Recently active
Hello all, I am a fairly new user to Creo, so bare with me with some of the terminology, but I am having an issue with exporting a 2D sketch in Creo. When I export the file (shown in the pictures attached) and import it back into Creo the file shows up blank with only a picture of the DXF file that I was trying to make. I have tried importing the DXF on SolidWorks as well and this also results to the same issue. Does anyone know why this happening? Thank you in advance!
The system colors, for example system_geometry_color, can be set via specifications in a file. For example, I use "syscol.scl". To the best of my knowledge, there is no documentation of what parameter names are available for these settings. Equally important, it is not clear what effect setting any of these parameters will have. I'm wondering if anyone has any documentation of the following: (1) Parameter names (2) Screen elements affected by a given parameter (3) Syntax for the settings file, i.e. what alias_sec_dim_strong_color_to means, the color value ranges, etc. I had asked this same thing as an Idea for it to be added to the Help documentation. It was pretty much ignored. I naively thought that such things would be documented and available, but that does not appear to be so.
I am using :Creo Parametric 7.0.7.0 Windows 11 Professionnal Version 22H2I have a search.pro file and I specified its location with the search_path_file option in the config.pro file. The locations contained in the search.pro file contains standard parts that will never change. My issue is that when saving an assembly, I would like to save all the parts but not the ones contained in these locations. Is it possible to achieve that and how ?
I am creating a UDF of the J1926-1 feature on the end of solid round bar.When I run the UDF on other locations, the revolves and extrudes 'flip' and do not follow the way they were created. Using the hole command, I have been able to create the spotface, drill depth, etc without any issues. When I run the UDF, the helical sweep cut (thread) of the feature flips. I have created other UDFs of this same feature and all appear to work correctly. Any ideas of what I am doing wrong?
I am using Creo Simulate Release 4.0 and DatecodeM150I have parts upon which we ran structural simulations in the past. I wish to now run a fresh simulation in assembly mode. When I have my assembly in session, and go to simulate, I get all these failures due to bad constraints and load sets. I want to start fresh and try to use HOME / SET UP / NEW SIMULATION MODEL. However, New Simulation Model is greyed out.I also cannot delete individual constraints or loads in the model tree.
I'm trying to create a drawing of a multi-body part, with a bill of materials table, like an assembly drawing. (I've created a multi-body part as it's quicker than modelling an assembly.) I've named my bodies and created a BOM table using one of the built-in templates, which generates a unique item number per line, but I can't figure out how to make these item numbers appear as balloon notes.'Create balloons' on the toolbar only seems to work for components, not bodies.Is there a way to make this work? Or do you just have to create manual balloon notes?
I am using Creo Parametric Release 9.0 and Datecode9.0.0.0In my main assembly I am trying to assemble jumpers assembly as a flexible component. Earthing jumpers are two sub-components, so I am trying to assemble in different lengths and directions. I am able to constrain distance and it works fine, but direction of the subcomponents will be different, I cannot rotate subcomponents, only earthing jumper rotates. For example, in the first position Earthing jumpers have two subcomponents, component 1 should have an angle offset of 35 degrees and component 2 should have an angle off set of 65 degrees. In the second position, in the same way, component 1 of Earthing jumpers should have an angle off set of 45 degrees and component 2 should have an angle off set of 25 degrees. Let me know what is the best way to keep them consistent.
Dear PTC Team, I have created & modifed on Huge ASsembly file for one of my project. After couple of days, While Opening same Assembly file again for some modification, Creo 10.0.2 software keep getting crash. Do you have any solutions for such Crashes.
This occurs when clicking "OK" or deleting datum planes, the Regeneration Progress window overlays Creo and wont let me continue. Solution is still to end it all through task manager and deal with the file loss. I don't want to run into this problem in the future when I'm working on something much more time consuming, does anyone know of a solution?Thank you for looking into this for me.
I would like to know how to import the CSV data into MODS when I generate several combinations in other software, in this case it would be several points, but Creo comments that the imported data is wrong, would there be a correct way to import?
