Recently active
I am having trouble with using the spring idealization in simulate. We are on Creo 9.0.8.0. I read through the different PTC resources and have tried a variety of different tactics to see if I could get a model that makes sense. At this point, I think it has to be a lack of experience/understanding on my part. I attached the files I could. I am at the point now where I will probably just create a surrogate material with the properties I need to continue, but I would like to understand where I am going wrong. I used Spring point-point pairs where the point is on the surface of the model. Tried constraining the points to be rigid and leaving them free. Tried "burying" the point inside the material. Tried using holes in the material with the points centered on them with both rigid and free connections. We tried to go through our reseller to have their consultant help, but unfortunately that guy had some recent medical trouble and is unavailable. Any help or advice would be great
Hello, I would like to know if it is possible to measure radial forces, axial force and moments acting on beam.I' ve been trying to achieve it by compouted measure but than quickly realized that moments which also acting on the same beam completely ruins the result of a calculations. Example:How can I measure radial forces and moments acting on a beam so at the end i can draw two vectors of forces and moments?Example model is in description. Idea of example model is following: model has known forces and moments acting on the middle of the beam(they are given by load case). Measures has to measure the same values given by loadcase. 1N in X, 1N in Y, 1N in Z, -1Nm in X, -1Nm in Y and -1Nm in Z
While working in Creo, I see that the “view change” window opens every time in the assembly parts we open in the Windchill system, which I share as a screenshot below. Although I have corrected the errors in the system, this screen appears every time I open the assembly file in Creo. Actually, I found the solution to the problem, but I want to know what the root cause of the error is. In which error situation this screen appears. Can anyone write if they have information about this subject?
Hello, is it possible to create a flat harness with wires that are not in direct contact?As in picture 1, it is composed of separate wire. the problem is when I decide a start point, I can not go and look for another point on a non-attached wire.I would like to know if it is possible to do everything in one flat harness or if it is necessary to separate each wire that does not touch into different harnesses?
when I try to create a flat harness, with a multitude of wires stuck together, it places the wires in relation to the z axis. therefore, I cannot move my threads so that I can see them all in profile.How to make the flat position like image 2, I can move my segments in this direction
Hi all, I'm in quite a pickle here. I have a multibody part, but the performance is getting horrible (file size is nearly 1gb), so I need to split it up into a new part file for each individual body, and remove unused bodies I have done this part, but now I am left with a single part, but it of course still has all of the features from before the 'Remove Body' feature. I am looking for an expert's take on what the best course of action is. Do I manually go through and delete each feature that doesn't contribute to the end-body needed? I have thousands of features, and about 10 individual bodies that I care about. As such, individually selecting the unused features that I want to delete will be very time consuming. I am wondering if anyone has a better way to do this, or has been in a similar situation. I would appreciate any advice! Thank you,Jeff Houston
Hi everyone,I'm trying to customize our drawings. We need to display the Wtpart version in the drawing format or template.Are there any methods to do this?How can I use this information in the drawing?Thanks!
1. Automotive industry. Mechanical designer 2. Creo 7.3. When showing the diameter of a threaded hole on a drawing, the diameter symbol is shown in front of the diameter dimension. It would be better if an M or G, ... (depending on thread type) would be shown on in front of the diameter dimension. Now the diameter symbol has to be manually replaced by an M. If you forget to change the diameter symbol in the drawing, the drawing is wrong and bad parts are made.4. What is the use case for your organization?5. What business value would your suggestion represent for your organization?
1. Describe the ProblemThe sorting functionality in Creo 11 differs from the normal standard.Untill Creo 11 we named our top assembly with the prefix "0000_".By doing this, that assembly was always shown as the first file either in windows explorer or creo file explorer.This behaviour changed dramatically with creo 11 2. Are you using a workaround?Open the search function and tip in "0000" Then there is only one file shown.3. What is the use case for your organization?Our projects are structured in folders. All our users know, that the can easily open the top assembly just by pressing "Ctrl + O" and "Enter" Since creo 11 everyone complains constantly about opening the wrong files.4. What impact does this problem currently have on your organization?Affects everyone. It is anoying and not logical.
Is there a way to embed a font in an *mi file created by Annotation? I'm afraid that my customer can't display a drawing correctly if he has not that font in his Windows computer. Related question: is it possible to do the same (embed fonts) when exporting to DWG or PDF file format? I'm using Modeling 20.5 on Windows 10
In Creo 10 Is it possible to move the location of the Section to the Top of the ModelTree or even attached this to the Insert Here line. Is there a setting controlling this location.
Hello there, I'm currently dimensioning an epicyclic gear reduction system and I was wondering if it was possible to use the CREO 9 (the version used in my school) parametric functions to dimension this system directly in the assembly. For example, for a given number of teeth on the sun gear, an input torque and an output torque, it might be possible to calculate the planet gear teeth as well as those of the ring gear, and thus directly modify their dimensions. (including the center distance between the gears, the pitch, tip and root diameters, etc.) I've already done a few tests but they didn't lead to anything except errors. Thank you in advance for your answers.
Check out this video on Rapid Product Development using Generative, Additive & Simulation techniquesPresenters: Dr. Andreas Vlahinos, CTO of Advanced Engineering Solutions and Tom Quaglia (Solution Sales)(view in My Videos)
Requirement is to update CAD template of a Project.Initially, these CAD template is created using a source CAD file (drawing) which includes a format file.We have new format file and drawing file. Able to update them from A.1 to A.2?But how will the CAD template created in Project using A.1 version be updated?We don't have an option to choose source CAD file when checked-out? Any help would be appreciated.
