Recently active
we are using Creo Design Engineering Package. We are facing an issue, while saving file with some changes or even creating a new file, software program is not creating "Numerical Control" (NC) for machine. We are first time user and not familiar to this software. Kindly support us in this regard asap. Regards
Hi All, Recently I replaced my graphics card for a Nvidia RTX 4000 card. Since then Creo (8.0) tends to crash way more often. At first I had my doubts whether Creo is using the card or grabs back to the onboard card but in Creo the system information tells me it is using the RTX card. Any idea how I can figure out what causes this crashes? Is it coming from Creo or could it be the card itself? Thanks in advance!Bart
Hello all, I want to know how to define ProAsmComppath used in ProSelectionAlloc for a feature in skeleton used in assembly. I have feature ID for skeleton as 98 and in this skeleton I have a feature whose path I want to add has feature ID 3560. I saw in knowledge hub mentioned the method as {98,3560}. But when I try in ProSelectionAlloc to mention this way. It shows error How do I mention correct path in ProSelectionAlloc (). Thank You.
Hi I have recently installed Creo 11 and been able to make tables in MBD. I would like to be able to see these tables and other annotations in Creo View Express I export the Creo model with the tables and other annotations to pvz format and expect to see the tables but they aren't there. I can see dimensions with GD&T callouts so I am assuming my recipe file (attached) is ok. I did some digging and found that maybe I need the Creo View adaptor 11.1.0.0? Do I even need the Creo View adaptor if I am manually creating the PVZ file using Save As from Creo 11? Support_for_Table_Annotations_for_Creo_Parametric I thought maybe my version of Creo View Express was the issue so I went to the Creo View Express download page here and even though it says Creo 11.1. it downloads 11.0.0. I installed that and loaded my pvz file and still no tables being displayed. I used a recipe file as attached. I had to change the rcp exte
Executing a modal analysis for an assembly with several parts, an internal engine error occur and stop without any other notice.In .err file:------------------------------------------------------------Creo Simulate Structure Version Q-10-51:spgError ReportTue Jan 14, 2025 15:48:52------------------------------------------------------------An internal error has occurred in file elmpkdr.F, line 234.*** A fatal error has occurred. ***An internal engine error has occurred. Please be sureto run error checking before you run this study. Ifyou have run error checking, then contact Customer Support. The analysis has "bonded contacts" as default. All contacts in the model are "free". No interference between parts. All materials properly defined and linear. Due to the complexity, model has 1.4 Million elements. There is no RAM memory deficit, actually computer has 80 GB. I have checked this topic during analysis and only reach 50 GB. What could be the root cause for this erro
I am trying to do a cable parameters export and then import the file back. Even though I try to import the exact same file back, the ProInputFileRead-call crashes Creo without error code. The whole of Creo just dies with a fatal error popup. I have tried to import the same file manually in the Cable Parameters window using and that works fine. ProError fileExportStatus = ProOutputFileMdlnameWrite(mdl, L"cable.cbl", PRO_CABLE_PARAMS_FILE, globalHarness, (ProAppData)wideString_c, NULL, NULL); ProError fileImportStatus = ProInputFileRead(mdl, L"cable.cbl", PRO_CABLE_PARAMS_FILE, globalHarness, (ProAppData)wideString_c, NULL, NULL);
I am using Creo Parametric Release 7.0 and Date Code 7.0.8.0I need to export a 2d drawing to .dxf. The export works so far, but unfortunately a view outside the drawing frame is exported as well even I choose "all sheets as paper area" (translated from german). Is there a way to export just the sheet w/o outer elements? Thanks BR.
I am using Creo Parametric Release 9.0 and Datecode9.0.7.0When tangent edge line style is being changed to any other than default, using reset button or copying style from another tangent edge will not bring default style (thin continuous line), but it will set it to the line style of contours (wide continuous line) instead. The issue affects how drawing exported to PDF format looks like (line thicknesses).
Do you have any specific notes on the library components, saying that "This part is for graphical representation only. Detailed information should be available from the supplier"?
Hi all, Greetings!I need to automate export part/asm to STEP format with different options OR through different profile files in Creo. I checked Mapkey does not work. Anybody suggests how to do it? OR any API or batch files that can solve/work.
I can change the View in the Searchbox (File -> Open) of Parametric. So its possible to show also attributes instead of just the name. If i close Parametric and open the Searchbox again, Parametric will run with the default UI of the Searchbox and will show me just the Name again. How can i save this Setting. I tried it by saving the Customization_ui but it didnt work. Is it possible? If yes how can i save the setting?
When deleting a patterned part you get (2) options "Delete Pattern" and "Delete". If you are getting rid of the part completely, I have typically just chose "Delete". When this is done, the family table has a orphaned dimension left in the table for the quantity of the pattern. Why would the pattern quantity not be deleted also?
