Recently active
First of all, this is my first MDO project. It is all relatively new for me.I want to get axial reaction forces in a frame of a cylinder housing in order to simulate vibrations.I used 4 pin constraints and created measures on them. They work fine in radial directions, but not in axial direction. Only 1 constraint reacts, no matter what loads I apply.I tried both with a constant force on the piston as a torque motor on the drive-shaft. Most of you Creo guru's will recognize the model.. Which mechanism constrain do I need to get all the reaction forces? The shaft makes 1 revolution in 0.06 sec. Model attached (engine.asm)
So I wrote a java program to read some tables. However now I want it tomodify the tables to add text and parameters to specific tables using afunction like in the manual. like this: writeTextInCell (theTable, 5, 2, "REV"); (for text writeTextInCell (theTable, 5, 3, "&asm.mbr.PROI_REVISION"); (forthe parameter)In the end, I run the script, a window pops up expecting me to click on atable, I click on the table, two extra columns are added and the bottomcolumn is merged. However I get no text.Anyone knows how to add text to a cell??thanksregardsAlfonsoHere are the important parts on this complete breakfast: currentModel = (Model2D) model; tables = currentModel.ListTables(); TableCell cell1,cell2; Table theTable = null; String cellName; SelectionOptions selops=null; Selections sel = null; selops = pfcSelect.SelectionOptions_Create("dwg_table"); selops.SetMaxNumSels(new Integer(1)); sel = session.Select(selops,null); sel.get(0).UnHighlight(); theTable = (Table)sel.get(0).GetSelItem(); w
I am using Creo Parametric Release 9.0 and Datecode9.0.2.0First I should point out that I have been using Creo since early ProE. I have generated thousands (literally) of drawings.I have a plate with some holes, some tapped and some not. I am not able to show the threads on the tapped holes.
Hello; I need to create dxf files from SolidWorks, & pull them into Creo for a cgm file output. One problem I had was the dim arrows are filled in SW & also in the dxf file, but when I import them into Creo they're not filled, thus not in the exported cgm either. The section line arrows remained filled, but all the dim line arrows were not filled. I posted a question in this gentlemen's YouTube post because the dim arrows are showed not filled in it as well. https://www.youtube.com/watch?v=33ZFv_szMAU&t=334s Thanks in advance for any input.Rob_D Creo 4.0 M060
Has anyone had luck with table.settext? For me it's breaking and a try/catch isn't throwing the error message. The table is generating up to this point.I know it's breaking because if I moved the mergeregion after the settext, that doesn't work, and the rest of my code isn't running either.Any help would be appreciated! Thanks! var dwgTable = drawing.CreateTable (tabinstrs); var topLeft = pfcCreate ("pfcTableCell").Create (1, 1); var bottomRight = pfcCreate ("pfcTableCell").Create (1, 5); dwgTable.MergeRegion (topLeft, bottomRight, null); try { dwgTable.SetText(1, 1 , "CONN NAME PART NUMBER"); } catch (err) { alert("Error setting text in table cell"); }
Dear PTC Community,I am currently trying to obtain a selected driving dimension from the selection buffer in my Creo session. My current approach is to start by getting the current selection buffer: pfcSession_ptr _session = pfcGetProESession(); pfcSelectionBuffer_ptr selBuffer = _session->GetCurrentSelectionBuffer(); Then, I list and iterate over the selected items and filter out all selected annotation elements: pfcSelections_ptr currentSelections = selBuffer->GetContents(); size_t sizeSelection = currentSelections->getarraysize(); for (xint i = 0; i < sizeSelection; i++) { pfcSelection_ptr selection = currentSelections->get(i); pfcModelItem_ptr item = selection->GetSelItem(); if (item->GetType() == pfcITEM_ANNOTATION_ELEM) { wfcAnnotationElement_ptr anno = wfcAnnotationElement::cast(item); wfcAnnotationType annoType = anno->GetAnnotationType(); if (annoType == wfcANNOTATION_DIMENSION) { [...] } } } However, in line 10 where I call
I'm trying to change the Text tool in the sketcher so that a certain font and alignment is used every time. I can create a mapkey, but if I continue to make a second text item the settings go back to the default. Is there a way to change this? I didn't see any options in the config editor.
Is it possible to import drawing page creo into a new drawing Creo Parametric but with associativity ?With the functionnalitie import drawing/data is possible to insert a specific page in my new drawing buth without linkMaybe option or specific application?Thank you
Hi,I have a drawing with a model that has a inherited model (not sure if that matters).I am trying to change the crosshatching but in Layout tab, the crosshatching is unable to be selected.I also changed the crosshatching on the cross-section in the model, but it does not update on the drawing. Is there any other way to change crosshatching when it is unselectable on the drawing?
Hi Everyone, I want to create illustrations in creo illustrate in some other language. Can someone guide me how to go about it . I am using Creo Illustrate 10.1 Thanks in advance. Regards,Aditya Gupta
Prior to CREO 6, I can install a new release of CREO on my machine and create a 7zip archive. Users can extract this archive and install this on their machine without using the software center or requiring local admin rights. With the new releases now, you have to run the creoagent (creosvcs_64.exe) which requires admin rights. PTC support stated that this is not a supported method, and not offering any workarounds. I believe some folks are still using this method for their deployment. Just curious how I can do this for our CREO 10 deployment and not have to rely on the software center. Thank you all in advance! Calvin
I am running Creo 10. I have both Creo Live Simulation (powered by Ansys) and Creo Ansys Simulation. I noticed that under setup in Creo Live simulation, I am able to select "Scope". However, when I look for this option in Creo Ansys Simulation, I don't see it. It'd be convenient to be able to exclude unnecessary components, but still be able to run a more robust Ansys simulation. Is this option available somewhere that I'm not noticing?
