Recently active
Hi, We are using Design Exploration. We are finding that there are some scenarios when checkpoints are created inadvertently, which causes the number to go higher. We then have to delete checkpoints and end up having checkpoints with numbers like 5, 13, 22. The issue is that we are building a top-down approach for engineers to select a design concept and push that out to Creo and then configure it using a skeleton with parameters. We would like the numbers to be able to be: Hidden Customizable Able to be rebuilt where the first checkpoint starts with 1 again. Thanks!
It should be possible to open a Design Exploration File from the Windchill Workspace with the open in Creo button in actions the way every other file can be opened. In addition if you are in the information page of the TMU file you should be able to click on Actions and open in Creo as well. Currently only able to open in Windchill from the normal file dropdown within the workspace.
It would be nice to create configuration option to specify the model which will be used as the default skeleton template - for example: template_skeleton
Sometimes, software requires neutral files, e.g. Parasolid or IGES, to be supplied in a specific version. PTC's position is to export in lower versions of neutral files as it maximises compatability, but the version of Parasolid particulalrly is too old to be supported by some software that is supplied to us for use with a particular piece of hardware. We require a version equal or newer than version 14. Creo Parametric can import Parasolid files up to version 38. Please also allow the ability to export in newer versions.
Currently it is possible to display the assigned material and its values for example density, mass inside the model tree but it is only possible to display the values without the unit of measurement. Right now (Creo 7.0.2.0) there is no way to add an extra column with the unit of measurement next to the value but this would of course be a valuable functionality. To display a value is useless without its unit of measurement. In this example (without units) it is not really clear how the density of the main assembly was calculated. The values of some parts are pretty much too small to have that result for the main assembly. Easy to understand if the units of measurement are beside the column (but currently not available). After changing the unit inside the parts from mm to cm the whole calculation is more understandable. The display of the values in general makes more sense if the unit of measurement could be available next to the collumn.
Reference Case: 15655921 Reference SPR: 11246232 Although we design in English units for most parts, we are using metric sheetmetal thicknesses. We have therefore changed the unit for the SMT_THICKNESS parameter and set it to be calculate. When we update the thickness dimension, it does not flow back up to the SMT_THICKNESS parameter and convert to the metric value. This parameter would be used in model-based-definition annotations (like 1mm thickness, 1.2mm thickness, etc). We want it driven from the english dimension so there are no inconsistencies. Thank you!
Reference case: 15640004 Reference SPR: 11255994 Some parameters, like smt_dflt_bend_radius do NOT update when you change the unit of the model. This is potentially a big issue. Either: The model fails and the user takes precious time to investigate and fix the issue - Not ideal The model doesn't fail and the user visually noticed the geometric differences and investigates and fixes the issue - Risky The model doesn't fail and the user didn't realize that the internal bend radius is much larger than before - Spoiler alert - It happened!. This is an issue as it impacts the model and the design. Please fix! Thanks!
In the feature who support the "sketch region" filter, there should an option of select and deselect the specific selected and non selected region. Which help in to increase productivity.(view in My Videos)
CREO offers two schemes for altering model units: conversion and interpretation. Of these, the conversion option adjusts geometry and model material properties to stay self-consistent, while the interpretation option changes units for both without adjusting either. This means that the interpretation option will alter the material properties, which requires the user to set them up again. This is especially problematic for organizations that set up models with a default material already assigned. Sometimes users may forget to change the units until they have already started modeling geometry, which requires them to use the unit interpretation option. Current workarounds consist of either using a manual scaling operation or resetting the material properties after unit interpretation. It should also be noted that this process tends to confuse new users, who generally don't expect this behavior. It would be nice if CREO included a scheme that gave the option to conduct a unit
We faced an issue with several Windchill cloud environment connections from Creo to Windchill. Creo Server Management allows (/ is intended to be used) to register several Windchill servers for one instance. We have Test, Development, QA, and Production environments, which all are running on PTC Cloud. If user tries to register all of these environments, they receive an error stating that "Server is already registered" (with two of the environments): This occurs because Creo identifies those to be the same environments (based on the IP?), even the addresses and names are different (e.g. QA https://eg1-qa.ptcmscloud.com/Windchill/ vs Production https://eg1.ptcmscloud.com/Windchill/). As these are on cloud, the public IP addresses get changed over the period of time and thus it is not efficient to register those as "local" variables on Windows. To by-pass this, we need to create environment specific starting .bat's, which are then using different Cache folders (e.g
Ticket Reference: 15668428 SPR Reference: 11556077 We have an Extrude that references the edge of a quilt by using the PROJECT command in sketcher. When we flip the direction of the quilt and then flip the extrude the feature fails. If we do an edit definition of the sketch in the Extrude and then click OK, it works again! PTC R&D says this is a 'limitation of the software'. 😭 The official word is: “The limitation is that the edges formed a counter-clockwise loop at the time of creation. So now when they go clockwise the software considers this inside-out contour and changes the material side of the extrude. The software does not recompute the orientation to preserve the user intent.” Please fix. Thank you!
