Recently active
Actually it is not possible to activate in the same time "Auto Cutline" and "Tool center curve"This would be very useful to machine closed pocket to:- start at the center of the pockect using the point- avoid retract on the contour of the pocket thanks to the "tool center curve"Actually the solution is not to select "Auto cutline " and to create a projected curve instead which is more work to do
1. Add ability to select a part or assembly feature while in Creo Parametric Simulate and edit it's definition. It's very time consumming to edit feature definitions on parts which were not created by you just so you can get it to mesh. 3. Add ability to select feature in model and have it highlight the feature or rightt click and go to that feature in the model tree while in Creo Parametric Simulate. 2. Add ability to mesh D1 x D2 conic round with values 0.5 for sharpness "0 thru 29" for distance one 40 for distance two where the round transitions the inside corner of a rib going into a round boss. 3. Give more detailed description of errors while meshing... "Problems were encountered while preprocessing the features for the highlighed surface. Source AutoGEM" Sometimes the the feature not highlighted and when it is where on the surface that is highlighted is the issue. The whole surface or on
With the selection filter set to "geometry," user should be able to select a visible surface by clicking on it, even if there is an edge hidden behind the surface under the cursor. Current functionality is to select edges whenever possible, regardless of how many surfaces are in front of that edge. The edge could be completely hidden from view, behind a huge surface that fills the screen, but if it is under the cursor, it will be selected instead of the surface. This current selection functionality could be enhanced by prioritizing selection by z-depth, where the geometry closest to the screen is selected, since this is what users typically expect.
With the old Drawing note system, a mapkey can use the EDIT > PROPERTIES command to edit a note. However, with the new Creo 3 system, the only way to go back into a note is to click on it. That action can not be reproduced with a mapkey. Therefore, any changes to a note can not be done (unless you try running trail files).
When creating a cure through points in IDD you do not have the ability to define tangent end conditions as you are in Creo Parametric.Can we add the ability to define tangent end conditions to curves created in IDD?Creating A Curve Through Points In IDDCreating A Curve Through Points In Creo Parametric Modeling
Our config setting uses one of the old blue schemes for the background in Creo 3. However, this drowns out the blue that is used to highlight overlapping geometry in the Flat Pattern Preview in the sheetmetal module. It would be great if we can customize this color without changing the background.
Creo simulate, pro/mechanica structure, it's alway been the case that when you define a fringe or contour result window, the legend levels are defined automatically.When you're doing a project, with the umpteenth variation of your subject, you know that you always want to use a typical range. Still the only way is to generate the fringe plot and edit the levels afterwards, after which simulate regenerates the window, which takes time.Especially in animatred fringes, with many frames,. regenerating the animation takes an enormous amount of time.In creo 3.0 this happens twice, once for the maximum level value after editing, once for the minimum level. Please provide the option to define the legend levels in the definition window.
File location parameter for showing file location path in drawing.
Ability to create parameter assocciated to dimension.It could be usefull in the MBD, to stroe complementary information as for exemple:ppm target for the dimension (or Cpk and cc)Result of the measurementStack up result analysis.Robustness class of the dimension.
Implementation of config.pro "UI_THEME" in Creo Parametric for better visibility of pushed icons and position of scroll bars
It would be nice if the default "Creo Files" filter could be modified or if a "User Defined" default filter could be defined. I work with stp files a lot and it would be nice not to have to change the file type filter all the time and instead just add it to the list of "Creo Files" which is the default.I can imagine that people that work a lot with autocad files might like the same thing for .dwg files for instance.
Dear Sir,Recently my customer has come across the below small requirement.1. The file path should be printed automatically on the drawing, once he add the parameter in template.Since this facility is manual at this moment. Please add this as a parameter in the template for automation of this small.Best RegardsAnil Pagar
Currently Windchill is unable to delete a selected group of objects if one of those objects is found to be in a workspace or tied to some process or connected to any hierarchy. If an object in the list is found to be in a workspace, selecting the "medicine box" in the event manager will not necessarily resolve the issue because the same object could be tied to something else within Windchill. There should be a way for Windchill to delete all of the selected items that are free and clear of any relationships or processes instead of not deleting anything in the selected set of objects due to one or more being tied to something else.
Add a RMB "zoom to" in the Find collection results.
Add a config.pro option to switch between "define simple thread" and "define standard thread" as standard option while creating a cosmetic thread.