Hello,I have to display a BOM table on the drawing.Default the table will display POS number and Quantity of the item e.g.: POS 20 Qty 2 (each)In this case I have added a tape to the ASSY, which is also displayed in the model and it will beadded in the assembling stage from roll.Is it possible to change the BOM table to e.g.: POS 20 Qty 2 cm ?I can create a bulk item, but that is not visible in the model and the drawing.An other way is to create a part which displays 2 cm tape, but in that case I have created a separate item, which more or less produced before the assembling action.Any idea how to implement this?
I am using Creo Parametric Release 8.0 and Datecode8.0.4.0Hello,I would like to create a PDF which contains a drawing in format 8-1/2 by 11 (A) and a format 11 by 17 (B), in the same drawing.example: page 1 is of format A and page 2 is of format B.Except that, when printing if the format A page is first, the second page which is format B will be compressed into format A.So, is it possible to create a PDF document and have the first page come out in format A and the second page come out in format B.
Hi Guys,Can we use the "Excel Analysis" to get a parameter value into excel if I change it in excel it'll update in the 3D model. it's possible Regards,AJ
here is an example
Is there a way to save a view in a drawing as a combination state in the model without manually creating it in the model?
I'm running Creo 10 with a Creo Ansys Simulation add-in / license. I have a fairly simple setup with two circular plates touching each other. I've intentionally omitted screens of the parts for proprietary purposes, but the feature tree is below. For some reason, when I try to generate a mesh using a Free contact, it fails. But if I change it to a Frictionless contact, then generate the mesh, then switch back to a Free contact, then re-generate the mesh, it works... I'm not sure if this is a glitch or if I'm just missing something... Below shows the steps of how I'm able to turn on and off the issue: 1) Contact is Free initially, Generate mesh > Mesh Fails2) Change contact to Frictionless, Re-generate mesh > Mesh Succeeds3) Change contact back to Free, Re-generate mesh > Mesh Succeeds4) Change mesh size to low5) Steps 1 thru 3 occur again6) Change mesh size to medium7) Steps 1 thru 3 occur again
Hello, I've a part with an intance (BRUT), and in the same drawing, I want two sheets. One with the final part, this other with intace.The weight of my part and this intance are different. But in my drawing I can't manage the different. Do you have a solution to manage it? Best regard,Luc
Hello,If possible get "COMPONENT INTERFACE" information from a 3D model?I get the feature by use FeatureType.FEATTYPE_COMP_INTERFACE);and find this feature is implement the interface "WFeature".But I don`t find the the class for this "COMPONENT INTERFACE" feature .Would you know how to get these information?
Is it possible to move the Assmb.drw to assmb1.drw sheet directly.
Hi there, My company updated to Creo 8.0.1.0 some weeks ago. Now it turns out, that the model check test "DEF_DENSITY" does not work anymore in Creo 8. In Creo 8 every part gets the default material "PTC_SYSTEM_MTRL_PROPS", which has the density of 1.0. The test DEF_DENSITY should check, if the density is 1.0, but the test passes. Since we use modelcheck as a gatekeeper for our windchill, there is a pretty chance, that the pdm-system gets filled up with neutron-star-like parts. Does someone knows a workaround?
Hello, I'm working in Creo Parametric 9.0.7.0. I have a model of a box with a door on it. I have two versions of the hinge for the door, one open and one closed (the only difference is an angle constraint that switches between 0 degrees and 180 degrees). I created an interchange assembly that maps all the pertinent geometry on one hinge to the other. I can replace these hinges and update my model and the door will open/close fine. I would like to have a simplified rep to be able to swap between open/closed configurations, but Creo doesn't seem to allow that unless I use a simplify interchange assembly rather than a functional interchange assembly. My problem is that the simplify assembly only does a cosmetic update rather than a functional update (it doesn't update the constraints). Is there any way to set up a simplified rep to switch between parts of an interchange assembly and have the constraints update in a top level assembly? Thanks,Matt
(I assume) many of us make tabs on sheet metal parts. it would be nice to be able to set the width of a tab, rather than rely on doing the math to set it's offsets from each side. To give the option to have a full length flat / flange, or to set its width & offset from an edge.. i.e.: I want a 3/4" tab, 2" from one edge of my part. I have to do math to figure out what I need to offset from each side is to get this.. But, if my part changes width, the tab width then also changes by that amount..
Hello, I'm looking into UDF's and the possibility to use them to create variable assemblies and place these into a main assembly. I would like to make 3 UDF to help me easier create a casing.1. A steel frame UDF where I can have some standard component corners and then some variable profile lengths. 2. A panel UDF where I can change the length and width of the panel and have the components inside change dimensions accordingly. 3. A door UDF where I also change the outside dimensions, but have some standard components, like a door handle. The idea is that I can create casing by first take a frame UDF, designate the size and place it in an assembly, then take panel UDF's one at a time, designate sizes and mate them into the assembly. And if needed, choose a door UDF, designate size, and then place it in the assembly. I have worked a bit with the UDF function and I have access to the AdvAssem option in Creo 9, but I haven't had success in making t
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.