Recently active
Current issues (up to Creo 3.0)The reported mass properties (e.g. PRO_MP_MASS) can be changed only using the dialog > Model properties "change" > Setup Mass Properties > OK - see screenshots below. This opens a dialog that has two effects: (1) Define how the mass property is calculated and (2) Recalculate the mass and assign the value to PRO_MP_MASSIn the "Mass properties" dialog recalculated values are assigned on "OK" without respect on the fact if the "Calculate.." had been hit in the dialog or not.There are other ways to calculate the mass (e.g. Analysis > Mass Properties) which produce a message log entry "Mass Properties calculation completed." but do not change the mass properties (e.g. PRO_MP_MASS). This is misleading for some users:Current behavior: How to change reported mass properties (e.g. PRO_MP_MASS)Step 1Step 2IdeaSimplify this and clearly separate updating the reported mass properties (e.g. PRO_MP_MASS) from just viewing the mass properties.Possibilities to
Enable Restructure functionalities in Creo Direct, similar to the Restructure functionality in Creo Parametric
Please add ability to use model unit as system parameter, so that it can be used in relation and display in assembly model tree, BOM table and notes.
Allow to export PDF with stroke special characters option.Currently only "stroke all fonts" exists and that enlarges the PDF file size dramaticly.With this option we can have workaround for problems relating support for some languages.You have this as DXF export option already.
Please create an action-listener/ProNotify to determine when the Lock Status of a parameter has been changed. Another option, instead of creating an entirely new ProNotify listener, would be to change the PRO_PARAM_MODIFY_PRE listener to also activate when Lock status is changed, because then users can simply check for a change in lock status themselves.
I want to migrate to higher version customizations that I went against FluentU/I. Please create such a function.
I did a boolean operation with keep part turned off, then did a BUNCH of work, and decided I should have kept part. I used undo about 120 steps, saved the parts as a temp file and was horrified to find I'd lost all my redo steps, so could not get back to where I was.Save_package should not destroy all redo stepsCheck part properties without changing any properties should not destroy all redo stepsPlease add to the list of things that should not destroy all redo steps, but currently do.
PTC, please publish some kind of Validation data for Out Of Box functionality for Creo. We are not asking you to devolve any code or trade secrets here, just provide evidence that all the features work as expected.Creo tools have become a thorn in our side and a hindrance to upgrade. Here is our problem. We upgraded from Wildfire Pro-E to Creo 2.0 and were able to Validate the basic drawing functionality but the issue is the far more complicated feature of Tolerance Stack-Up and Mass Proprieties. These are OOB tools within Creo and we (as we do not have SW engineers) have no reasonable way of validating them. The result is that cannot use those features.For Tolerance Stack-up:We could do a simple calculation by hand (2, 4, 5 dimensional stack-ups - positive and negative) then compare to the result from Creo, then a more complicated calculation and from that conclude that any calculation Creo makes is correct.For Mass Properties:Perhaps compare the actual parts built?As you can se
Piping tab [Insert Fitting]-[Straight Brk]-[Create Pnt]-[Actual Len]This operation needs to input distance from an end point,but users can't know which end point is is reference point.They sometimes must modify it again.So, We need a function to show which end point of pipe segment is reference point.I think this function should be set originally.I mean, this is not improvement but SPR.
When I import DXF files containing the dimensions of "Radius, angular,and diameter dimension",Why are those dimensions divided to some parts ( text and geometry)?
Currently, when creating jogs in ordinate dimensions, the user has to carefully place each elbow, then zoom in and adjust the lines so they are not jagged.PTC, please add orthographic snapping functionality to jogs.
Several times, I have the use-case that I want to create a new assembly with existing parts in a new combination.So we have to create a copy of the assembly and then step into the replace dialoge separately.The ideal would be to run a "replace with unrelated part"-dialoge with automatic start of evaluation dialoge after pressing the save copy-button.- Example would be two nearly identical pistons, just with different material in two different engines.Now need to create a copy of engine one with piston of engine two.- Other example is to start some development improvements. After evaluation, create a copy of existing assembly with new part.
The toolkit function ProFeatureHasGeomChecks only gives you the information if a specific feature has geometry check items. I would to have also the information what type of geometry check failures the feature has (e.g. short edge, small surface, selfintersecting surfaces, ...). So an extension of the current function or the creation of a new function which gives you that information would be very helpful.
Currently in Creo Parametric 2, a user cannot change the ptc_common_name from a table cell, like can be done with any other parameter. The ptc_common_name is the Description equivalent in Windchill. It is so poorly integrated that it does not show up by default in the parameter list in the model tree configurator in Creo P2. Users have to type it in by hand in order to even see it.To change the ptc_common_name requires that the user go into Windchill and rename each item one-by-one in order to fill out a BOM in a drawing in Creo P2.PTC, please allow renaming of ptc_common_name directly from Creo Parametric.
config rep_w_rule_optimize_download to work better with non-master reps.Opening a simplfied rep of an assembly in 2009 in WF5 opened in 210 seconds. (We had a case open and the number of calls was identified as the main contributor.Now in Creo Parametric 2 in 2014, the same assembly and rep opens in 300 seconds. This idea is asking for Creo to more efficiently create the packages to download into the users workspace when opening objects not currently in the workspace.
