Recently active
So far, there is no Toolkit function to update the restriction definition of parameters.There is only a workaround by using macros (see also PTC article CS235369).However, the use of macros is not version safe: A macro that works in Creo 7.0 may not work in Creo 8.0.Therefore, I would like to have a corresponding Toolkit function!
Until Creo 4.0 we were using the Attribute PTC_MATERIAL_DESCRIPTION instead of PTC_MATERIAL because for the latter you only get capital letters, the "description" can be according to (ISO) standards and include lower case. Starting with Creo 7 there is multibody now with the possibility to define more than one material per Part. If one wants to designate only the material assigned to the model, and none of the materials assigned to bodies to the drawing frame one has to use the Attribute "PTC_MASTER_MATERIAL" which only includes Capital letters. To work according to standards, lower case letters are needed. This is why the Attribute "PTC_MASTER_MATERIAL_DESCRIPTION" is needed.
In sketch mode, it should be possible to convert arcs to circles.
The PSF is useful for setting environment variables that are read in no matter where parametric.exe is called from (like windchill), but when you change license configurations the file is overwritten and your changes are lost, and the changes have to exist in every different PSF that is used. Instead of all that, add a separate config file (xml, perhaps?) that will be read in by parametric.exe, no matter which PSF is used. For full implementation, allow the user to specify a config file other than the default in the command line. Basically, it's just a second PSF being read in, but it is independent of PSF selection and does not get overwritten by a reconfiguration.
It could be very useful in order to dialog with Autodesk world
Hello, When working on large assemblies, when assembling small components (likes screws). Sometimes the drag handle is located far from the part itsef, and this 3d handle is not dependant on the zoom, so the placement becomes difficult ... Same thing can be noticed with cross sections 3D translation handle , its also not dependent on the zoom, sometimes difficult to use in large assemblies.. Can you create a setting that allows the 3D handles dependent on the zoom?? Thanks in advance
Sometimes, user, presses the regeneration button, but it should be possible to stop it. When we have a heavy project, regeneration times can be long. And if by mistake the user presses the regeneration icon, it will take a while to make the complete regeneration of the project! So make the stop button work while regenerating.
When using a 4K display the font size of windchill is quit small, you can adjust this manually , but it's not a saveable setting. We'd like to set the font size for this in creo settings or in a subpage of the browser.
Hi,did any of you has an experience with the following topic ?i searched the knowledge base and found only reference to old documentation.Many thanks,
I am using Creo Schematics Release 8.0 and Datecode8.0.0.0 how to add splices for more than 3 wires in Creo schematics.
Is there any way to make the operations of cosmetic lines for explode views result in a standard way? Is there anything being done to make what should be a simple feature work correctly?Why do I not trust any community member when there are things like this being provided as solutions?https://community.ptc.com/t5/3D-Part-Assembly-Design/Explode-Line-Issue/m-p/390043#M6732 It is frustrating to see that the issue I have in 2025 had been addressed in 2015, and the 'solution' to the issue was a link to a poll to try to convince PTC to care? There is ZERO options to apply to make the cosmetic line for explosion views result in any sort of expected way. I have attached a simple look at what can be the result of adding a cosmetic line 4 times in the same way. The result should be 4 identical lines. It is not. This is a simple core feature used in all of CAD work.
All, Have you experienced the event manager not showing information regarding failed events? This is happening randomly and is starting to occur a few times a week. Creo Parametric 5050 Windchill 11.0 M030 CPS14 PTC only has a workaround which is to rename the event folder in their cache and restart Creo, then try previously failed process. The workaround works but we need to understand why this is happening and if this is fixed in a newer build.
I know this is a future question but perhaps a PTC PLM can chime in. I see that Cadence released version 24.1 last year. I was curious if Creo View Adapters 12 will support this version. The 11.1 version only supports up to 23.1.
