Recently active
In Creo: Put the Event Manager, or another Windchill Status monitor in a more obvious location When using Creo linked to Windchill users do not have a readily available way of knowing the status of the Windchill link to their Creo Session. The best example of this is when a Creo check-in fails. The failure message only shows up in the messages at the bottom of the Creo page and the well-hidden Event manager. It would be a benefit for troubleshooting to have that fail message in an obvious place. Possibly give the users the option to put the event manager, or some other Windchill dashboard, front and center so they can monitor the status of the Windchill connection to their Creo session. Bob LohbauerMedtronic
Export dxf direct from 3d models without creating a Creo drawing. Creo 3.0 has this option, but it is creating a facet model only, exporting to many lines which can not be used in programming a laser cutting machine for example.
I'd like to show an assembly in sequence as it would be manufactured, with each new sheet adding a new BOM item and it's corresponding Balloon. This is done by showing a different Simplified Rep on each view/page (Step 1, 2, 3...)Rather than fixing the indices (Item Number) for each part on every Simp. Rep., can I fix the Index for items across all Simplified Reps?In addition, can there be a way to add the respective balloons without needing to include a hidden BOM on each sheet?
The length of the wire of a spring (constant or variable) cannot be measured in Creo 2.0.However, this should be possible.The workaround to calculate the length by dividing of volume by cross section or to measure the length by redefine the sketch in a quater circle is complicated.
Hi PTC, i am giving some idea about dynamic probe. 1. If there are two result windows open and we get the dynamic query at any point in first window, we can't get dynamic query at same point in another windows. There must be a provision to manual enter the point coordinate to get result value. 2. There must be toolkit API to get the result value of given coordinate. 3. if we save some result file (.rmd) with dynamic probe values and reopen that file again, All dynamic probe value must be visual as like before. Thanks Shashi Kant
When switching between windows while in Simulate mode the performance is poor. This is because the moment you switch between models that Simulate creates simulation geometry which affects the loading. The problem is that the simulation geometry is cleared when you exit the window. This means that the simulation geometry has to be re-created when you switch back to a component that has in fact previousmly been loaded.This is less of a problem when working with Simulate integrated with Creo Parametric, as you can close the Simulate Application, and switch windows in Creo Parametric. However, in the case of the Simulation Standalone Application this becomes a bigger problem.What I would suggest is that a type of smart regeneration be implemented that caches or keeps already loaded simulation geometry in session.Otherwise, an improvement of the performance when switching would also be beneficial.
Other than Creo, every 3D modeling software I have used has the ability mirror components in an assembly. This is done by selecting a mirror components command, selecting a mirror plane, done. I found all kind of "chatter" on the PTC websites and on bulletin boards, etc. I've looked for at least an hour and still no intelligent solution. This needs to implemented ASAP!
In Creo Mold Analysis, While giving different step animation speeds in Melt front times and other features, Please add option to replicate the same animation speed in result PPT too.
Currently, depending on which tab Annotate or Sketch, or on which function, sketch, note, etc., certain entities cannot be selected for references.For example, when creating a note, it's leader cannot be attached to a symbol, only the model object or sketches. However, the note cannot be related to an object type sketch, only to other notes or symbols.Also, when sketching, axis, geometry, datums cannot be used for functions like mirror.Why not just make all entities, object, draft, sketch, symbol, format, -EVERYTHING- selectable for everything else? Why add extra code to differentiate?PTC, please make all entities selectable as references.
Please add the ability to select one or more components and Isolate (hide) all non-selected components in Assembly and Simulation mode. This will reduce the time to apply Simulation Interfaces, Springs, Features, and assembly constraints. This would be similar to the Isolate command in Simulate Component Display in the Results Definition Dialog box This idea is to quickly and temporarily hide components that are in the way without using layers or reps and to redisplay them again with in a second or two using the unhide command. Thanks, Don Anderson
The description column in the Information Window in Compare Parts by Feature is only 26 chars wide, while my information is much longer than that. So I get the following:DIMENSION VALUE: from 6.80with no "TO" value. This makes the information worthless. I put a ticket in, and was told that there is no way to change the width of the column. The log file that is saved is also truncated.
I would like to see the ability to split the model tree to see two different parts of the model tree at the same time (similar to MS Word and Excel split screen). I am often working in models with a 10 page tree and want to refer to datums at the top when working at the bottom. Similar issues occur in assemblies when assembling apart with datums.
When a featurefails (such as a round) you are in the following situation:If you select the failed reference and click on what you want to replace, Creo delete all references (see next picture)Hence to resolve the failure you must remove the failed reference (see next picture) and select a new one by holding down the CTRL key.This is, of course , not a replacement of the old reference (so all the children of the old missing reference continue to fail). It would be interesting to unify the behavior of a lost reference selection to what happens in the context of a redefinition of a sweep in which, if I select from the selection pane a lost reference (ex. a trajectory) BEFORE selecting the geometry on the model, the newly selected reference substitues (replaces) the old one (see next pictures).
