Recently active
If you scroll down in the menu tree to find a feature/component when you go into relations the menu tree scrolls back to the top. This is very frustrating, I scrolled down to find what I wanted to write relations on then I have to go find again. Please fix, it did not work like that in Wildfire 4.0
Now it's impossible to show safety factor on a surface of model in post processor of Creo Simulate. Of course you can calculate it but it's nonvisually. I will give an example what i mean (the picture from Ansys). In my understanding it's so easy to realise in Creo Simulate, please add this functionality.
From time to time we put MIN or MAX dimensions on drawings, for example an included angle where the radius cannot exceed a certain value but can be as small as the fabricator would like. The issue is that we want to keep the model at nominal, and don't want to change the model to be our MAX or MIN, especially since most of our suppliers build tooling off the model (and may or may not always look at the prints early in the phases). We'd like to find an easy way to show ONLY the MIN or MAX but not both. I learned from a PTC ticket that this is not an available feature in Creo currently. I'd like to see these options in the drop down in "Tolerance Mode" section of the Dimension Properties: Show MAX only Show MIN only This way, you can still define the limits but only show one or the other, to keep the drawing cleaner.
existing issue: 1. hole table update, this function is very cumbersome, every thing is back to default when you update table, include merged cell ,decimal places, lable position . 2. hole table cannot update automatically I want to know why there is no improvment from WF to CREO 3.purpose: you can reference SolidWorks 2016 Hole table ,this is perpect.if can use excel type table is very good.this is the table before update.this is the updated tableeverything back to default .
I've been noticing lately that there isn't great support, mostly in terms of the Options, for companies where the same users work in Metric and English. These users don't want to run mapkeys each time they switch between working in Metric and working in English. Furthermore, even if they are willing, they would likely forget and then mess up on the models they are currently working on.The below two options just became an issue for us this past week. I'm sure there are many more that I'll add over time. The main request is for PTC to come up with a newer option structure that can help support these options either at the model/format level OR be robust enough in the config.pro/supdrawing_setup_filedefault_dec_places
Right now in Creo direct modeling 19 there is a option to go from the structure browser to windchill. the "View information" button. This action redirects you to the document information in windchill.It would be an enhancement if there could be a button added when right-click - "INFO PART" , to go directly to the related part of that document.This would save us a lot of time because then we don't always have to go to the document first to see the info we need.Regards,Bram
Due to the many issues that occur from orphaned dependencies, especially when doing a SAVE-AS to an assembly that has those orphaned dependencies, it would be great to have better support for this:A 'Break All' option to break them all at onceShift to select multiple references at once and then RMC to break themReporting in the Notification Center when they are created or when models have themModelCheck reporting and ModelUpdate to break them
When one creates a curve from ibl file with Get Data > Import and then uses this feature to create some other features that depend on this one, after this feature is updated to a new source (via ATB update and change link), all children will lose reference. So in effect the update to a new source of this feature is a destructive operation and doesn't really represent a redefine of a feature. The internal feature ids are recreated which causes all children to lose reference. This behavior renders this kind of feature useless since the references to children cannot be maintained. Why such a behavior was implemented in the first place in the software which is based in parametric modeling is quite strange. So, this "product idea" is a request to make this feature actually work as it should and as other features in Creo work and that is to be able to retain connection to children after redefine.
When you create an Inheritance Feature, all the entities that were contained in a layer in the base model, in the inherited model are all visible and not contained in any layer. Moreover the user is not allowed to put any feature contained within the inheritance feature in a layer (CREO warns you that "Cannot select feature from Inherited model in this context").This affect negatively the view management display (expecially in drawing mode).It would be usefull if the inherited model could inherit also the layer structure in some way (as a subnode layer, for example).
When selecting the layer tree of an individual view, all of the layers are turned on. I would prefer that the layer status stays the same as the drawing layer status until I unhide a layer. It should also remain drawing dependent until a change is made.I mostly modify the layer status of a view to show one or two items in that view such as a cosmetic sketch. When everything is reset, the drawing layer status, that has already been set as needed is lost.
