Recently active
Actually the edges preparation is not allowed for this kind of welding. Furthermore, even if the preparation is made with a part feature (e.g.: a simple chamfer), you're not able to "fill the empty/cavity" with the welding's material. The Eurocode 3 allows the edges preparation for fillet welds.
I want to get back this thread because it has been archived by PTC because of too few votes in a long time.But I think it should be useful: insert the possibiliti to define the lenght for the edge preparation.In addiction I also propose to implement a better interface for edge-preparation (see image below) and a command that permits to recognize ordinary chamfer features as preparations.
At the moment it is not possible to create a hole table with holes from a part in a assembly drawing. After selecting the coordinate system, PTC CREO 4 will say "No items founds". It also is not possible to select a coordinate system which is in a part from a assembly. My feedback is to add the functionality to create a hole table in a assembly from holes which are located in a part.
I want to be able to save the result of thickness check. Currently, the result of the thickness check cannot be confirmed later.
The new API for Creo (Object Toolkit) does not have the same functionality as previous API (Toolkit) to copy a UI Component and place it in Table Cell (function ProUITableCellComponentCopy()). The new API had big improvements during Creo 4 and 5. The development is now stalled... The documentation is also poor and are less code examples (than Toolkit).
it should be solved the problem reported in Article - CS125746. https://www.ptc.com/en/support/article?n=CS125746&language=en&posno=1&q=measure%20poor%20performance&source=search It's really annoying the performance of measure command with large assemblies.
The creation of drawing dimensions would be faster if you made possible to align dimensions to snap lines directly when creating drawing dimensions.
When using the “Global interference” analysis in assembly, it would be very useful to have an automatic zoom that centers the screen on the highlighted interference. You could insert the “Zoom to Selected” button in a mini toolbar when a row is selected in the Global Interference window. Currently (Creo Parametric 6) no mini toolbar is shown when clicking on a row.
Bend Line Adjustment (BLA) should indicate default versus customized versus calculated values. (To mark the areas in color, which must be determined empirically) Reason: In Undeveloped (bent) state, the DEV.L is NOT visible as calculated, customized or default until user edits the value In twist feature, the DEVELOPED LENGTH (DEV.L) is calculated as 2*attached_edge_length. This is an unexpected calculation. Expected is a default DEV.L = length_of_bent_edge OR an obligatory manual value Example: Twist feature attached on a 30mm edge gets a default DEV.L value 60mm although user sets a wall length value of 15 Twist feature attached on a 30mm edge gets a default DEV.L value 60mm although user sets a wall length value of 100 Twist feature attached on a 60mm edge gets a default DEV.L value 120mm although user sets a wall length value of 60 Bend Edge feature gets a DEV.L value of 12.3 (calculated) Bend Edge feature gets a DEV.L value of 22.2 (manual), which is not looking a
Have the ability to toggle a layer property that would enable that layer to print/publish when creating a PDF. For example; Datums, I don't want my users to create PDF's with the datums still showing for obvious reasons... Would like to keep datums on "no print layers".
For resuming and suppressing of components in creo toolkit we have ProFeatureWithoptionsResumen() and ProFeatureWithoptionsSuppress() but if I use this API's for suppressing or resuming ecad components then those components are being added to flexible/Varied Items. So, I think we need to have different suppress/resume api for ecad non flexible boards, so that using this the components should not be added into Flexible/Varied models.
For hatching breaks, the dimensions with marking for a basic or inspection dimension are currently not correctly supported. The break does not include the frame around the dimensions. The hatching is only hidden in the range of the dimension number and the tolerance. The identification of the frames is made considerably more difficult. For basic dimensions this can be improved by increasing the size of the margin. In the case of inspection dimensions, however, this change leads to unsightly representations. The figure shows the behavior for the different dimensions. The dimensions to the left of the respective hole have the normal margin width. On the right an enlarged margin is used. Friends of fine, easily readable drawings certainly agree with this suggestion.
It would be awesome to have the "locations" feature in Piping. Locations are currently used to route on Cabling and they make cabling routing extremely easy. but when you are routing a flexible hose on Piping it would be extremely useful to have the feature of adding a "location" or even better an "offset location" without having to care about the order of the pipe segment in the model tree. You need a location, you add the location, done. You need to make changes, you edit definition of the location and place it on the correct position and done.
It would be awesome to have the "Tape" feature on Piping as it is on Cabling to indicate the location and color of tapes. Tape marks are commonly used in hoses for identification, alignment, mistake proofing or to indicate the position of a clamp or retention. Right now the Cabling module in Creo allows the user to add Tapes in the harness and that Tape location/distance from other components can actually be measured on the drawing and it is even exported in the XML if you use other cabling specific software for print production.
Hoses are generally used to convey fluids when a tube cannot be used because there is motion or vibration between the connection points. It would be awesome if Creo would have a tool to simulate the behavior/motion of a hose on a pivot or slider joint mechanism and analyze/optimize the hose length and slack to be able to meet all the positions in the mechanism and show the stress concentrations and bend violations or failures. This tool could also be used for cabling simulation.
Add functionalities to Graphics Toolbar. For example: adding Datum Tags.
The assembly command Bill of Materials allows to exclude (filter out) unplaced components. It is not possible to achieve the same with repeat regions. The model tree column Feature Attributes holds the values I would like to filter for, but repeat region filters don't know about this information. Please make repeat region filters aware of this source of information.
Please add an Auto Chamfer feature similar to the Auto Round feature for symmetrical chamfers.
I would like to know in the changes control window, which parts volumen are changing (there is the same about the position).Nowadays as we work with parts sustractions if we consult the parts changed CREO informs that all the parts substracted to the main has changed instead of not really been changed.
Currently the Back Up References command does not back up the references of surface copy features (). It also does not back up the references of simulation features. I expect the command Back Up All References to not just selectively back up some references but to back up all references.
Current Creo could not dimension the arc full length. Hope to improve the dimension system to get the widely used arc full length dimension rule. See below
CREO should have the ability to create a rough offset from surface. This is very useful, for cast design, and also tooling designSee the example, from other CAD applicationhttps://youtu.be/Bfv0kEa8W_w
組み合わせステートに追加されたアノテーションを組み合わせステートを開かずにどのステートに属しているかを確認する機能を追加してほしい
In AAX, it should be possible to publish a sketch, and in the part that have received this copy, it should be allowed to extrud it (or create any other feature), without the need to project it to a new sketch.
Issue:There is sometimes need to produce Fringe plots with user defined content in the Creo Simulate post-prosessing.Today:Computed measure functionality on can be used to calculate user defined measure results. Unfortunately today it can be done only per point rather than fringe plots. One can combine this with Behavioural modelling (Field points, User Defined Analysis) for the required results, but computation time is HUGE.Sample cases:Hill-48 yield function (non isotropic VonMieses)ASME BPVC.VIII.2-2015 section 5.3.2 (combination of primary stresses)
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.