Recently active
You’ve probably heard enough about smart, connected products and the Internet of Things (IoT) to realize this is not a passing trend.If you haven’t seen the recent figures, there are already more “things” connected to the Internet than there are humans on the Earth, and it is expected that 80-100% of all manufacturers will be using Internet of Things (IoT) applications by 2025 (see the McKinsey Global Institute and Cisco reports).But you may not know as much as you’d like about IoT technologies, or what these advancements mean for the professionals – like you – who will be designing or developing this next generation of products.At PTC Live Global, June 7-10, you can get a greater understanding of the role you play in a smart, connected world, AND start preparing for it – all in the same venue where you’re building your technical skills and gaining best practices to enhance the products you currently design and develop.Through breakout sessions and hands-on PTC University training with
Ab dem 17.03.2015 werde ich bei Continental in Frankfurt eingesetzt sein.Voraussichliche Dauer: bis Ende Juni 2015.
From a design point-of-view, what would be the difference in your margins of safety using symmetry/mapped meshing vs a perfectly coded software with 0% error?
Did symmetry and mapped meshing resolve the problem?
Agnes,Thanks for keeping us posted. I couldn't locate the SPR in the Knowledge Base (as shown below).
Because we’d like to know what you think about PTC Live Global, we’ve organized a contest where you can have fun and win prizes while sharing your opinions.Each Friday, from March 13 through May 15, we’ll ask an “If you” question. Those who respond will have the opportunity to win a $200 gift card. There will be 1 winner who will be chosen by the rest of members of the PTC Community.These are the contest rules:To participate, you must join the PTC Live Global Group.You can respond as many times as you want to each question and/or answer as many questions as you wish.The winner will be decided based on the number of likes his/her answers receive from the rest of the members of the PTC Community.In case of a tie, the winner will be selected randomly.The prize will be a $200 gift card.Attending the PTC Live Global 2015 event is not a pre-requisite to participate in this contest.This contest is covered within the PTC Community Terms of Use Agreement - Section #5 "Content – Submissions."Wat
Add the capability to shrink the elements with a fringe plot to view the stress contours within the model, as shown below.
Von Mises and convergence (shown below):
Alvin,If you want the mesh to look like your desired post, you will have to rotate your hole 90-degrees. I've posted the solution below, as I think this is the type of mesh you're looking for.
The *.avg file is not a user-readable file, which lists the h-nodes and the corresponding p-elements where stress averaging should not occur due to shell tangent discontinuity.
Can you change this post to a discussion instead of a question?
I found them all but .avg, and I'm still searching that one in some of my older references.
Barry,This looks like a thermal analysis on a component without a force load, and the component is constrained in such a way that you're receiving the warning. This analysis is a Quick Check (p3 to p3), and there are no measures in your summary file.Can you upload an image of the part, or is it classified?
Can you post an image of the pattern?
Alvin,I'm only posting these results to make a point. I made a simple plate with a hole, ran a mpa analysis with about 1000 shell elements, and it only took five seconds to run and obtain convergence within 1% (spa about two seconds). I've seen a lot of models where people try to break up the elements around a hole to make it look like a hand mesh, but with the p-element, you don't really have to do this. I created a lot of elements on purpose, and I certainly don't need this many to meet convergence. Try auto-meshing your model without Edge Distribution and check your results. Hope this helps.
Frank,They are defined in the Help Center, as I stated before.http://help.ptc.com/creo_hc/creo30_sim_hc/usascii/index.html#page/sim/simulate/online/filelist.htmlFor example:.a01 is listed as study.a## (then read the right-hand column).d01 is listed as study.d##
Barry,Did you receive a fatal error, and that's why the run doesn't complete or are you just getting warnings? Upload the .rpt file (run summary file).
I assume that there is currently no provision to post a Product Idea in the specified topic.
I've created a 2D drawing from a 3D model on a C size sheet. Is it possible to change the drawing to an A size sheet and keep all the work I did on the C size sheet?
Hi Agnes,Good. I hope this has been of some help, and you can create the geometry, symmetry constraints, and mapped meshing to meet your criteria.
The product called Solidworks, as folks know it today, has already split into two development streams. Solidworks will stay as it is with the same modeling kernel until and beyond the time when development is halted in the future. For CAD, a modeling kernel is analogous to the engine, drive train, and chassis of a car. Solidworks V6 (now called Solidworks Mechanical/Conceptual and other solutions will be added) will be the new product that will take over Dassault's development efforts and it will be based on Catia's modeling kernel. If they wish to avoid any data disruption, Solidworks users of today will need to continue using today's Solidworks in the future even though there will come a time when there will be little to no further development effort put into the product. Dassault will give incentives to entice existing Solidworks customers to move to Solidworks "V6" (Mechanical/Conceptual) even though there will not be true data compatibilities. Solidworks "V6" will likely have the
Demac,Please look at Page 7 in the attached file. Currently, PTC does not have CFD, and I think there is a Product Idea to add this capability. But there is a product call FloEFD that can be used with Creo.
Are you going to make this a Product Idea?
Jim,I've been using Creo Simulate since it's introduction with 1.0, and prior to that, all the way back to Mechanica and Pro|Mechanica (1999).
Anges,I've attached the model, and I found out that the more brick elements I added, the smaller the % difference between the max and min radial (R) displacement. You don't have to use as many elements that I used in the attached model, and you could use just a 1/4 model, as I was just experimenting (Creo 3.0).
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.