Recently active
Add a RMB "zoom to" in the Find collection results.
Change of representation of the structural comparison command of ModelManager. The notation "null" is not common. I want to display a "未入力" (Meaning not yet been entered) in the Japanese environment.
Add a config.pro option to switch between "define simple thread" and "define standard thread" as standard option while creating a cosmetic thread.
1. Allow double click on results window legend min and max values to change cut off values. 2. Fix issue of Results Window Legend not retaining Upper and Lower Limit Values that were set (cut off values) for the following changes to the results window... - When hidding or showing components in the results window for assemblies the legend resets the limit values - when changing from vm to maxP stress the results window legend resets the limit values that were previously entered
Add ability to save simulate results windows Templates for design studies that have multiple load cases where all or some of the cases are being shown in the results windows. Imagine doing multiple iterations on the beam and needing to show all four results windows for each design iteration. Currently you are not able to save a template containing all of the view shown below to be use for future runs where a part may be changed in the assembly. All 4 windows (load cases) need to be shown for reporting purposes. This will help address the following error message..All of the windows for inclusion in the template must be from the same study directory (Error Message)
In PTC Creo Simulation, it would be extremely advantageous to be able to specify run settings on a design study basis. By doing this one would be able to specify a unique previous mesh for a number of studies. Then one could run a batch file over the weekend for one model with multiple mesh configurations.Also, one could specify the design study file location on a design study basis. This would allow a local directory to be specified for design studies currently being run and another location for archived results when local drives become full.David
Currently one can only used results of a previous steady state analysis as initial temperatures for a transient thermal analysis. One can use the results of a transient thermal analysis as input for a structural analysis but not for another transient thermal analysis. Therefore, if one is determining the temperature distribution in a valve and the flow conditions change, one is out of luck as one cannot either vary the convection coefficient with time or start a new analysis with a different convection coefficient using the result of a previous analysis.
I'm using Creo Parametric 2.0 M120.In a medium-large assembly (5800 parts) if Smooth_Line option is enabled, it takes a long time to make an offset cross-section (+/- 5 minuts).If Smooth_Line option is disabled the same cross-section can be made in less then 1 minute.I have made tests in some Hardware scenarios, the worst machine configuration was an "Intel Core I5 - 4G RAM – 1G graphic card" and the best machine was an "Intel Core I7 - 32G of RAM – 2G graphic card", in both machines the results was similar.Its important to me to work with Smooth_Line enabled but, it need to be faster.
Currently only one option to automatically create resulting objects is available when change a notice is being created.This is the revise button.This creates a new revision and in our workflow sets the resulting newly revised object back to In "Work status" from its "Released" status which means the previous revision is still the Released revision until the change has been completed and then the newly revised object gets upgraded to "Released"However if I want to create a change that will have a minor effect on an object such as a spelling mistake on a drawing or an incorrect mating in an assembly etc. it does not warrant a full revision it makes the transition by iteration for example V 1.1 to V 1.2 instead of V 1.1 to V 2.1.This is not currently possible. As there is no way to up-iterate then no resulting object can be created. If the Object in question is at"Released" then the change is happening to a "Released" Object (in our system no one can check in a modified released part). It
Avoir la possibilité de choisir le style d'affichage (ombrage, ombrage avec arêtes, lignes cachées, sans lignes cachées, filaire) différentiellement pour chaque composant d'un assemblage dans une mise en plan. Cette fonction est disponible dans un assemblage (cfr 'Assemblage.jpg') par l’intermédiaire de l'onglet 'Display' du 'Gestionnaire de vues' (cfr 'Gestionnaire des vues.jpg') mais pas dans la mise en plan (cfr 'Mise en plan.jpg'). Have the possibility to choose the display style (shading with edges, shading, hidden lines, no hidden, wireframe) differentialy for each component of an assembly. This function is available in an assembly (cfr 'Assemblage.jpg') using the tag 'Style' of the 'Manage views' (cfr 'Gestionnaire des vues.jpg') but not for drawing (cfr 'Mise en plan.jpg').
Would it be possible to create surface and volume regions at the assembly level so that they are not reliant on them being created at the part level.This would be useful where you want to create a surface or volume region that splits across multiple parts in an assembly.
Derzeit ist es nicht möglich, Geometrische Produktspezifikation (GPS) – Dimensionelle Tolerierung – Teil 1: Längenmaße nach ISO 14405-1:2010; Deutsche Fassung EN ISO 14405-1:2010 zu erstellen. Problem ist bei PTC bekannt C12507314, SPR 1909487; SPR2119259 aktueller Stand der Norm wird angehängt. Die Symbole sind in den Tabellen 1 - 3 auf Seite 19 und folgende dargestellt. Beispiele wie das in den Bemassungen auszusehen hat, sind auch in der Norm dargestellt. Bitte alle Möglichkeiten, auch die Darstellung von eingeschränkten Teilbereichen berücksichtigen. Im Anhang A sind Proportionen und Abmessungen graphischer Symbole dargestellt
When importing a step file or opening a native file, Creo splits a single surface with G2 discontinuity into multiple surfaces. I would like an enhancement of a config option to NOT split the surfaces.WF5 and Creo 3.0 are the ONLYsoftware that will split the single surfaces into multiple surfaces. This normally wouldn’t be an issue, but when we bring this geometry intothe Mold Design Extension, all those extra edges and vertices cause geom-checks and splitting issues.Here are some examples of "Other" software importing the same file. Note the multiple surfaces in the PTC products.Here is the file brought into WF5Here is the file brought into CreoHere is the file brought into SolidWorksHere is the file brought into NXHere is the file brought into 3D Evolution
I think it would be useful to have a 'back' button when searching for an instance within a model with a family table when using the File>Open command.Currently if you 'browse' to the wrong level of a multi-level family table you can't go back up the levels to allow you to search a different area. You have to cancel the File>Open command and start again.