It's a long time since we have something new into mechanism and now it is becoming obsolete (from my standpoint, obviously). One great area of improvement in my opinion is the one related to the interaction between bodies (cam or 3d contact). The way this type of interactions are managed is fiddly and heavy. It is frustrating for an old former PTC consultant like me watching other CAD doing now what is not possible in CREO while in the past the situation was converse ( see this example: https://www.youtube.com/watch?v=Phlij0roGs0 ).
Simplified representations (Simp. Reps.) set by rule condition (just for an example: PTC_WM_LOCATION=="/Libraries/") are not automatically reEvaluated when the contents of an assembly changes. When defining these kind of Simp. Reps. on an existing assembly - it works OK!But, when adding or removing Windchill Library components ,these Simp. reps are not changed, accordingly! This behavior leads to errors when exporting to a Creo View PVZ file, as the output file show incorrect content when switching to see the Simp. Rep. My Suggestion for PTC Adding a new config option:Enabling this option would pop up a message for the user each time he saves an assembly with Rules Conditioned Simp. Rep. to a PVZ Creo View file.The user is prompted for a specific Simp. Rep. that might be compromised, because it is driven by Rule Conditions.The user is asked if he wants that Simp. Rep to be auto ReEvaluated, and only then the file saved to the PVZ File.
Today some 3D notes can be used with drawing simplified representations for cable assembly drawings centric fabrication. Would like to suggest harness manufacturing us simplified representations with 3D annotate flat to screen combined views. This would be used on our 3D harness manufacturing flat pattern model process "nail board". Windchill MPMLink author states use combined views for EBOM/MBOM assembly wtPart structure. "Using simplified representations with combined views on harness cable assembly 3D Annotate functionality" This would allow us to use MBD assembly features designated control characteristic with our 3D flat patterns to support our harness MPMLink fabrication process planning 3D work instruction operation sequences. This uses Creo View / Illustrate Would like to use annotation tab "flat to screen"; 3D annotations Reference Designation "Feature Name" and/or Ref_DES Dimensio
Creo Live Simulation allows the user to set the top and bottom of the scale. I suggest that the user should be able to use any color division or at least orange to red to set the scale. The reason for setting the scale is to visualise where the stress goes beyond a defined limit. Setting the top of the red scale does not provide a delineation at the defined limit. To get this the user must calculate the scale settings required to get the required value at a delineation on the scale. Example: To set delineation between orange and red: ((Required value - bottom of scale) / 8 * 9) + (bottom of scale)= top of scale Make setting of scale to needed values simpler. The computer is much faster and better at making these simple but time consuming calculations.
In Creo Drawings, please add the ability to duplicate a sheet or views AND also copy the view dimensions, annotations, balloons, etc. Here's everything I've tried: The 'Move or Copy Sheet' command creates a new sheet EXCEPT it removes all dimensions from all views. Please keep the dimensions. You can backup/rename the current drawing somewhere and then try to 'Import Drawing/Data'. Sometimes the dimensions are kept on the new sheet(s). Sometimes not. Please keep the dimensions. Creo doesn't seem to support copying views You can try to select view(s) and copy/paste - nothing happens You can select views and try 'Move to Sheet' but there's no option to copy to sheet. Please add this option. A use case would be using 'Replace View Model' on the copied views to then swap by by Family Table, Simp Rep, etc. without having to redo all the dimensions.
