Recently active
We've received part/assembly files from someone that have restricted parameters. They are restricted to a predefined list of text values. We'd like to change the parameter to something not on the predefined list. I've found that to do so we could build a new restricted parameter list definition, set the proper config.pro value to call for that file, and then invoke the conflict resolution to make the new value available as a selection. The question I have is can I completely remove the restrictions? This seems to be a terrible "well, now you're stuck with this forever" situation. I don't want to have these restrictions inflicted on any new files I create, so I'll have to temporarily set the list-invoking config.pro value only when I want to edit new files from the same source. I'll also have to be careful to close Creo and restart without the restricted list being used whenever I create new files. So in short, can I remove a restricted parameter list from a file that contains one, or i
Hi all, may i know how the BOM is generated in with collecting all the related part by referring the part number mentioned in the property of Schematic file designations
Hi All, Every time I open CREO the option " Enable preselection highlighlighting" is turned off. I ticked it on and then tried to save the config file. still the next time I restart the CREO the option is unticked by default. Is there any solution to it? I would appreciate your help. Thanks so much in advance.
The problem is the following: at some point, the edges of the parts in assembly become invisible in the view; only the hatching that belongs to them is visible. The section in the view is offset type, created by the sketch. These edges become visible only with ticked view setting "Model edge visibility" - "Area", but not visible with "Total" (but should be!).If I create a new view and assign the same offset section, the view is correct. But I would like to use old view, becouse it have assigned boms and hatching properties. What I tried to fix this:1. Updating view/sheet - it didn’t help2. tried to change the section sketch references - it didn’t help3. tried excluding and then including parts from the list of cut parts - it didn’t help4. tried to hide, then show all layers of the view - it didn’t help5. tried to assign a display style for all edges by default - did not help. the similar question not help
I'm trying to turn this hole into a slot. I tried placing a palette over the hole but it doesnt snap. Is there a way to make it snap over perfectly? or do I have to line them up manually? Using Creo 10.
How to show datum axis in drawing views. I have axis in part I want to show in the drawing views. how to show the axis by C# using VB Api.please Share if there is Any Idea.
Hello, For parts or subassemblies that have been suppressed via Pro/Program is there any way to resume these parts or features without modifying the code to un-suppress these items via Pro/Program? If you go to Model-Operations-Resume this screen is greyed out since the parts have been suppressed via Pro/Program. I have some assemblies that I would like to "Save a Copy" to use. I would like for all of the parts to come along, but suppressed items do not come along with the "Save a Copy" option. So I am looking for a quick brute force way to un-suppress all without having to go into the Program to manually do it. Another point, is some users do not have DesignAdvP license so I would like for them to be able to un-suppress all without having the ability to open the Pro/Program code. I am on Creo 9 Thanks!
Hello Everyone, I am facing a problem with 'Dimension Cleanup' in drawing using the VB API.I am fetching dimensions from the 3D Model and placing them in the drawing using the VB API. However, these dimensions are placed in random positions on the drawing, so I need to clean them up and move them to the correct positions for the particular view.Please share if you have any ideas.
HiIs there any possible way to delete or move this option "Expand All" from this model tree menu?I constantly work with very large assemblys, and it happens a lot, when i want to collapse all features, i miss the button and end clicking on "Expand All"This results on long waits, sometimes 5 minutes or more before i can continue workingThanks!
I am using Creo Parametric Release 4.0 and DatecodeM150When modeling features with very high aspect ratios, there is an issue where the thin remaining parts of the geometry disappear when removing material using the extrude cut function.
Dear community. I have an issue with a high of energy comsumption by SYSTEM proces after CREO is running.After the CREO is not in use, the SYSTEM proces works properly. Does any one meet similar issue?Any solution? I'm using CREO 7 + Wind chill on Win10. Thanks in advance.
Downloading the Creo 10 and doing the installation process with everything downloading with a warning. Then trying to open Creo Parametric 10.0.0.0 the traceback file says there is a crash. How do you fix this issue? I am using parallels pro on a mac pro. I have installed visual C++ and Jarva 11 to sort out some other problems I was having. Thank you in advanced.
How to export a creo model to JT (enable xtbrep) with Creo OTK Java / Jlink。 I use such code:GeometryFlags geometryFlags = pfcExport.GeometryFlags_Create();geometryFlags.SetAsQuilts(false);geometryFlags.SetAsWireframe(false);geometryFlags.SetAsSolids(true);geometryFlags.SetAsSurfaces(true);AssemblyConfiguration asmCfg = AssemblyConfiguration.EXPORT_ASM_SINGLE_FILE;JT3DExportInstructions expJtIns= pfcExport.JT3DExportInstructions_Create(asmCfg,geometryFlags);model.Export(jtFilePath,expJtIns); recieive error :XInvalidInput
Hi,I'm using IFX to create my own custom library.I've added a few hardware components. Everything is operating OK, but when I use IFX, I do not get the accurate representation of Screw in 2D and 3D previews.Images are included here.Please let me know if anyone knows how to fix this.I did not find anything related to apperances settings in help section.With custom lib - With Default Library
Hi folks,here the little simplified assembly in creo 8.0.9. I tried to simulate with Simulate the effect over a stator of a clamp.The program gives to me always the error "Creo Simulate could not generate elements for all of theentities in the model"I've just tried to mesh the single parts and it works. The problem is only in the assembly with the part of the stator. I tried also: without the symmetry with different fixing fixing all the dof for better numerical stability without contact interface I don't know where I'm going wrong.