Hello All, Hope all is well; I need to know how to calculate the Rope wires core and strands wires dia the outer dia is .0195" I have attached the picture for references. With Best Regards, Adnan
Hello Team, I am facing drawing layer issue in my drawing. i have hidden all the layers and isolate drawing display layers but when i try to save status, doesn't allow me and asking to check out the loverlevel assembly which is released. the lower-level components are released, and layers are not hidden for axis.can we control those layers in Creo drawing layers?
Hi What parameter in config.pro specifies the template folder path for Creo Simulate?Default Result Windows Templates Thank you all in advance.
Tried to research this and found other posts but no results listed. Using CREO Parametric 10.0.4.0In an assembly, I have 10+ components assembled and always try to fully define the constraints. As I am adding additional components and constraints towards the end of the design (hardware) I start getting "Confirm Package Reference" which to me indicates another assembly component is not fully defined. I can click "Use Ref" and move on but want to resolve the unconstrained component that I am assembling new parts to. Looking back at the assembly tree, I see component #10 has a small box indicating it is not fully constrained. I click to edit constraints, and the Set Status says "partially constrained". Yet I have three constraints (coincident/distance/distance) that should fully constrain the part/subassembly. So I uncheck "Set Enabled" and create a new set. Using similar constraints, I get the status to read "Fully Constrained". Close out th
I am using Creo Parametric Release 4.0 and DatecodeM0701. User set correct config.pro file and chose the correct font path2. User config correct in drawing properties and set the font type3. then reopen the drawing propertiers setting, it rollback to default setting.Could you assist me to investigate it? user`s font couldln`t be set correctly
Hi all, my cosmetic threads in my drawings are displaying through the part on a section view.How can I get it to where the vertical lines are not showing?
Hey guys, i am using PTC Creo Parametric 7.0 (Student Edition) I created a thread on a pin. Unfortunately, it does not really show the outlines (actually the inner lines) of the thread: My visibility option is on "only show visible edges / lines"If I select "show also not visible edges / lines", creo will show the whole thread but also everything else, which is not good for me. Can somebody help me with this problem? Greetings, Spedex
Hi Every one,I am new to Creosim.I am trying to simplify a connection using combination of spring idealisation and contact interface.Two separate parts are assembled with these connections in parallel.When the connection is under compression, we have contact and spring is compressed. When the connection is under tension the contact is released and there is no force for the spring.1. I am not sure if is it possible to have contact between spring end and second part ? Ifound for the contact we need a surface, so do I need to define a surface between spring and second part or it is possible to have contact interface between a point and a body?Because of number of conections I am looking for a quick and easy method. Only I am looking for the force at connection when it is under compression.Any help is appreciated.
Creo 8.0.11 Hi folks, 👇here, my headache... I want to have a fine mesh in a region of this column because I need to insert it into a bigger assembly for a Contact Analysis. I know that "mapped meah" isn't that kind of mesh control that is passed to higher assembly level, but I want to test here to already know how to mesh it in the higher assembly. But I don't know why I can't mesh properly. I also tried to mesh in this manner. It works for the external elements, but I can't be able to make the wedge inside. Do you have any suggestion?
Hi,I've tried to replace the Ground Springs with simple ones in order to can run also a Large Deformation Analysis.It fails...but I don't know why...
When importing emn files directly in Creo Parametric, is it possible to set the default import of emn files to Assembly mode instead of Part mode? According to PTC eSupport article - CS398256, It's not part of Creo Parametric functionality.Now I recommend that PTC improve in future Creo releases.
(Using Creo 8.0.9.0) I'm fairly new to Creo (under 2 years of experience with 5+ yrs of other CAD software experience prior) and I am looking for some advice on best practices for using layers in Creo drawings. I've previously struggled with layers when trying to make some skeletons visible in drawings but not others (similar to how you could hide features in the model tree in an assembly or part). The goal is to have the one particular skeleton visible in the drawing but hidden in the model (while other skeletons are hidden). This is the way it has been done previously at my company with large assemblies that contain multiple skeletons. Most of these situations end with frustration because hiding or showing a layer does not work to hide or show the feature contained within the layer. I realize I could just create a simplified rep for each view, but I would like to figure out layers for consistency with other company files (I'd also like to learn how to use layers in general!
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.