Back in Wildfire days, it used to be possible to have tangent edges show as dimmed in shaded view.Apart from looking nice, this allowed you to simultaneously tell whether an edge was tangent or not, and also check all your edge lengths between rounds and other surfaces when constructing complex surfaces.Since Creo, tangent edges in shaded view can either be completely off, in which case you can't see edges lengths between tangent surfaces; or 'hard', in which case you can't tell the difference between a tangent and non-tangent edge - unless you work in a wireframe-type view, in which case you can't see the shape of surfaces.Yet another piece of lost functionality in the downgrade from Wildfire to Creo... please can we have it back? I can see no reason for making this feature non-functional!It's official too:https://support.ptc.com/appserver/cs/view/solution.jsp?n=CS106133
Hi PTC, Please add ability to Component Repeat Placement to Include Duplicating Simulate Features like Contacts, Ground Springs and Preloads! How many times have you needed to repeat the placement of a component in an assembly. Wouldn't be nice if you could have the simulate features referencing the current component duplicated and attached to the placement of the new component placed in the assembly while your using the repeat command? Imagine you have 3 or more plates that you need to bolt together. This requires you to use solid models of the screws, studs, washers, nuts and bolts and you currently have to defined each contact between each part manually. This is a lot of wasted time if you have a dozen or more fastener locations to deal with. With this enhancement you would place the first set of components in one fastener location, define the simulate features like contacts, springs, preloads, loads, etc. and then while using the repeat command or pattern command you
Its blooming obvious really, and why PTC have never implemented it on ProE, then Wildfire, then Creo 1,2,3 I've no idea. My £50 Mac CAD package adds a sensible value fillet according to a value I choose in sketcher. Creo just scatters on totally random values and you have to go around cleaning them up and putting in values and making them match manually.So, here's the brilliant 20 year old CAD idea, when you select fillet in sketch, you get to type in a value, and, I think you might guess what's coming next, when you click on two lines to put a fillet between, it puts that value in, and on the next pair, this continues until such time as you type in a different value.I know its not a new idea. It really basic, but frankly a $X,000 CAD package really should include this shouldn't it?
PTC, Please Add Ability to Creo Parametric Simulate to Copy Components and or Sub Assemblies with related Simulation Features from one Assembly to Another Assembly and allow you to specify new feature references using Paste Special > Advanced Reference Configuration Include Simulate Features. Say you have multiple assemblies and you have a common load fixture that you use to apply load in your assembly simulations. Wouldn't be nice if you could set up one of the assemblies with the load fixture and all of it's connecting fasteners, idealizations, contacts, materials, etc. and copy this portion of the assembly with all of its simulation features from one assembly to another assembly and be able to specify the new interface references for the mating components on the new assembly along with the simulate feature(s) references? Think of expanding the Paste Special command Advanced Reference Configuration to include Simulate Features like all referencing fasteners, contacts
PTC, Please Add Ability to Creo Simulate to Copy Simulation Features From One Part or Assembly to Another Part or Assembly. This would allow us to copy contacts, fasteners, and etc that have all of their settings filled out from one model or assembly to another model or assembly without having to refill in all of the information again. Thanks, Don Anderson
Bonjour,il serait intéressant de disposer d'une commande permettant la délimitation d'une partie d'un pdf inséré sur un plan. Actuellement il n'est pas possible de délimiter une zone précise du pdf après l'avoir placé sur un dessin. L'opération est réalisable en passant par un document word sur lequel on insère le pdf, puis on rogne le document pour obtenir le résultat désiré mais la succession des opérations est trop longue.version Creo2
The new rmb menu icons are not intuitive and new and seasoned users alike are getting very frustrated at having to mouse over icons and wait for the text to pop up, where previously, the commands could be seen at a glance.Yet another drawback from PTC glomming on to Microsoft's poor vision of office functionality to make the menus more familiar "looking", but to the detriment of the function.An easy way to remedy this would be to allow the text to be shown next to the icon:PTC, please allow text to be shown for rmb menu icons.
We created https://www.ptc.com/appserver/cs/view/case.jsp?n=13254764 which may not be viewable to all customers. The idea is to provide a mechanism to control what is populated into the attributes table when selecting children in the model tree. The current downfall is that if you select children on a large assembly, you can experience a long delay before the table is populated and Creo View is unresponsive at this time. (Note: I'm assuming the delay is due to the population of the attribute table...PTC development needs to confirm.) It would be nice to a solution where I can select/define which columns of attributes automatically populate into the table when selecting objects in the model tree. There is very nice functionality within that attribute table with copy functionality and enabling pasting into Microsoft applications for future report and interrogation. I would like to take advantage of it. Microsoft didn't like the 7000 pages by abou
PTC, Please add the ability to suppress surface regions in Creo Parametric Simulate. There are times when you want to break up a surface to put a load on a portion of the surface for one analysis and also apply a contact on the same whole surface of the same part for another analysis. Thanks, Don Anderson
Relative to the main unit system, if you want to change the units of the load to another unit will be required unit conversion.In order to prevent the mistake, I want you to automatically numerically After changing the different units are unit conversion.After entering a value in the numeric field of the load, but it seems it is unit conversion by right-clicking, is less well-knownNot There are I think whether current situation.Please consider.主要単位系に対して、荷重の単位を別の単位に変更する場合は単位換算が必要となります。間違いを防ぐために、別の単位を変更したら自動的に数値が単位換算されるようにしてほしい。荷重の数値欄に値を入力後、右クリックで単位換算ができるみたいですが、あまり周知されていないのが現状かと思います。ご検討願います。
PTC, Please Add Ability to Select a Component in Creo Parametric Simulate and Show All of the Dependent Simulate Features for the component that's selected. This could be an enhancement to the Reference Viewer and also a Right Click on the component menu with a Info command window to show what simulate features are dependent to the component. I have a component in a assembly where I want to find all of the Creo Simulate Contact Interfaces that reference this component. From what I can tell, Reference viewer unable to display the Creo Simulate features that are dependent on a particular component. Info by model doesn't show the info either nor does info simulate. Please add this functionality so when one person needs to replace a component in a assembly they can identify what simulate features need to be re-routed to the new component. Thanks, Don Anderson reference: How to select a component in Creo Parametric Simulate and show only all of the dependen
Currently, family table instances are sorted by ASCII code during the replace function:INST1INST10INST1001INST2INST201Please allow the option to enable a natural sort which would put the instances in numerical order.INST1INST2INST10INST201INST1001
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.