How do you resize the column widths in family table beside dragging the divider line in the header?
I am using Creo Parametric Release 11.0 and Datecode11.0.2.0when ı choose profile(framework) which Bosch type like sigma, it seems only rectangular.
I ran into a large assembly that I cannot save after changing some parameters.The parameter does not seem to have anything to do with regenerating the assembly (it is date and designer name).From the warning messages that appear after I tried to save the model, I have found 2 support articles, but I could not read them. Could someone please tell me what is in these two articles? Thank you so much!https://www.ptc.com/en/support/article/CS258240https://www.ptc.com/en/support/article/CS112336
Hello,is it possible to manage default font type/size/linestyle for cross sections?I want to follow technical drawing stadards in my country but Creo always use default font/color/linestyle for section name which is not correlating with cross section default arrow style (because it is just a note). I am missing something like these "drawing.dtl" options: crossec_font_color (valid for arrows and xsec note)crossec_font_height (valid for arrows and xsec note)
Has anyone come up with a way to export the centerline of cooling lines or solids of cooling lines from a mold design? We are being requested this from customers and simulation contractors.
Hello,It is impossible for me to open my files generated in pvz by Creo on my Ipad through the CreoView app. Here is my export configuration file : I load my file on icloud, chose send to Creo View, the app opens and... nothing happened. Any solution or advices ? Thanks in advance.
Hello,in a toolkit application I need to know if an edge is an inner or an outer edge.In the attachment I have an example what I mean with inner and outer edge.What I have up to now:I use visit functions to get all the edges in the part model. A function to determine if the edge is "inner" or "outer" seems not to exist (I found none). But there is the function ProEdgeNeighborsGet(), which has the two surfaces for every edge as an output parameter. Is ist possible to get the inner/outer information with this two surfaces? Or is there another procedure to get the information.Any help would be appreciated.regards HP
Good morning, I'm having a similar issue, the thread note that you are seeing is a note of a cosmetic thread, In the holes made with standard hole i can apply the note that i would from the .hol file but in the hole made with cosmetic thread i'm not able to understand from where it's taken and i can't edit. Even if in the cosmetic hole thread i'm selecting the same library of the standard hole with the "right " note i'm not able to obtain the result this i want. any suggestion? Thanks! Reference topic: https://community.ptc.com/t5/3D-Part-Assembly-Design/Cosmetic-Thread-Class-Issue-Creo-5-0/m-p/612900#M65730
As part of our migration to Creo 8 / Windchill 12, we came up w/ smart formats fed by parameters in our new start parts. When we have a new part on a new format life is ezpz. However, if we have an existing part w/o the required parameters things get complicated. I came up w/ a mapkey to add the needed parameters to the existing part that works well when we want to put this part on a new format. Problem lies in a relation we have in our new start parts. It's the one below that sets the value of the MATERIAL parameter equal to the value of PTC_MATERIAL_DESCRIPTION. Each material has a defined description in it. /*This relation sets the material parameter equal to the material description thru a yes/no parameter IF (USE_MATL_DEF_DESC)==YES MATERIAL=material_param("PTC_MATERIAL_DESCRIPTION") ENDIF /*This information needs to be pasted int
Has anyone taken the Creo Certification courses, and if so, was it worth it? Do you maintain your certification once you've earned it? I primarily work with "complete machining" extension. I've been using Creo since 2012, currently on Creo 10. I did a lot more modeling back when I started, but now we receive models from the engineering group and I use them to program the manufacturing. I did go about reaching out to Sales about the associated costs. My fear is that the courses are sort of entry level and will be a waste of my time. It appears that it may be an opportunity to see some of the work with the High Speed Milling extensions without having to purchase those licenses. Anyhow, I'd appreciate any input on how other's experiences have been with these certification courses. Thank you,Matt
I am using Creo Parametric Release 11.0 and Datecode11.0.0.0Unable to add transitions or multiple radius values when using the D1 x D2 conic option.
When exporting a cad model as a PDF U3D I select to export annotations and parameters in the content tab however when i open Adobe Acrobat reader, I cannot find the parameters. There is a side section that has property and value columns but no which part I select those columns do not populate. Where are the parameters?
Hi,This message can also be found in the product ideas. Inseparables are used to show/save an assembly as part.Currently, while scanning the BOM an inseparable is handled as an assembly instead of a part.This leads to errors in the BOM list.- main assembly - part 1 - part 2 - inseparable 1 - part 3 - part 4 - sub assembly 1 - part 5 - inseparable 2 - part 6 - part 7 Setting "Scan Inseparable" = "OFF" (Anything located below an inseparable is used as BOM entry)=> OFF = The inseparable will be calculated=> ON = The inseparable will be ignored, parts will be calculated separate Current outcome SCAN ALL LEVELS:- part 1- part 2- part 5Expected outcome SCAN
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.