be able to create an accurate profile of the geometry using the silhouette mill window feature.
"In IsoDraw 7.0, Save As will default to the folder where a particular file was retrieved. In 7.1, ‘Save As’ defaults to the last navigated folder"Nous voulons avoir la possibilité de changer ce paramètre dans les prochaines version et ainsi pourvoir faire un "Save As", "Export" etc ... et tomber directement dans le dossier du document ouvert comme c'était le cas en version 7.0
Creo n'indique pas l’affichage des ’’ pour les cotes en pouces alors que ce symbole est universel pour reconnaître l'unité !!Cdlt
Standard parts will never cut into views. If you such parts exclude they still display as outline in views with full (unfold) cross section. That’s not like the ISO Standard.
Hi,Why file == > close window icon in Creo Parametric 2.0 is a "folder" icon, can you replace it back to a cross icon?Its not logic, because its a cross icon in Pro/E wf4 , and Creo parametric 3.0 also its a cross icon.This folder icon is very disturbing for the new users, as they click by inadvertence on the "folder" close icon when wanting to open a file.Many of them are asking for the return of the old one.Thanks in advance.
Hello, we need DWG/DXF Export JPG as embedded pictures from Drawings (act. export JPG Files per File)Based on CASE CS208576 & C12593543Michael Engelhardt (IT Manager CAD/CAE)Mitsubishi Hitachi Power Systems Europe GmbH (Germany)m_engelhardt@eu.mhps.com
ich möchte hier die Kundenwünsche deponieren:Ich bin Nutzer von Creo Elements Direct 3D Access. Ich arbeite im Managementbereich und nutze diese hervorragende Software vor allem als Viewer, für Präsentationen und zur Erstellung von Dokumentationen (Screenshots). Ich nutze sie NICHT zum Konstruieren. Ich komme gut damit zurecht, bis auf 3 Punkte welche mich ausnehmend stören: 1. Farben bearbeiten Ich möchte zur besseren Darstellung in Dokumentationen gerne die Farben von Teilen ändern. Dies ist leider nicht möglich. Mit dem Workaround über das Rendering-Modul ist dies zwar begrenzt möglich, aber sehr umständlich und sehr eingeschränkt. 2. Facettengenauigkeit Je nach dem wie der Ersteller des Modelles die Facettengenauigkeit eingestellt hat erscheinen runde Bauteile rund oder als Polygon. Bei niedrig eingestellter Facettengenauigkeit sind Screenshots für Dokumentationen hässlich. Ich möchte die Facettengenauigkeit einstellen können 3. Strukturliste bearbeiten Die Strukturliste kann nur s
Hi,I have an idea about Auto Backup at Working directoryIn my current organizations we work on very heavy Assemblies , on working upon them we might forgot to save & hence it Creo Crashes away.After above incident we think 'I would have save' , hence Once again we start doing it again.I think this case is common to all the Creo users .I request to PTC to create one settings such that what ever we are working on part or Assembly after a interval of 5 or 10 min , it takes Auto Backup.
We want to display the X direction of Principal axes.Now is indistinguishable of XYZ.
A few versions ago the little green triangle "play" button was added to the UI. The addition of the triangle adds many clicks to my day, as well as having to redo many operations because nothing was reminding me to switch an option. I don't believe the green triangle benefits me in any way, but often frustrates me.For instance creating a copy of a part, but wanting to use Mate Align to position. Preselect a part, right click, Copy, click on the green triangle, mate align...For instance align a face with offset. Preselect a face, click align in the mini-tool, click the Ref Face, click on the green triangle, enter an offset.For instance position a part using Mate Align. Preselect a part, click Position in the mini-tool, click on the green triangle, click Mate Align...For instance pull with draft. Preselect a face, select pull face from mini-tool, click on the green triangle, add Draft Angle...For instance creating a copy of a part, but not immediately realizing I'll want to change the ow
We would like to be able to 'Copy' a view within an Annotation drg.The reason is to show different iterations of an assy, using a copy of a detailed view. For example, we would like to show an assy with an ASME flange, ANSI, JIS etc... The parts in the assy can be established using Configurations (drawlist) - or even to a degree, Manage Views. Unfortunately at the moment, each iteration requires all the detail to be 're-added' (duplicated) in each view.This may also require some suggestions relating to the way that dimensions are recognised on views with configurations....!
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.