Recently active
I am using Creo Parametric Release 6.0 and Datecode6.0.4.0Threaded holes are automatically placed on our DTM_AXIS and HOLE_AXIS layers. Our policy is to have all layers turned off when the drawing is complete. This layers off the cosmetic threads. Removing these axes from the layers reinstates them in the drawing.So I guess the solution is to not have these on a layer in the first place. How do we stop just the hole axes from being added to a layer in the first place or is there a better way to handle this situation? Kind regards Greg
How to draw a Squircle shaped cylinder in creo.
Hi all, Using Creo 4.0 I would like to ask some advice about how you would constrain this (red brownish) U shaped bracket for the shown load situation. The bracket has 2 holes with a pin in it (so it can rotate). Both holes are loaded with force F/2.Force F is applied on a bolt that is placed in a screwthreaded hole in the bracket. I have modeled the bracket like this:For the pin hole, I use a bearing load with force F/2. I use a displacement constrain to implement symmetry on the cutting surface: I use a surface region to constrain in the axial direction of the screw hole. (cylindrical CS). This model calculates fine, but as can be expected, I have a stress peak at the side of the surface region.Not sure if that is entirely realistic. A slightly different approach is to exchange the screw hole by an 'embedded' bolt, and constrain the tip of the 'bolt': This results in a (lower) stress peak at the indicated spot below. Perhaps a
Is it possible to point deployments at a central, config.pro file? Currently we'd overwrite the local version on the computer if a change was needed, but can it instead point to a version say hosted on a server to read the settings? Also can you alter the settings before deployment, so the version of the config.pro file deployed already has these changes? Thank you.
Hi,I often encounter "circular references" problems,although it can be laid aside because often this problem doesn't has fatal dangerous to my models,but the notification looks uncomfortable to me. But when I take a deep insight into this problem,I always failed to find which dependency relation is the cause,when I click to open the notification center,I only see the root node listed below "circular references(1)". So I want to ask for a method to troubleshoot this problem or any modeling principle to avoid this problem? thanks a lot.
Hi, I know this post is old but want to understand what did it end up going with? I have 3 files. The first is a skeleton with the dims i need to drive The next model is the cast version last is the machined version. I need to be able to change the parameters from the skeleton model but from within the machined file. TIA
HelloI want to know if its possible to select fictive line on 2d surface: generated with divised line ?Config option?It is only possible by copying a part of the surface With 3d curve and variable sweep its possible because creo generate a isoparam Thank you
Hi,Does anyone have a solution when exporting a drawing to .DXF format via Web.Link, the file name is always written in lowercase letters. How to get the file name to be written in uppercase letters. Part of the code is as follows:...var DXFOut = pfcCreate("pfcDXFExportInstructions").Create();CurModel.Export(FileName.toUpperCase(), DXFOut);...No mater what I always get filename od disk written in lowercase.,But if I export to PDF format I can get in uppercase format. Any idea, solution?
We've created a lattice structure using the Engineering - Lattice tool by first extruding a solid and then replacing it with a lattice. Our lattice is a formula-driven gyroid with Replace body with lattice checked. When we export the part as a STL-file and try to import it in to our CAD software it fails.When checking the geometry in meshlab using Filters - Quality, Measures and Computation - Compute geometric measures we get :"Mesh is not watertight, no information on volume, barycenter and inertia tensor" Any ideas on how to proceed? PTC CREO 8.0.4.0
Hey there. This is my very first post 🙂 I have made a drawing of a car sign. I did my best. Then I needed help to bend the sign i two directions, so I got help from a **bleep** i know who teaches in Creo. But it is not quite okay yet and I can't get in touch in the "teacher" now. Is there anyone whom I can communitate with and send the drawing to. RegardsMichael
I have ModelCheck configured to issue an error and prevent check-in if a part does not have a parameter set to a known value or does not exist. If I create a new part and delete the parameter, ModelCheck functions as expected, and the check-in is blocked. If I have an existing part that got checked-in before I enabled the check for the parameter, it allows the check-in to go through and issues no error or warning for that file. The existing file was loaded into Windchill with the old ModelCheck rules, before I tightened them for this parameter. When running ModelCheck interactively, it still does not generate an error. MC_Verified is set to YEs from the prior check-in and we have set the value for ModelCheck hours to 100,000. Has anyone else seen this behavior before?