Creo: 10.0.0.0 education version Hello everyone, i am trying to create a sweep in the shape shown here:I tried using the sweep blend feature but this results in weird interpolations between the segments. I know that by just sweeping from one section to another the interpolation is linear, but i want some sort of spline as shown in the sketches. Here is the image showing the interpolation. Using the blend feature to control the sketch with trajectories doesn't work properly. I do not know why the trajectories are ignored here, but when i change the sketch to an ellipse at leas one trajectory is followed.Maybe someone can help me with this, since i am out of ideas what parameters i need to change in these features to get my desired result.
Hello, Software used: Creo 8.0.When I set up combined state view in the model I can show different dimensions and annotations in each combined state view, but when add a new view to the drawing and select the combined state view, the annotations and dimensions are not displayed in the drawing as they are in the model. When I select show model annotations for the drawing view it shows every single dimension available not just the annotations and dimension I displayed in the Model according to the combined state view. In older versions of Creo, this was possible, not sure if there is a setting that should be changed in new versions. Thanks,
Hi, I am trying to run the torque analysis on the flange assembly with stiffeners welded using weld features. Unfortunately I am getting errors like "Problems were encountered while preprocessingthe features for the highlighted surface." I could not understand the root cause of the errors. please help me diagnose the issue. Regards,Kishore
If I am not a designer, but an analyst that adds cad to my workspace and labels, takes pictures, makes leader notes for my own reports, is there a way to preserve items like notes, model colors, after i perform a model updated to check new geometry, fasteners, materials. I usually work in a separate self made assembly, so technically i could make items in this assembly that are unique and don't belong to the real cad being built but it seems like notes refer to part features.
I am making sweeps and swept blends using datum points then creating a curve through those points then sweeping along that curve. The datum points exist as one feature, Is it possible to edit the feature to insert a point at the start or halfway down the list? I'd like to add a point after point 7 in the screenshotCurrently I only seem to be able to add a point at the end of the list.I'm using creo 8.0Thanks in advance
When creating a counterbore style pin hole with IFX, the software defaults the 'thru' diameter (labelled 'counterbore diameter' in the UI) to 1/2 of the nominal pin diameter. Our manufacturing standard requires a different diameter - is there a hole chart column that can be used to drive this dimension to a specific value so that the user doesn't have to manually change it every time?We have tested with the known hole chart columns and none seem to work.We are currently running Creo Parametric 10.0.5.0.
1. Describe the ProblemUnable to control the visibility of surfaces and curves (datum curves and sketch curves) on the shaded drawing view by layers of the drawing side in Pro/ENGINEER.2. Are you using a workaround?3D pdf or creo view, format but not possible for all customers and need external application to customise pdf format3. What is the use case for your organization?The display of datum curves and surfaces in the shaded view of a drawing depends on the model or assembly visibility. ptc article describing the issue CS43026 and organisation case4. What impact does this problem currently have on your organization?need external application and productivity loose to obtain the best result: 2 to 3 month for customisation with test Windchill is needed to automatize pdf files etc... dévelopment costs These new fonctionnalities will be good to simplify other case: specific surface, 3d curves for shaded view in drawing many thanks
I have a rivet I want to show in an assembly. The rivet data was 'imported'. In order to show the installed/deformed position, I added a 'deformed' feature that can be controlled by a flexible dimension. The Master Rep displays the 'imported' rivet AND the deformed geometry. I created a Simplified Rep (INSTALLED) which displays the deformed rivet without the 'imported' rivet. So far, so good! The flexible dimension will allow me to display a deformed/installed rivet for different panel thicknesses. When I add 3 flexible rivets into my assembly, I can change their dimension to fit 3 different panel thicknesses (0.75-inch, 1.00-inch, 1.50-inch). However, the display shows both the 'imported' rivet AND the deformed/installed rivet data. When I active the INSTALLED Rep, all 3 rivets default to the original dimension (1.50-inch) and do not hold their flexible inputs (0.75-inch, 1.00-inch, 1.50-inch). Why won't a flexible dimension hold when changing the assembly to a simp
I am currently using Creo Parametric 7.0. I want to switch between open windows using Ctrl + Tab like every single other software does. I searched for a while and found no options in the software or even anyone asking about it. Is there some way I can make this a keyboard shortcut or something? Is this feature just not integrated into Creo at all?
1. Describe the ProblemIs possible to increase the number of decimal places in tolerances, without changing the global setup of the dimensions?I need three digit decimals for tolerance and just two for general dimension, but is currently impossible to set it as per default in different value. Is just possible to modify it in the drawing, but I need this as global setup. It would be great to change the decimal places as default for tolerance and for dimension separately. 2. Are you using a workaround?Modify manually the tolerance dimension. Always, but sometimes the drafter forgot this.3. What is the use case for your organization?Manufacturing and quality control4. What impact does this problem currently have on your organization?When the control quality manager have to check the mechanical piece with tolerances, have to take the book to check the complete value of the tolerance because the default is just two decimal place, but often the tolerances is composed by three decim
1. Describe the Problem For all situations the user edits a Creo material or material assignment we run a custom logic via "Creo Parametric Object TOOLKIT Java Free API". Hence there is no way to get the information from Creo when the user selects "Cancel" in the respective Creo dialogs and does not chance the materials at all. In this case we don't want to start any actions via "Creo Parametric Object TOOLKIT Java Free API". Therefore we need a way to get the user selection (OK, cancel) of the commands ProCmdMmEditMaterial and ProCmdMmEditMaterials ideally in "Creo Parametric Object TOOLKIT Java Free API" (JLink).This problem had also been reported in C17514420 with the result: "There is no supported API to do that".With this Idea I'd like to ask for implementing new functionality in "Creo Parametric Object TOOLKIT Java Free API" (best case .. or Toolkit if this is not possible). 2. Are you using a workaround?The workaround is to parse th
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.