If two faces on different parts need to be aligned, why can't they be done in the same command? Currently you have to start the command twics.
Creo Parametric could use a Performance Diagnostic Tool to support large assembly management and general system performance. This could be a localized version of the Performance System Monitor for Windchill but at a much lower level. For example I have several drawings that people have created that take 30-60+ minutes to open. They load up my memory to it's limit. These aren't our biggest or most complicated models yet they take longer to open sometimes. It would be nice to figure out why. Is the model that big. Is there 2 assembly models attached to the drawing, different simplified reps... A sort of hierarchal breakdown on what areas are leading to the problem would be ideal. This would be helpful for Drawings and assemblies, or those parts that just seem to cause problems. Just a rough concept but I'd expect it to have more info: Drawing (Memory: 500MB) *Using Multiple Simplified Reps of the same mo
We have got few nice functionality for curves like in sketch "Convert to spline" or in model "Copy Approximate" to convert continuous curves chain into one single 3D curve which are very helpful to obtain smooth surface base on that curves.But sometimes it isn't possible to have as result single quilt without merged surfaces.Sometimes it is hard to use flatten quilt or other nice feature if the quilt isn't single surface, so I wish to have also new feature or an option inside merge feature to have as a result one Quilt without inside edges at all.Here is simple explanation by screenshot - this is just fast and simple, but can be more inner surface edges:
With the varying mass properties reported in sheetmetal due to forms or arbitrary bend allowance settings, sheetmetal mass properties, specifically volume and sub-categories, should report the mass properties of the flat pattern with flattened forms.If the flat pattern feature exists, which is always the last feature, the either new mass property variables are created or existing ones are used to determine the actual mass properties of volume and mass. This will make up for the fact that Creo does not compensate stretched material in the forming operation, and will forever clear up the discrepancies between flat pattern and formed mass properties. For some, this is critical information and should be part of the core product rather than a user created function.This relatively simple request should bring Creo into the fold of other systems and remove the ambiguity and inaccuracy described by many users.
Right now untrim results in a whole series of disconnected patches.If you are trying to copy and untrim a bunch of patches you're kindof expecting to see only the single side edges untrimmed.Maybe an option like 'explode' all patches should be present.
I found myself wondering if it wouldn't be nicer to have an ability to throw in the checkpoints i need to do, kindof like a to-do list. Then go fill them out. Then as i check in, the to-do list can be updated and so on.Also each of the exploration checkpoints could be an experiment. Why not provide a mechanism for simulate to be ran on all the experiments. Kindof like a manual DOE.Also automated creation of a series of checkpoints (like making a number of instanecs using the wizard) so we can initiate a whole bunch of range studies.
I think this extension could possibly be a killer app. However i've been looking at GIT for SW dev and i think current HW dev design work is also highly non-linear. Thus it would be ideal if i make a change to both part 1 and 2 in checkpoint 1. And then change 1 and 2 again and snap checkpoint 2, it is quite probable that mgmt will ask for the changes you made to part 1 from checkpoint 1 and the changes you made to part 2 in checkpoint 2. Within reason it feels likely that i should be able to cut and paste the changes from both of these checkpoints to a 3rd checkpoint to more efficiently take mgmts' decision forward. As another side note, i wondered if the tmz could be made multi-user in nature or have tmz inside tmz to allow explorations to take place at a system AND at a lower level point of view.BTW aweseome rev1 functionality again.
I had the opportunity of attending a hands on session yesterday and found myself wondering if in the future we could handle newer versions of Creo in the same way that Solidworks/etc can be handled. Assuming we were on Creo 3 now and Creo 4 comes along, it would be nice to let the folks who can use that tool for good go use it without totally disrupting the design chain. Maybe this could be nicer than the GCRI method. Similarly wouldn't this be another approach to allowing direct modellers and parametric modellers to kindof coexist without messing up feature trees too bad?
On my opinion, the icons for the buttons CHANGE_HATCH_DISTANCE and CHANGE_HATCH_ANGLE have to be changed. The images are not corresponding to the commands. It is confusing. Here is what I propose:CHANGE_HATCH_ANGLE old:CHANGE_HATCH_ANGLE new:CHANGE_HATCH_DISTANCE old:CHANGE_HATCH_DISTANCE new:
I wish to have ability to change at least colour within the same annotation to see following result:Word1 word2 word3at the moment not only pen table is the barier, but also current functionality, because whole annotation can have only one colour!To obtain the required result you must split annotation into each separate, but not more than 8, because pen table is the limit... this isn't funny... please vote also on this idea - strongly connected to this one:http://communities.ptc.com/ideas/4534
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.