Recently active
Hi, I need to do a simulation with Creo Simulate 10.0.3 as indicated in the subject.I used shell finite elements ans it is not a problem to set constraints and the internal idrostatic pressure, the problem is another The tank is covered by sand, 30 cm per side as indicated in the attached files. The sand causes a force on the tank, and limits the lateral expansion. How can I interpret the sand? With a Force/Pressure on the tank and a laterally Pressure/Constraint/Springs to limit the lateral expansion? In order to represent the sand I also thought to create an external component/body but I think it is too complicated. I'll need sand structural property and I'll have to decide if use bounded interface or contact interface between tank and sand.Any suggestion? Thanks
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo 7.0 2. What is the problem?It is difficult to remove a component or subassembly from an explode state. Occasionally parts of a subassembly are moved instead of the subassembly, and it is not noticed until later. To remove the explode position from a part, you must find the part in the list in the View Manager Explode Properties (which may be 100+ parts) select it and select Remove. I would like to see a function in the Edit Position Explode tool to remove the explode state of a selected component. 3. Are you using a workaround? If yes, please describe it.- Exit the Edit Position Explode Toll and scroll through the list to find the part, then select Remove. - Copy position to a part that has not been moved. (still has an explode position) - In the Explode tool, select part, RMB, select Toggle Explode (still has an explode position) - In View Manager - Explo
I am using Creo Parametric Release 8.0 and Datecode8.0.5.0When using IFX I am unable to create an instance for PEM fasteners. I set the folder to create the part files and then select any of the OOTB dat files provided for PEM fasteners and CREO returns a PRO TK error. I have had no problems when creating any other type of nut, washer or screw, it is only PEM fasteners that do not work.I have noticed that there are no nut_80.prt or nut_99.prt files in my folder C:\PTC\Creo 8.0.5.0\Common Files\ifx\parts\ifx_fastener_templates\nuts (if that is relevant)Here are the errors that I facedError message reads "An unknown error occurred (PRO_TK_E_NOT_FOUND)
Hello, Is it possible to put chain dimensions in a set so that they are linked with each other? It's handy when you move one of the dimensions that the other ones also follow. Kind RegardsSEEBO
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?I'm using Creo Version 72. What is the problem?Lack of cable routing options in cabling application. I can't wrap wires around a cylinder.3. Are you using a workaround? If yes, please describe it.Select "on surface" and click multiple times around and around and around. It looks very messy and adds a lot of wire locations.4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.We thermally anchor our wires and cables around support legs and struts by wrapping cables them around and around a object to ensure good thermal contact and dump the heat. Currently you can choose to place or offset from a surface or place on an axis. I would like the option to offset from an axis to be able to rotate the wire in a uniform way around the axis. An alternative option is allow it to go on an existing
Initially posted in this topic Sorry for digging up a really old discussion, but this issue is still relevant.Windchill Help still claims that opening a .pha file downloaded from Windchill with standalone browser should open the model in an existing session if one is open, but it's not working like that for me: I tried with associating the .pha to parametric.exe and to parametric.bat, but both just start a new Creo session. My Creo version is 7.0.10.0.Has anyone ever got this working properly?
Hello everyone, I am experiencing performance issues with working in annotation. The best example of my problems is when i copy a piece of text.When i try to move the copied text it follows my cursor with a 5 seconds delay.I also have those kind of problems with placing and moving views and dimensions.Our local ptc support told me that it is graphics card related. I am using Creo Elements Direct Modeling 20.4.1 on a HP Envy laptop with a Nvidia RTX3060 graphics card and windows 11. I have installed the latest driver for the graphics card. When i loop up in the HP compatibility matrix, my laptop and graphics card are not listed.Could it be that te laptop is not compatible enough to run Creo elements direct modeling annotation correctly? Or could it be a graphics setting that is not correct? Thanks in advance.
How can I show the thread (of a threaded hole) when the axes are hidden?
Thank you!
I am trying to model a fish scale array pattern as a film like structure. but unfortunately i cant able to create the overlapping surfaces. I figured that I need some degree of tilt between the individual scales and the base.Attached pictures of what iam getting and what I need. Help me to get the desired output.
Using Creo Parametric 8.0.4.0 - Spin Center is turned off so that it will spin about the mouse location. Datum Plane shading is turned off (though it doesn't matter if it is off or on), and are not visible in my model. When I hold the middle mouse button down, many times it won't activate the spin, and if I'm in a feature, often will close me out of the feature instead of activating spin. When it does activate the spin, as I'm spinning, the spin location will jump to other geometry as the mouse cursor goes over it, instead of staying on the entity or location where I originally started the spin. This only has happened since upgrading to 8. I never had this issue with Creo 5. Not sure if this is a graphic card issue, or an issue with Creo. Running on a Lenovo P51 with an Nvidia Quadro M2200 card. Incidentally, when I have Spin Center turned on, I still can't get the spin functionality to initiate many times when I hold the middle mouse but
When in Creo after selecting "open", the "File Open" dialogue box appears. This presents me a "list" of Creo files in my workspace. Most of the columns displayed in this dialogue box mean nothing to me. Is there a way to create custom columns that read desirable parameters that would help me better find files during my "open" process? Thank you!
