the user both MODEL NAME and INSTANCE NAME. MODEL NAME more often used as a NAME or REFERENCE, while INSTANCE NAME is rather a DESCRIPTION, while in some circumstances (not shared parts) INSTANCE NAME can be MODEL NAME. When PDF 3D are produced to be used by non-Modeleing educated people, it would be nice they distinguish in the Adobe Reader Structure Browser both these 2 definitions. MODEL NAME can help them to refernce parts while INSTANCE NAME may help them to locate the part in the assembly.Currently only standard eDrawings production is able to show both MODEL NAME and INSTANCE NAME. PDF 3D and PVZ not.It would be great that all viewable production could be customized to adapt the Modeling Structure Browser appearance.
1 - Make a one button option to delete all orphaned dependencies2 - Make the new Creo trash icons larger and not so close to the lines. By clicking on the lines, it takes you away from the menu.3 - Allow the option to filter for orphanes dependencies to be viewed at the top level assembly only. Because, by breaking all orphaned dependencies, you are actually modifying other files that have those orphaned dependencies. You may not have access in the Windchill system. Just like you can view the top level for a layer, here too. We would just like to break the dependencies for this specific file. The others will have to be dealt with in their file.
We would like to measure the distance between exploded components/models using DISTANCE. ANGLE works fine, DISTANCE gives the distance from the unexploded state, even though the model is exploded.Update: this Product Ideas has been marked as a "Duplicate". Anyone interested in supporting this idea should add their vote here: Make Measurements reflect explode state values
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.