Recently active
I've created a 2D drawing from a 3D model on a C size sheet. Is it possible to change the drawing to an A size sheet and keep all the work I did on the C size sheet?
Hi Agnes,Good. I hope this has been of some help, and you can create the geometry, symmetry constraints, and mapped meshing to meet your criteria.
The product called Solidworks, as folks know it today, has already split into two development streams. Solidworks will stay as it is with the same modeling kernel until and beyond the time when development is halted in the future. For CAD, a modeling kernel is analogous to the engine, drive train, and chassis of a car. Solidworks V6 (now called Solidworks Mechanical/Conceptual and other solutions will be added) will be the new product that will take over Dassault's development efforts and it will be based on Catia's modeling kernel. If they wish to avoid any data disruption, Solidworks users of today will need to continue using today's Solidworks in the future even though there will come a time when there will be little to no further development effort put into the product. Dassault will give incentives to entice existing Solidworks customers to move to Solidworks "V6" (Mechanical/Conceptual) even though there will not be true data compatibilities. Solidworks "V6" will likely have the
Demac,Please look at Page 7 in the attached file. Currently, PTC does not have CFD, and I think there is a Product Idea to add this capability. But there is a product call FloEFD that can be used with Creo.
Are you going to make this a Product Idea?
Jim,I've been using Creo Simulate since it's introduction with 1.0, and prior to that, all the way back to Mechanica and Pro|Mechanica (1999).
Anges,I've attached the model, and I found out that the more brick elements I added, the smaller the % difference between the max and min radial (R) displacement. You don't have to use as many elements that I used in the attached model, and you could use just a 1/4 model, as I was just experimenting (Creo 3.0).
Mark,I recommend the Help Center be updated to reflect Creo Simulate Lite, as shown in the below image, and anywhere else the Lite may need to be inserted. I counted at least seven places where Lite needs to be added.
When you view the animation normal to the holes, does the tip displace perfectly in the Y direction?
You may be able to know the tip displacement in the Y direction by using a pre-defined measure on the edge, but I haven't tried it myself. You can find this by going to Measures.I can make up a wishbone model and run it myself, tomorrow when I get back to the office.What is the material of your model?
Try changing to Absolute Accuracy.
Even Abaqus wasn't perfect, because it didn't show 0%.
Anges,I can post the model tomorrow, because I'm out of the office today.
Creo appears to perform very well when using symmetry and mapped meshing, as I ran both 1/4 and 1/2 models (1/2 model below). But it should produce the same results with 360 and automesh.
These instructions are for Creo Simulate Lite, not Creo Simulate.
This is what happens if you attempt to switch to Creo Simulate Lite after a Creo Simulate model has already been constructed (image attached).
Is the Process Guide for Creo Simulate or Creo Simulate Lite?
Erik,Has PTC come back with an SPR for this problem?
Can you upload an image that shows the words "Process Guide" in the GUI as you stated in the tutorial?
I ran the model in StressCheck, but different pressure and material (closing time here). It appears that I don't have that problem when plotting a 360-degree cone (images attached). I will plot the points in 360 tomorrow. I just don't have time today.
I have StressCheck and ANSYS.
If I recall correctly, there was a Product Idea for this.
With the introduction of Powered by jive, the "view all participants" capability appears to have been removed. It is recommended to restore this capability.
Call PTC Support at 877-275-4782 and listen to the menu and select 5 for License Management.
Student .prt files cannot be opened by Commercial .prt files.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.