Recently active
in annotation you can only create a flat view of the entire part. it's not possible to work in steps.i would like a possibility to get a flat view with only the lips i have selected.
Since Creo 3, on a drawing, when you select Dimension and then choose your first reference, a preview of the dimension is attached to the pointer. If you press CTRL to select additional references, the preview of the dimension updates, based on the selected references. But, the preview of the first reference stays visible and will be shown (almost) on top of the pointer and so it's hard to select a second reference. This is quite confusing; at first sight it's not always very clear which reference was chosen exactly.It should be better to:- Let the preview of the dimension disappear from the moment CTRL is pressed (and, of course, show the corresponding preview after the second reference was selected)or- dynamically update the preview when you hover over the new selection(s). (Altough, this might be a little bit too buzzy)
One should be able to replace an external copy geometry by instance, that is:If the source part for the external copy geometry (ECG) is family tabled, than one should be able to right click the ECG feature in the target part and "replace". The functionality already works if the target part is family tabled (by having a reference model column in the family table) so it should also be able to work if the target part is not family tabled. Currently, if one points the ECG to a different model (even if it an instance of the current source model) one loses all of ones references and one must re-pick them and fix all the referencing features. By extension, this same functionality should be available for use with pro-program, being able to replace the source geometry by using a parameter for the model name of the source part, just as one does to programmatically replace a component in an assembly.
Please add the ability to add multiple Motion Axis Constraints to Snapshots when defining a snapshot.It's very time consuming having to select the command "Motion Axis Constraint" then only being allowed to select one motion axis and have to repeat 20 times.Also Highlight joint Axis on screen when Selected under the Constraints Tab while defining a snap shot.Thanks,Don Anderson
It would be nice to have the ability to define transparency in addition to default system colors.With this opportunity it would be possible to have transparent surface representation besidenon transparent solid geometry. With this constellation it would be easy to find out if thegeometry is a solid or a surface. If there are lots of surfaces inside the model it would behelpful to as well to find the correct surface for your construction.Additional to the transparency idea the edge display in shaded mode could be improved which isa related idea with the same scope in this community :Idea 7358 - Ability to have different edge colors for surfaces in shaded view
To improve the identification of surfaces in shaded view it would be nice to have differentedge colors for surfaces in shaded view as it is in wire frame mode.With this opportunity the user would be able to find out if the geometry is a solid or a collection ofsurfaces. If the edges have different colors depending on the status if the surface is merged to the next surfaceor not it would improve the work with surfaces in shaded mode.Additional to the edge color idea the default system color with transparency for surfaces could be improved which isa related idea with the same scope in this community :Idea 7357 - Ability to define transparency for default system colors
Hi,I would like to have a feature that would allow colors assigned to a part/assembly to appear in the 2D drawing. This would be helpful for clients to see parts that are part of a large assembly, which might otherwise be difficult to spot in a 2 D Black and white drawing. Thanks !Cheers,Avinash
With the config.pro option 'measure_auto_replace_mode=yes', when one want to measure distancefrom 1 vertex to several second points, only for the first of the second points, the CTRLbutton is needed and for the rest of the 'second points' , the CTRL button is NOT allowed.The need of the CTRL button for measuring does not make sense so CTRL button shouldnot be required at all as it was in Pro/ENGINEER Wildfire.
3D Documentation -Create drawings by transfering Doku Levels - the distance between the views in Annotation should be adjustable. So far, there is no possibility. It must be reworked manually.
3D documentation -Create drawings by transferring Doku Levels - view label should be adjustable - there is no setting for the view label a default name is created.
3D documentation - Dimension settings for lines, text, tolerances .. every value should be set individually. As for the dimensioning in Annotation.
The current units for strength values are not common for engineers.In the real world N/mm² is used instead.
This is a 3 part product idea. 1. Add the ability to turn layers on and so one can hide construction surfaces so as to be able to select solid model geometry surfaces for Strain Vector Plots. 2. Add the ability to view vector strains only on the outer surfaces or surfaces in direct line of sight. (option to turn off vectors inside the part or on the other side of the part) 3. Add the ability to hide items selected in the selection window so one is able to select the base geometry for which results are needed more easily. There are many times when you want to use Strain Vector Results in Creo Simulate to aid in placing strain gauges on physical product being tested. Currently it very hard to view the strain vectors on the surface nearest to you that you are viewing. Thanks, Don Anderson
It would be handy to select multiple references using the find tool in sketcher. The example is when in sketcher and you need to add references, lets say points as the most practical example, you can add all the necessary points at one time. I think this could be limited to a few object types, but useful overall. Points, CSYS, Curves are the items I would like to see at a minimum.
Please add the option when creating surface regions to have them spilt into separate segments. In the part below one wants to put a constraint on one side and a load on the other side. Currently you have to create 2 separate surface regions. The first surface region goes all the way thru the part with no option to limit it to just one side of the part. This would reduce the number of surface regions that need to be made. Thanks, Don Anderson
When 3D geometry in the area of an already defined bolt circle is modified (e.g. angle between the elements) and the view in Annotation is updated, all the already defined dimensions and the orientation of the center lines should be updated correctly. Currently those modifications force the user to redefine the bolt circle in Annotation.
Guten Morgen,in Creo vermisse ich schon länger die Möglichkeit, ein Muster wie folgt zu erzeugen:- Mustertyp: füllen (skizzierte Kontur)- Anordnung: Rechteck (Abstand x <> Abstand y)Uwe Jung
Need to constraint or fix the distance between two view.. For Example : Please find below snapshot for reference I had modeled a shaft of 100 Dia and 1000 mm length and placed same in drawing with scale factor of 0.15 but when i reduced it size to 100 mm length views get merged. My concern is that views should maintain some specified horizontal distance between them and should not get merged.
I would like the option to align views using datums.
Currently it is not possible to apply the Solid fill option on Offset Cross-sections (only available for planar cross-sections).It would great if this option was also available for offset sections.An example of where this would be useful is in the case where a Full(unfold) cross sectional view in a drawing is used to clearly layout the internal workings of a complex design, like a gearbox/transmission.Here you could fill each component being sectioned with a different colour, creating a clear and useful view of the design internals.For a workaround one could of course apply hatching with really small spacing, but this drastically affects performance, especially on larger more complex models.
Bonjour,Il faudrait rendre possible la mise en plan avec "ombrage avec réfléxion".Ceci permeterait de faire de belle presentation aux clients.MerciSalutationsFabio Giannotta
Currently only 2d sketch can be rotated or swiped to create a surface or solid or cut. Please implement creation of geometry by sweeping or revolving of a 3d curve.This function is available in Catia for many years.
it would be useful to create a mirror mesh within CREO Simulate (in a symmetric part or assembly) even in case of non-symmetric loads, you could have a more homogeneous result.
If you cut your model to use symmetry in CREO Simulate, also in the result windows you will see half model. It would be nice if the software "mirror" the sesults to display the full model within the result windows. A similar behaviour is implemented, with a different aim, in the "Visual Mirror" command, located within the "In Graphic" toolbar, when you create or edit a style feature.
Because the publish geometry feature only shares geometry as it exists at the end of regeneration, it should always reside in the footer to make that clear.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.