Recently active
Hi Stefano,Can you upload an image of the problem or sketch and define what you want excluded? On the other hand, you could create a measure on the region of interest and plot convergence on it and not worry about exclusions.
It's from Dr. Toogood's book as shown in the attached link. He has newer versions now for Creo Simulate.http://www.amazon.com/ENGINEER-Wildfire-Mechanica-Tutorial-Structure/dp/1585033812/ref=la_B00J1WQQC4_1_10/175-7986978-0398902?s=books&ie=UTF8&qid=1440543404&sr=1-10
If you're going to run 2D, make sure your surface is in the positive XY plane, or you will get an error.
Try making a surface region to represent the area where the collar would make contact with the pipe and apply the load on that surface.
The attached 2-page document helps clarify the differences between h-elements and p-elements.
Nice sweep, but the start/stop is on the same plane? Or is it?
Hi Antonius,I just wanted to show that PTC does have 3D curve sketching, but its' for Elements/Direct Modeling. Notice all the capability it has in the ribbon tab for 3D curves.
The attached model image was made with just three curves and no points. The orginal post stated that you had to make the curves through a series of points. Even if you sketch a spline, you don't have to make a curve through previously created points, but I do like the idea of having 3D sketch capability.
PTC does have 3D sketch capability in Elements/Direct Modeling. Watch the attached video.http://learningexchange.ptc.com/tutorial/3493/creating-3d-curves
Are you talking about the attached video?https://m.youtube.com/watch?v=mKFNHX3OlIU
Can you upload an image of the SW sketch?
Steve,DId you resolve the problem? Did you try the model I uploaded? Take the model I uploaded and delete the mirrored group then try to remirror. Try it in a clean directory. M030 should handel a simple mirror task as this. You could make a simple blend to connect the two ends of the rod and not worry about mirroring.
Vaibhav,You will find some useful tips in the attached file from Urs Simmler for roller-bearing constraints. Start on Page 23 and work your way through Page 27. Weighted Links: "Tips & Tricks" starts on Page 19. The whole document is 40 pages.
Steve,The default setting is Dependent Copy in M050 and you should have been able to do this in M030, I mean mirror the features without any problems.
In the transitions, the part thickness varies slightly.
Hi Sudheer,We have an entire Community for Assembly Management, as shown below, and I recommend you post your question there, as you may get a better response. Welcome to the forum.
Steve,I think I would have made Extrude 5 the final cut then make the rounds. Someone made Extrude 5 then Extrude 4 then the rounds associated with Extrude 4, and that's okay, because it still mirrored as a group anyway. FYI.
Steve,I took a look at your model, and I was able to mirror the group without any problems as shown below and I attached the file. I'm using Creo Parametric 3.0 M050. Hope this helps.
I'll take a look at it tomorrow.
Steve,Are you trying to mirror at the part level or the assembly level? I'm currently using Creo 3.0 M050, and I'm not having problems with mirroring (and I didn't have any problems with M030). Can you you upload an image of the problem?
Steve,If you can't mirror the Group, then there is something wrong in the model.
Steve,You should be able to mirror the Group also, as shown below:
David,Yes, you can hide components. Select the Display Location tab and then select Components/Layers. Another window will popup and just blank the components you don't want to see.
Steve,I built a quick example, similar to yours, and I didn't have any problems with mirroring the pocket, as shown below. If your model is not proprietary, can you upload it? I'll take a look at it. There maybe something wrong in your model, I don't know, but this is an easy task for Creo, and you shouldn't have any problems.
Ruben,When you select the part, does the Solidfy icon turn active? If so, then just select Solidfy and convert it to a solid.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.