1. Allow double click on results window legend min and max values to change cut off values. 2. Fix issue of Results Window Legend not retaining Upper and Lower Limit Values that were set (cut off values) for the following changes to the results window... - When hidding or showing components in the results window for assemblies the legend resets the limit values - when changing from vm to maxP stress the results window legend resets the limit values that were previously entered
Add ability to save simulate results windows Templates for design studies that have multiple load cases where all or some of the cases are being shown in the results windows. Imagine doing multiple iterations on the beam and needing to show all four results windows for each design iteration. Currently you are not able to save a template containing all of the view shown below to be use for future runs where a part may be changed in the assembly. All 4 windows (load cases) need to be shown for reporting purposes. This will help address the following error message..All of the windows for inclusion in the template must be from the same study directory (Error Message)
In PTC Creo Simulation, it would be extremely advantageous to be able to specify run settings on a design study basis. By doing this one would be able to specify a unique previous mesh for a number of studies. Then one could run a batch file over the weekend for one model with multiple mesh configurations.Also, one could specify the design study file location on a design study basis. This would allow a local directory to be specified for design studies currently being run and another location for archived results when local drives become full.David
Currently one can only used results of a previous steady state analysis as initial temperatures for a transient thermal analysis. One can use the results of a transient thermal analysis as input for a structural analysis but not for another transient thermal analysis. Therefore, if one is determining the temperature distribution in a valve and the flow conditions change, one is out of luck as one cannot either vary the convection coefficient with time or start a new analysis with a different convection coefficient using the result of a previous analysis.
I'm using Creo Parametric 2.0 M120.In a medium-large assembly (5800 parts) if Smooth_Line option is enabled, it takes a long time to make an offset cross-section (+/- 5 minuts).If Smooth_Line option is disabled the same cross-section can be made in less then 1 minute.I have made tests in some Hardware scenarios, the worst machine configuration was an "Intel Core I5 - 4G RAM – 1G graphic card" and the best machine was an "Intel Core I7 - 32G of RAM – 2G graphic card", in both machines the results was similar.Its important to me to work with Smooth_Line enabled but, it need to be faster.
Currently only one option to automatically create resulting objects is available when change a notice is being created.This is the revise button.This creates a new revision and in our workflow sets the resulting newly revised object back to In "Work status" from its "Released" status which means the previous revision is still the Released revision until the change has been completed and then the newly revised object gets upgraded to "Released"However if I want to create a change that will have a minor effect on an object such as a spelling mistake on a drawing or an incorrect mating in an assembly etc. it does not warrant a full revision it makes the transition by iteration for example V 1.1 to V 1.2 instead of V 1.1 to V 2.1.This is not currently possible. As there is no way to up-iterate then no resulting object can be created. If the Object in question is at"Released" then the change is happening to a "Released" Object (in our system no one can check in a modified released part). It
Avoir la possibilité de choisir le style d'affichage (ombrage, ombrage avec arêtes, lignes cachées, sans lignes cachées, filaire) différentiellement pour chaque composant d'un assemblage dans une mise en plan. Cette fonction est disponible dans un assemblage (cfr 'Assemblage.jpg') par l’intermédiaire de l'onglet 'Display' du 'Gestionnaire de vues' (cfr 'Gestionnaire des vues.jpg') mais pas dans la mise en plan (cfr 'Mise en plan.jpg'). Have the possibility to choose the display style (shading with edges, shading, hidden lines, no hidden, wireframe) differentialy for each component of an assembly. This function is available in an assembly (cfr 'Assemblage.jpg') using the tag 'Style' of the 'Manage views' (cfr 'Gestionnaire des vues.jpg') but not for drawing (cfr 'Mise en plan.jpg').
Would it be possible to create surface and volume regions at the assembly level so that they are not reliant on them being created at the part level.This would be useful where you want to create a surface or volume region that splits across multiple parts in an assembly.
Derzeit ist es nicht möglich, Geometrische Produktspezifikation (GPS) – Dimensionelle Tolerierung – Teil 1: Längenmaße nach ISO 14405-1:2010; Deutsche Fassung EN ISO 14405-1:2010 zu erstellen. Problem ist bei PTC bekannt C12507314, SPR 1909487; SPR2119259 aktueller Stand der Norm wird angehängt. Die Symbole sind in den Tabellen 1 - 3 auf Seite 19 und folgende dargestellt. Beispiele wie das in den Bemassungen auszusehen hat, sind auch in der Norm dargestellt. Bitte alle Möglichkeiten, auch die Darstellung von eingeschränkten Teilbereichen berücksichtigen. Im Anhang A sind Proportionen und Abmessungen graphischer Symbole dargestellt
When importing a step file or opening a native file, Creo splits a single surface with G2 discontinuity into multiple surfaces. I would like an enhancement of a config option to NOT split the surfaces.WF5 and Creo 3.0 are the ONLYsoftware that will split the single surfaces into multiple surfaces. This normally wouldn’t be an issue, but when we bring this geometry intothe Mold Design Extension, all those extra edges and vertices cause geom-checks and splitting issues.Here are some examples of "Other" software importing the same file. Note the multiple surfaces in the PTC products.Here is the file brought into WF5Here is the file brought into CreoHere is the file brought into SolidWorksHere is the file brought into NXHere is the file brought into 3D Evolution
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.