Would like to be able to use multiple cycles of EVALGRAPH in combination with trajpar similar to the cycles which can be used using trajpar with sin.The graph entities should be able to be multiplied along the trajectory.
In a drawing, for a shaded view, give the possibility to define a layer state different from the model driving that drawing.For the moment, for a shaded view, the layer state always follows the model's layer state.See https://support.ptc.com/appserver/cs/view/case_solution.jsp?n=CS43026
It is not possible to directly display a Datum Axis in a Half View if the axis lies on the half view reference planeThe workaround suggested by PTC:Change the View Visibility to: Full ViewShow and position the model datum axis annotationSwitch the View Visibility back to: Half ViewIt would be nice to directly be able to show the axis on a half view.
There is no API to find global clearance in Creo 2.0 using toolkit. We know API ProFitClearanceCompute to calculate clearance between two components only. We are looking for something which does it for entire assembly.
It must be possible to call out the repeat index parameter value (as by &rpt.index for example) in a drawing note of PTC CREO.
This is a new format for additive manufacturing supported by a consortium of big companies. Additive manufacturing is being called the next industrial revolution, and Creo Elements/Direct Modeling NEEDS to be a part of that.
Release 190 introduce MERGE CONFIGURATION, that is a great function that customers were waiting for.But in 19.0 release if you merge 2 configurations, drawlist and camera informations of merged configurations are lost.If configurations are used only to show some elements, and customer needs to merge several configurations, there are no benefits by MERGE commands.So my proposal is: Add drawlist and camera information to MERGE CONFIGURATION
I have a suggestion that plunge milling be improved in NC. Plunge Mill manufacturers suggest that the tool back off the cut after plunging, then retracting prior to taking the next plunge. This does not appear to be possible in Creo 2.0, and from what I understand 3.0 cannot do it either. Tools would not stand up to the current method of being dragged back across each cut, so I cannot see a use for creating a plunge milling sequence with the available sequence definition.
I need to have a steady center curve for building sweeps. To get this it is necessary to have center points of all the sketches that are chained together to build the sweep.Presently you have to use the Behavior Modeling extension for the center point ability, and it is very tedious.1) Extrude the sketch2) Use the Analysis function3) Save center of gravity point as feature4) Capture this point in the extruded sketch5) Repeat this for every center point neededWhen you have upwards of 20 sketches included in the center curve for a sweep this is very time intensive.
Problem: extension lines for diameters and radii can be, not off in drawings. This one gets confusing drawings for manufacturing that are not standard for handicapped. The problem occurs when each produced diameter / radius measure. When shown the diameter dimension extension lines must be separately displayed., But also can not be clipped then. Proposal: extension lines even when produced diameter sizes produce only via context menu - but they should survive over the arrowheads. It is good if you can also clipping the extension lines for diameters and radii and they can also hide again / off would be. The uploaded images are once the radii / diameter created using Pro-E 4.0, Standard-compliant, as it should be. And created with Creo 3.0, not reach compliance. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Hello,It is very easy to load a 3D file from windchill to modeling with some lisp commands, but loading a 2D (MI-file) isn't possible.If you could load 2D files with lisp you would be able to automate many things that always have the same procedure.Thanks
Actual there is no automatic way to find out the NC-Sequence which causes the error: "Output on profile failed. Please, check CUTCOM setup." When there are a lot of sequences, it is a big task so find out the failed sequence. It would be very nice to have an automatic method to find this. I refer to call 13127016
Curve pattern is actually unusable for us: trajectory is moving for each instances along the profil....Wee need a real curve pattern wich allow to follow curve direction & the instance must follow the curve.To understand, try to do a pattern along a closed curve with 2 circles...Thanks
I would like to see an option to Output all Operations under the Save a CL file tab. Many projects have multiple operations and each operation may take a few minutes to output. In order to efficiently output all of them, you need to stay attached to the computer and output each one individually. I would use an "Output All Operations" button most every day.
It would be nice to have the ability to click on the diameter box and change to Radius. Also, it would be nice to click and change from (in.) to (mm) in this display box. Posted for a fellow user.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.