I know a similar request has already been submitted but archived, but now that we have the multibody capabilities in Creo, I think it's worth considering the following: When trimming a quilt, we only have options to trim by other quilts, planes, edges, etc. There is no option to trim by another body, but it should be very useful, and avoids having to manually select and duplicate surfaces just to be able to intersect a quilt by a body. It would be something similar to an extended boolean operation features already proposed for the multibodies, which would allow us to select wich part of the intersected quilt (or body) we would like to keep or reject. Please, see the attached images:
The regeneration footer concept is very interesting and useful, to have some kind of analysis features to be made only after the model is totally regenerated, like measuring the weight for instance. Even though the concept is usefull, it could still be improved, by allowing further feature types to be moved there. Currently, only this types of features could be moved to the regeneration footer: "To Move Features to the Regeneration Footer You can move the features that are created by default in the active list (in the Model Tree above the Insert Here node) to the Regeneration Footer. These features include the Analysis features, Publish Geometry features, Reference feature, Annotation features." Only simple features is not enough. I created a group to measure a solid body to always have an up-to-date bounding box dimension for a part. The problem is that the group cannot be moved to the regeneration box, even if uses mosly analysis fe
Currently all the relations and parameters values that we specify get edited out by Creo, converting EVERYTHING to uppercase after we try to use Pro/Program to implement "conditional features". (Suppressed based on parameter values). Since we have lots of parameters that are String Values, mostly Restriced parameter values, that use a mixture of lower and uppercase letters, all the automation conditions get invalidated, whenever Pro/Program converts everything to uppercase. It should not alter the relation strings, or if it does, it should only convert keywords, like "if" to "IF", but should not touch any strings inside quotes. If we have a string restricted parameter called "FixedSide" and use a relation: If ParamA == "FixedSide" .. Endif and later Pro/program converts the relation string value to "FIXEDSIDE" like this IF PARAMA == "FIXEDSIDE" .. ENDIF Then we have a problem, since the Restriced Sring Parameter was not converted,
Having external file drawings as separate entities inside Creo philosophy is very useful, specially when dealing with large and complex parts and assemblies, where there is a need to eventually share work among several team members, besides allowing operning only the 2D drawing files, when someone will not look into the 3d geometry. Having said that, there are CAD packages, namely VX, if my memory seves me well, that did allow each part or assembly to have embedded 2D drawings. For small parts and assemblies, or with simple 2D drawings, where the drawings are made by the same user, and there is no need to share work, there are also advantages to have the option of creating an inside part or assembly embedded drawing. In our case, when trying to implement automation, designing "skeleton" start parts for later deriving 3D geometry to finalize the parts, using a multibody approach, where each body will define the size and positioning of later derived parts, it would be extre
Hi, In the graphic area the demotions overlap and it’s difficult to find and select the desired dimensions. In addition, the table doesn't help to select because it does not show the dimensions values. The column of dimension type is irrelevant. they appear in red color and the user must REPAINT to see them in yellow color as other exciting dimensions. Requests: Automatically arranging the display of dimensions (Clean Dimensions) Add column for dimensions values in table. Add dynamically filter search for table.
Have you ever replaced a round with a chamfer, or redefine a radius significantly so that it causes a failure downstream of the change? I do it every day. Most commonly, I change a model feature and it creates failed "surface sets" in the Pro/NC manufacturing features. In the attached image you see the result of changing a round to a radius. There are several failed surfaces (Round 7) because it is no longer in the model. For me to fix the Mill Surface or Mill Volume that these failed surface sets are a part of, I as a user have to select, right click and delete each of the missing items. Wouldn't it be great if I could "ctrl - select" a whole bunch of them? There could be hundreds of these to delete in order to preserve the Feature without starting over. Left Click select, Right Click, Delete. Left Click select, Right Click, Delete.... This is one of the most inefficient processes I find with Creo Parametric. You can g
Since Creo7 it works in a drawing. See Creo7 manual and video: Manual: Place Multiple Normal Leader or Tangent Leader Annotations in Drawings Use Add Leader for multiple normal or tangent leaders from a single annotation. User Interface Location: Place a leader annotation normal or tangent in relation to your reference, right-click and select Add Leader. The Add Leader command is applicable to GTOLs (geometric tolerances) and notes. To add a normal or tangent leader for the non-modernized annotations (symbols and balloon notes), click Attachment and then click Add ref. Release: Creo Parametric 7.0.0.0 Video: https://youtu.be/i8-O6VVrJDo It would be great if we could have this functionality in the model.
Be able to customize Creo Parametric Navigator area and priories what you need to work with the most often. Our users, work with Windchill in different Workspaces. Be able to display by default the Workspaces Folder would be great !
Flexible Modeling Body move operations should have the option to also automatically include "attached" datum axis or datum thread quilts. If that association "axis <---> hole surfaces" and "thread quilt <---> hole surfaces" already exists in Creo database, this should be straightforward to implement. If not, Creo database should be improved to internally keep that association when using the hole or thread hole command. Also, these axis and thread quilts should also be optionally automatically all included when using data sharing features, such as "Merge / Inheritance" or "Copy Geometry". When copying Geometry, if we select a body to copy, we should have the option to include all the body axis and threads, with the option to eventually exclude some unwanted ones. Also, when doing boolean operation, such as body boolean cut or boolean intersect, in the resulting body geometry should only be included the datum axis and threads belonging to holes surfaces that do not "di
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.