Hello, everyone. More than a question, this is an open topic: Does somebody know a reason why the piping application has not been updated in all these years since Pro/E became Creo? There has not been any change in the way to do piping. I know, some people use to do by swipes and extrudes, others use piping app, and others do spec. driven. But in general, we have had enhancements for manufacturing, electrification, sheet metal, ... And what about piping? Anything? Competitors are WAY FASTER AND SIMPLIER to design routed systems than Creo (for piping/tubing). Will this post be seen by PTC people someday? Let's discuss in the comments.
Hello, I on Creo Parametric 8.0.9.0 Is there a maximum amount of columns in a hole table of datum points? I would like to add over 23 columns to the hole table of datum points.I added a bunch of parameters to the datum point feature. These parameters should show up in a table on the drawing. A hole table of datum points is used. And an export of this hole table is needed as input for another application. While doing this, only 23 parameters, including the standard the standard 'Feature Name', 'X', 'Y', 'Z' can be included. When adding more parameters, to show up as column, Creo crashes. A fatal error is encountered. So I was wondering if there is a max to the number of parameters to be added? Thanks for any reply, Johnny G
int* ids = nullptr; ProArrayAlloc(1, sizeof(int*), 1, (ProArray*)&ids); ProArraySizeSet((ProArray*)&ids, 1); ids[0] = 40; int wHandle; if (ProWindowCurrentGet(&wHandle) == ProError::PRO_TK_NO_ERROR) { ProMdl handle; if (ProWindowMdlGet(wHandle, &handle) == ProError::PRO_TK_NO_ERROR && handle != 0) { ProMdl prdMdl; ProMdlLoad((wchar_t*)L"prtpath", PRO_MDL_UNUSED, PRO_B_FALSE, &prdMdl); //the function can't work on asm->prt //asm->prt is work ProAssemblyAutointerchange(ProMdlToAssembly(handle), ids, prdMdl); } } ProArrayFree((ProArray*)&ids);
Hello community members, This is my first post on this forum. So i hope this place is somewhat active.I have an issue where my assembly is loaded many meters away from the origin.I can fix my issue by moving the parts within the assembly to the origin.But then a more annoying problem arrises.Now my origin is correct when loading in the model. But when I go to create a view in my 2D drafting environment, my origin is now still at the original location.And my view becomes hard to allign to other views. So my question is: When and how is the model origin decided? And can I change this within an existing model that is saved in a database?
I am using Creo Parametric Release 4.0 and DatecodeM150We currently face a challenge in opening “.lay files”.Is that part missing in “PROE_DesignEssG”Here are the errors that I faced"this funcion requieres one of the following:NOTEBOOK
I am new to creo and the creo family of products. When I create a cdi from the pvz and attempt to save the illustration, create a mp4, etc., I get the manifest is missing error. I am working on a pvz on my desktop outside of plm to experiment with animations as my company is working towards adding animations to for our service techs. I found an older topic about deleting the cache to fix this error by going to %APPDATA%\pts\illustrate, but I cannot find this location in CREO 10. It has become frustrating as I put work into these animations and I basically am losing all my work. Thanks in advance.
i want to relate symbol with view by using C# and VB api. any one know solution give me a help.
CREO 10 CAN YOU COMPLETE A SWEPT BLEND (OR ANOTHER WAY IF THIS IS NOT THE CORRECT FEATURE) FROM A PLANER SKETCH TO A CURVED SKETCH, OR PROJECTED SKETCH ON A CURVED SURFACE? HIGHLIGHTED IS THE PROJECTED SKETCH ON THE LARGE BODY, THE CURSER (SMALL RED LINE) IS THE OUTSIDE SKETCH OF THE DUCT. FOR THE DUCT, I MADE THE BODY WITH A SWEPT BLEND. HOWEVER, I NEED TO ADD AN OUTSIDE THICKNESS LAYER WHICH WILL STOP AND CONFORM TO THE OUTTER SURFACE PROFILE OF THE LARGE BODY. SO BASICALLY, I NEED TO CREATE A LOCATION STOP/SUPPORT FOR THE DUCT (THIS IS REASON I NEED TO ADD EXTERIOR THICKNESS TO THE DUCT), THIS WILL ALLOW ME TO PRINT THIS SEPERATE (IN A DIFFERENT COLOR) AND ASSEMBLE IT TO THE LARGE BODY. IT IS CRUCIAL FOR ITS LOCATION AFTER ASSEMBLY. I CANNOT PERFORM ANOTHER SWEPT BLEND FOR THE EXTERIOR TO CREATE THE THICKNESS BECAUSE THE SWEEP WILL NOT STOP AT THE CURVED SURFACE. WHAT ELSE CAN I TRY?? ANY HELP IS APPRECIATED.
Hello, I'm trying to upgrade to Creo 10. I received my license text files through email. I went to the software download page and got the latest version of Creo 10 (Version: 10-0-4-0) and downloaded the .zip file. The problem I'm having is that the setup.exe file does not seem to work. When I double click or right click>run as administrator nothing ever happens and no installation window ever opens. However, when I go into Windows Task Manager I see a process called "PTC Installation Assistant" which is running. If I don't end that process I get an error when trying to re-run the setup.exe file which states "Please exit the already running installer or uninstaller first." I was able to successfully run the "install_license_server.exe" and it recognized the license lm___.txt file and installed the license server successfully. That does not seem to help getting the setup.exe file to work. I'm running Windows 10 Enterprise. I've seen a few possible solutions on this foru
For reasons of convenience I would like to have a closed surface where one of the edges is open in Creo Parametric. A simple example could be a surface of revolution that is swept 360 degrees but has a open edge where the surfaces meet. Below is a artificially created image, where the sweep angle is close to but not exactly 360 degrees. Revolved surface with open edge (but not quite closed) So i am wondering is there: A way to split a self enclosed surface at one and only one edge?A way to merge only said edge and not all edges?Convert inner edge to outer edge?This would be handy at times.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.