Thanks,
I have some suppressed features in part model. I want to enable that suppressed features in assembly level. (Like simp rep). Is possible to do in part level simp rep? or other option.But I don't want to create an instance.
These options are too short, not a complete word, and the PTC help document has no relevant explanation, I don’t know what they mean, can anyone tell me, thank you! I hope that the PTC help documentation can add explanations for all these options and sub-options.
for an existing drawing view, i want to change its rotation of that view . For the existing drawing sheet I want to do modification in its view orientation ,but rest over dimensions will remain unchanged (should remain same). only there shouldbe a change in view rotation & no need add or giving dimensions again from beginning.Is there any tool or feature to perform this activity ?(actually i am making a assembly drawing of a model) Plz kindly reply to this …..
I bought a license "Creo 9.0 University Student Edition Premium License". After I configured it I still could not create Mold/Cast Cavity. What should I do then?
Hi,I'm starting to study the creo welding module.I have a question. Is it possible to change the welding standard from ANSI to ISO in a model?I've done several searches in the guide and on the internet but I haven't found a solution.- First attempt: If I change it from the welding module preferences menu, the change does not take place. - Second attempt: It seems that the "weld_ui_standard" config option only affects new models. - Third attempt: The "weld_symbol_standard" option in the drawing options has no effect... Can anyone help me?Thank you.P.S. I use Creo 9.0.2.0.
These options are too short, not a complete word, and the PTC help document has no relevant explanation, I don’t know what they mean, can anyone tell me, thank you! I hope that the PTC help documentation can add explanations for all these options and sub-options
I have a drawing that on it's second page uses ordinate dimensions. Out of these, the "X" value .000 dimension lost the reference and is now colored purple. If I erase this baseline dimension, them all other dimensions associated from this base point go along with it. I want to avoid this, is there a way to redefine the dimension so that it is no longer purple or perhaps a way to disassociate the children dimensions form it?
i have a big assembly with a lot of fasterners. many fasteners are the same. those share 1 bom balloon number.some fasteners are only used in specific configurations of the model. in this 1 view i have 1 (nut 1 = N1) lock nut that is always used . and 1 (nut 2 = N2) that is only used in configuration Xwhen in configuration X i need this view to have the balloon on N2. the balloon with the same number for N1 is already in a different view when i have it all set up correctly in configuration X and save it it is fine when i open itit is when i go to configuration Y that i see that the leader of the ballon from N2 has jumped to N1, the balloon itself is still on its spot so i basicly have a line running tough my view.when i configure it back to configuration X the leader does not return to N2.this is very annoying. i need the balloon AND LEADER to stay with N2, and when N2 is not used i just need it to dissapear. just like the balloons do for normal parts (often only on
I am trying to recreate a velvet endmill, and frankly, I have no clue where to start with modeling this. Usually, I use a helical sweep to model normal endmills, but this has me stumped.
Hi, We work with Inventor for 3D modelling and when these models are viewed in CreoView Lite, it opens upside down by default. Which setting do I need to change in CreoView to open models with the Z-axis pointing upwards?
Hi, I am trying to insert a custom component by using the Insert Component option,But I am not being able to select LOCATION ON THE CABLE, any help is appreciated. Thanks in advance! Regards,Vinay
I have 6 feature/groups in creo part model. please find the attachment.I need to resume only one group/feature and suppress all others according to my input parameter using Pro/Program.-----------------------------------------------------Example:Let my input parameter is a string: M12Then Resume Group_M12 and suppress Group_M6, Group_M8, M10, Group_M14 and Group_M16.-----------------------------------------------------I need to execute this by using the Pro/Program.Could someone support by writing a program for this case?
Hello, Does anyone know if it is possible to get Matlab Simscape to work with Creo 9.0?I am using the student version since I need this for a project.I manage to get it to link but I seem to be having trouble getting it to work.For some reason, I get an error when trying to generate a XML file. Any help will be appreciated,
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.