Recently active
While using Creo 9 Mechanism Dynamics Option (MDO) for analyzing design system, user is getting the error "Mechanism Dynamics is required for this analysis type". After re-installation it worked. But when Creo is closed and re-launched, again the dynamic function is lost.Because of this issue, user cannot close Creo session. If closed, this is lost.
We have both Design Essentials licenses and Design Advanced licenses. The one difference is that Design Essentials does not have the optional module Assembly (#6) in the list of modules. We can create assemblies with the Design Essentials license, so there has to be something more in the module besides just assembly creation. Does anyone have better definition of what is provided by using the Design Advanced licenses with the Assembly module over the Design Essentials license?
Hello everyone, first of all. I want the spring in the assembly part I'm using to be movable. I've tried a lot of videos on this topic, but I couldn't assemble the springs I made the way I wanted. Can you help me with this?
Does anyone know how/if possible to save a part file or assembly to an older version of creo? Example: a part or assembly made in Creo 7.0 save a version that can be opened back in Creo 6.0
Hello, Does anyone used Creo on MS Azure ? If yes, can you please describe your rendering experience and the hardware specs you are using ? Thank you.
To have config option to enable draw scale to dynamically update according to the scale defined in the latest view placed in the Drawing. This should happen irrespective of any representations used in the view. Business justification: Whenever a view is placed under the config option default_draw_scale with value -1, the view will get placed with scale defined by creo based on sheet size the overall dimension of the 3D model. the Default value of the draw scale in the Title block do not get changed automatically while the scale of the view will be different than draw scale. This leads to confusion when sent to vendors.
When clicking the RMB on a Section within a Geometry Feature, allow the section to become a Sketch feature placed before the feature it was associated with. Then replace the geometry feature's Section with the newly created Sketch feature.This idea will allow references from once internal sketches (sections) to be accessed during new feature creation by making the sketch unhidden. Currently, section features, for the most part, are not accessible when they are created as internal sections.The other 3 options are already available; You can unlink an external sketch to make it an internal sectionYou can replace an internal section with a sketchYou can delete external sketches once it is unlinked in a feature while preserving the model.The only thing we cannot do is simply make the Section a Sketch with a single command.The work around is not pretty at all: Edit definition of the section and save it as a .sec fileCreate a sketch from the saved .sec file and re-associate it (an
Hello friends, In Creo Elements Direct Modeling 19.0, how can I measure distance between the axes of two holes?Every time when I want to measure the distance between axes of two holes, I only can get the minimum distance between two holes.
Hello. I am wondering that if it is possible to manage the assembly references in part mode. For example, i would like to open a part in assembly mode, then i will replace the reference for that part in part mode.
I have a fairly simple drawing with a repeat region showing mass properties (see attached screen dump)I have one column for the total weight (part weight x rpt qty).To avoid adding assembly weights to the parts weights, I have set the assembly weight to zero and the column only list the parts' weights.The total wight of the main assembly is calculated separately and listed in the drawing head asTotalvikt = 154,02 kg.When I add the weights in the column they add up to the same as Totalweight which is what I would expect.However, when the repeat region summation does the same adding up it gives the result = 93,05 kg.I have tried various assemblies but there is always a difference between Totalvikt and the summation result.I have not been able to find any logic between the two different results.Can somebody tell me what is wrong?I am using Wildfire 3.4HELP!!
Hello, everybody:I am trying to generate a PVZ file using simplified reps to only show a part of a bigger assembly. In the Annotate tab of CREO I have the correct components on display but when I export the file to CREO view I get extra components that should be hidden. Any idea of why this happens and how I could fix this? I have attached photos of the CAD view and the PVZ output below.Thanks in advanced for the help 🙂
Hi alls,I'll have to go and work at my client office soon.I must use my notebook (Win 7 x64) with Wildfire 2 and Intralink 3.4.Now, I'm working with Creo 2/3, what a big change...So, I'm wondering if those a little bit old softwares will work on my Win10 x64 computer or must I install an older OS (win7, x32/64... ?)Thanks for any advice,Dominique
I could open parts fine in Creo 3 M120 / WC 10.2 fine for years but then recently I get the "cannot be retrieved" error whenever I try and open something from my workspace. I have tried the following so far:1. Using another PC - same error2. Logging in with another user on my pc - works fine3. Reinstalling Creo 3 M120 on my pc - error persists4. Clearing cache - error persists5. Deleting all existing workspaces and creating a new one - error persists6. Deleting user and re-adding in WC - error persists I think it must be a Creo agent issue or something similar? I have run out of ideas...