Good Morning, I had initially posted a reply to a thread looking just to measure the MOI, I figured it would be better to start a thread of my own. I'd like to use CREO to calculate the Area MOI of some non-uniform geometry. Prior to doing that I wanted to test the tool on a known Area MOI before applying it to the non-uniform geometry. What I did was took an I-beam, calculated the Area MOI and then pulled the same beam into CREO and tried to use the analysis tool to confirm that it shows me the Area Moment of Inertia in the Inertia Tensor. But the units for the Inertia tensor are for that of just plain MOI (lb/in^2) and not the Area Moment of Inertia (in^4) - how would I measure this using Creo for a cross section? Thanks,MW
I need to find this file inside creo , I've searched and all the PTC folder , but it doesn't find anything pmech_conn.TXT
Hello, I had this error pop up for all my views when i wanted to update all the views on my drawing. First time having this error pop-up and i don't really know what it could mean. Can someone explain what it is and (if possible) tell me how to fix it without having to redo my drawing. I have a screenshot of the error itself that i will attach to this post. I am working with creo elements/direct 20.6.1. I didn't find the location for posts about annotation so that's why i have put it here. If this isn't the right place then feel free to tell me where i need to post this. Kind Regards,SEEBO
Hi All,I am getting Fatal error encountered.Can anyone help me on this error. i want to disable this error message for parament . i don't want to show this message even error occurs. Sharing snap and Trace file.
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo 9.0.7.0 and 10.0.2.02. What is the problem?Config option to stop Creo 9 layer/model/body/design items trees from snapping to various corners on the Main Graphics window.3. Are you using a workaround? If yes, please describe it.None other than having to drag/undock them4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation. A new config.pro option or window setting.5. What impact does this problem currently have on your organization? (Number of users affected, hours of lost productivity, etc.)N/A
Please include detailed documentation such as screenshots, images or video.1. What product and version are you running?Creo Parametric 8.0.52. What is the problem?Can not save as a component that is included in an inseparable assembly.For example, I would like to save as STEP one of the sub-assemblies in an inseparable assembly. 3. Are you using a workaround? If yes, please describe it.Yes I can extract the sub-assembly , change its name and save it as step , afterwards re embed it into the inseparable assembly.4. What is the use case for your organization? Describe how your idea would work in context or how it would apply to a practical situation.When we need to save as step one of the sub assemblies in an inseparable assembly.5. What impact does this problem currently have on your organization? (Number of users affected, hours of lost productivity, etc.)
Hello, I have an .NWF file that I have generated using a script, and it ignores all thickness/gauge/csa values that I put into it, and creo consistently lists all thicknesses for each wire as being 14.8221mm. for example, here's an excerpt of one of my new wires- NEW WIRE_SPOOL BLACKPARAMETER TYPE WIREPARAMETER COLOR BLACKPARAMETER WIRE_CSA 0.5PARAMETER THICKNESS 0.8PARAMETER WIRE_GAUGE 16etc. I have MANY wires, all with different gauges, and they all show up as spools with these dimensions: I can't edit them either, and no changes in the .nwf change anything in creo. I'd greatly appreciate help here. thanks!
I am using Pro/ENGINEER and Creo Elements/Pro Release Wildfire 5.0 and DatecodeM050Need to install a new license file
1. Describe your environment: What is your industry? What is your role in your organization? Describe your stakeholders.I am an engineer designing resistance welders.2. What version of Creo Parametric are you currently running?We are now running 8.0.1.03. Describe the problem you are trying to solve. Please include detailed documentation such as screenshots, images or video.When creating a simple hole, there are no notes associated with the hole that come up with the Show Model Annotations button in a drawing, unlike standard holes. Given that even a simple hole has a diameter parameter and a depth or thru option, I would guess that there is a parameter associated with those that could be put into a note that would be parametric to the hole feature.4. What is the use case for your organization?We create parts with holes and create detail drawings for them.5. What business value would your suggestion represent for your organization?Time-saving when creating drawings.
Looking for suggestions on how to model a sheet metal part that is a long and narrow L shaped bracket. A portion of one of the legs is formed into a shallow vee shape. The remaining portion of the leg is left out of the die and is flat. I’ve modeled the leg using a swept blend but can’t get it to unbend using deformations. Have attempted many other methods to model the part unsuccessfully. The transition area from vee to flat is noncritical. Thoughts?
Why am I not able to place end plates at the end of beams against a round wall? As you can see in the second photo it works on a flat wall. Thank you.
HiRecently I have been learning Creo Toolkit.I have some doubts about using ProToolkit and Creo Object Toolkit The development environment is VS2019 and Creo 9. As a beginner, I started learning the Protoolkit and later learned the Object Toolkit. I referred to the example code of PTC and found that there are exceptions when using interfaces that both exist. The Pro toolkit interface works properly, but the object toolkit interface may cause program crashes. Debug information output "Invalid parameter passed to C runtime function."For example, when selecting model items interactively, the ProSelect() function in the toolkit interface works properly, while the pfcSession:: Select() function crashes when the cancel button is clicked; When displaying messages, the Toolkit interface ProMessage Display() function can function properly, while the object Toolkit interface pfcSession:: UIDisplayMessage will crash. Similar situations occur in interface functions such as pfcSession:: U
Hi Team, I have attached a snapshot. I am using C# for my uses and vb API to communicate creo app. my requirement is to be control on pop-up message's "OK" or "Close" button, Is there any way to get control on this "OK" or "Close" button from my C# code? I mean want control to close that pop-up from my C# code using vb API. Any suggestion would be appreciated.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.