I am using Creo Parametric Release 8.0 and Datecode8.0.5.0Hello,I will write Gpost for Siemens 840 D control units, but I didn't get the gpost output as belowCS_TOOL("T60")CS_TP("T11")When I got the gpost output, I got it as belowT2 M6T1How can I change Tool output as CS_TOOL and CS_TP in the GpostCS_TOOL= Tool to useCS_TP=a next tool
I had the following request in today from a customer. How do I delete the references used in an NC step, Using the references right mouse click doesn't allow the option. Customer on Creo 4 F000, I have also tested on 10.0.2.0.Only way seems to be to edit the Tool Motion entries.
Currently running 9.0.5.0 on two work stations and the issue as stated in the following post was not resolved: https://community.ptc.com/t5/3D-Part-Assembly-Design/Cursor-not-visible-in-family-table-cell/m-p/875073/thread-id/129131#M129649 Going to either open a new case or see if the previous one can be reopened. (Previous case: 16880414)
a) Does anyone have experience with the stability and performance of Creo Parametric on an Intel Core-i9-13900 or 14900 CPU? b) what motherboard and chipset is advised?c) There is also a chipset which supports ECC RAM memory. Is it needed for a good stability of Creo ?d) Is ECC RAM needed for a good stability of Creo Simulation Live ?e) How is the sound level? Is it silent or a lot of noise when high performanceis asked?f) How is the experience with over clocking the CPU to about 5.8 GHz regarding above questions? g) Comparing the specification with Xeon processors the Core i9-13900 may perform better.- Is this also the case in practice?- Is this also the case when not using the over clocking?h) Is Creo always using the Performance Cores of these CPU and how is this managed?i) How reliable is the Core i9 and what about lifetime when over clocking with respect to a Xeon processor?j) Is over clocking possible or can this performance increase not be earned and is it downsc
The middle mouse button does not complete the feature (example line chain). I was on Creo Parametric 9.0 and just downloaded 10.0 both the student edition. It was happening on the tail end of 9.0 and continued in 10.0
Good afternoonI am using Creo Parametric Release 8.0 and Datecode8.0.7.0I' m using CreoJs in order to automate some tasks in Creo.From CreoJs, I'm trying to make a call to Windchill REST services.It works well for a GET request by using "downloadJSON" function from Additional API Features Introduced in Creo.JS in CreoJs user guide.My issue is when I want to do a POST request.I use "uploadJSON" function to be able to send a JSON object with body definition and the nonce token in the header.It always return an Invalid Nonce token error.Is someone could help me on the correct use of the uploadJSON function to send a POST request with headers?Or what are built-in function of CreoJs to perform a POST request?Here are the errors that I faced"statusMessage":"400: {\"error\":{\"code\":\"INVALID_NONCE\",\"message\":\"A potential security problem was detected. Refresh the page and try again. If the problem persists, contact your administrator.\"}}"
As per the original post. Hey, Is the play trail file option not available for student version ?
creo 4.0 m100toolkit visual studio 2015 not working
Hi, I am new to Creo. I have tried to use the Spline tool and I can't add another point OR delete an existing point upon creating a spline. I am usually forced to delete the spline and recreate it in case I want extra points or fewer points. Is there a way I can edit the spline i.e. adding another point or deleting an existing point?
Hi everyone. Is there any option in CREO Parametric, to 3d-draw flexible components such as hoses and cables after their natural properties such as weight stiffness tension rotation etc.? I want to draw some water hoses in a machine, so that the hoses can behave after their real structural propertires, not only forces by my restrictions. Thank you so much in advance for your help. Br,Hasan
Hello,am I the only one who gets grey borders every now and then when extracting 2D figures from Creo Illustrate to bitmap (300dpi)? Best regardsRamon
I am using Creo Parametric Release 4.0 and DatecodeM040User is not able to fetch NRB templates.Here are the errors that I facedUser is not able to fetch NRB templates.
how to enable this option in creo9.0
I am new to combination states. When I create a new combination state, all of my default datum planes get hidden and I can not unhide them using layers or the model tree. But I need them because I want to move dimensions to those planes. Does somebody maybe know how to bring back the default datum planes when you just created a combination state? Thank you for looking into my question!
Hi everyone,What are your favorite features, shortcut, or lesser-known capabilities in Creo that has significantly improved your workflow? I wanna know. 🙂
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.