I would very much like to add a column to my BOM then make the lines invisible. I want to have one or more parameters attached to the BOM but off the page of the drawing because no ones going to like having a bunch of lines on the page to the right of the BOM like a column didn't get printed.
Hello i want to add new sizes for threaded holes. For example i only have until M16x2 and i want to to do a M24 hole. See picture below.
Software: Creo Parametric 7.0.10.0 I want to assign some sheet metal design rules and have created one. Can we verify those rules in the model. I tried using "MODEL CHECK Rule Check". But I'm getting this error "Cannot read rules from file". I have saved the rules in this filename "design_rule_test.rul" (as saved from Model properties). But in creo documentation, it is mentioned that the file should have ".rule" extension. I have also created "RC_MODEL_TYPE" parameter. How to do this correctly. Am I doing something wrong?
Hello,i am new to engineering and tend to get the simple yet difficult things confuse. If you ever have a parent/children drawing for updates, whats the best way of remembering it?Ex: if you have a casting drawing which is referenced on a machined drawingEx: if you have a complete finished good along with packaging and let's say a sub component in a finish good changes, will it rev up packaging?in theory, in my assumption.. if a parent is affected, all children gets affected.. if a child 1 gets affected and there are other children underneath it... the parent won't get affected but anything under child 1 will. Please help with feedback. I appreciate your time and efforts
Dear Team,I have created a custom parameter into the assembly, Now I want to call this parameter into BOM table. I know how to use repeat region, but I am not able to call the assembly custom parameter into drawing BOM table. Please help.
Please see https://www.ptc.com/en/support/article/CS311063.It turns out View Adapters are currently not supporting different representations for publishing Inventor assemblies and always visualize "Master Rep" only.It is even documented that way in "Creo View MCAD Adapters Installation and Configuration Guide", see the attached screenshot. Sadly that's not acceptable for our users and use-cases within Windchill. Designers expect the published assembly to look like they saved it, showing the active representation in Inventor, not always Master. It's dangerous too, because components might have to be surpressed, different color-encodings are used for certain components, etc. All is lost by blindly visualizing "Master Rep". Please consider implementing proper behaviour (like implemented for Creo) in a future release. Thanks!
I cannot find the setting, I believe in the DTL to change the default behavior for new projected views. What we want is for the view to come in WITHOUT any of the annotations displayed. I have seen this behavior in the past (at different company/installations) but we see all the annotations that are in the acceptable orientation display and we are forced to do a bunch of cleanup work. We would like to eliminate that. thanks in advance!
I will rendering an animation... and i will use FFmpeg....In the Help-Center is only this litte text.... Add an AVI codecSeveral AVI codecs are defined in the customization file ani_customize, which is found in <installationdirectory>\personality\sd_customize\AdvAssembly_Parametrics. You may add a new codec to this file if desired. Please review the comments in the file for more information. Now in the "ani_customize" i will add FFmpeg to creo.... but it dosen't work... FFmpeg is installed on pc. How does it works? Any tutorial available?? Here the code lines:;; customize the AVI codecs available for save animation (codec must also be installed on PC);; First string is the 4 character code (i.e. "MPEG") - second any description;(anim-add-avi-codec FourCharacterCode Description)(anim:anim-clear-avi-codecs)(anim:anim-add-avi-codec "FFMP" "FFmpeg")(anim:anim-add-avi-codec "MSVC" "Microsoft Video")(anim:anim-add-avi-codec "DIB " "Uncompressed") I hope
I am looking to see if its possible to delete this "Root" designation in the PVZ. Highlighted in picture below.
A "snap line style": a line visible in the drawing but not printable.This line style should be useful for table lines, 2D Geometry, custom symbols BOM balloon notes...
hi All I am facing an issue with a 3D assembly. Everytime I open the assembly with a simplified representation (not Master or automatic) and regenerate the model, the model changes partially to wireframe (not all parts, only some of them) and these parts are not selectable anymore. does anyone have and idea what the problem here is? Creo 7.0.12.0 with Windchill 11 thanks in advance
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.