Recently active
Bjorn,Creo Parametric does not have 3D sketching capability, as much as I hate to admit it. There are several Product Ideas to add this functionality to Creo Parametric like it has in Creo Elements Direct. You can create 3D curves through multiple planes, but it's just not as easy. Here's the Product Idea link:https://www.ptcusercommunity.com/ideas/6187
Add the capability to sketch a midpoint on a spline curve while in SKETCH MODE, and allow the midpoint to update while editing the spline. Also, allow nodes to be positioned at a ratio or length along the spline in SKETCH MODE.
Creo 3.0 Help Center currently uses Internet Explorer to view text and images. Creo 2.0 uses Arbortext. Implement Arbortext for the Creo 3.0 Help Center. We've had consistent problems using IE, and IE is totally blocked from the Administrator account. Arbortext appears to work much quicker than using IE.Creo 2.0 Help Center
You,You can vote on this Product Idea if you so desire:https://www.ptcusercommunity.com/ideas/6350
I closed the session, reopened the file, and the pattern went away.
Anyone get patterns with reflections?
You,It sounds like you want a visual dynamic midpoint as you edit the spline.
Ben,I'm really not getting the gist of the concept of only getting credit for 1 vote per company. If we have 10 end users, and we're paying maintenance for 10 seats, and everyone (all 10 users) want the enhancement, then all 10 votes should be counted as valid by PTC. The same concept should be applied if you had 100 end users. Is that the way PTC really thinks about its customers?
Tom,I really enjoyed your response, because I always hear the excuse from PTC that a particular Product Idea doesn't have enough votes to be considered. So how many votes does it take PTC? And as you pointed out, there is no particular number. One PTC employee told be directly that the Product Idea system is broken, and another PTC employee told me just a few days ago that the Product Managers point their fingers at one another and say, "that's not my area", and the Product Idea doesn't get assigned to anyone, and then it just is shoved into a cyberspace corner and forgotten.
You,You could make the desired spline curve, then locate the midpoint in the spline by making a point on the curve by ratio. I know you want to locate it in sketch mode, but you could locate it with a point not in sketch mode, as shown below.
You,Let me see if I understand you correctly. You want a midpoint between the beginning and ending points of the spline? Correct? Because you have five points in your spline curve.
Frank...it's not a draft.
Thanks for the response and well received.
Mark,Just fill it in with one solid extrusion up to the surface. See below image.
If you vote on a Product Idea, and you discover later that Creo has the capability and doesn't require the Product Idea, how do you remove your vote?
However, there should still be the option to remove your own vote for whatever reason. For example, someone votes on an idea, and later decides that maybe the idea is not so great afterall, perhaps just an impractical idea after some extensive research.
Ryan,Good point. In this particular case, only a couple of days had elapsed. So the bottom line is that there is no way to remove a vote once voted upon. I made the recommendation to the originator to amend the Product Idea to have the functionality added to core Creo for those who don't have ISDX. Or he could just start a new idea.
Antonius,Nice work. Do you think the same could be done with the Style tool with less effort?
I've done this in StressCheck with a hand mesh, where I had created small elements to represent the size of the bonded area. In Creo, you could make little surface regions to represent the bonded areas instead of using points, and this will give you the strain over that particular area, but not average. A strain gage area is so small to begin with. I haven't tried an average over a surface region, and I will look at it tomorrow.
Brad,It's greyed out when you select Analysis for Mass Properties, because I think it is PTC's intent for you to select the CSYS then read the desired density of the entire assembly or at the component level.
Lawrence, I submitted a Product Idea to have a Group for drawings, you can view it in the attached link: . - PTC Community
Dan,Now I would recommend exporting the NX as IGES and Creo as IGES and import the two and see if the points are in the same location.
Dan,There was a slight difference in points when not doing with ISDX. The point on the surface without using ISDX was about 0.007" off from the point created using ISDX. I zoomed in to measure the distance between the two. Zoomed out, you really can't tell the difference. So it's a little off.Figure 1: Two IGES FilesFigure 2: Point Measurement
Dan,I created this point on the surface without ISDX, and I will have to compare it to the one made with ISDX by overlapping the two as IGES files. That will be the proof. I'll do that after lunch.
The functionality is available with ISDX. Here is the link: https://community.ptc.com/t5/Creo-Parametric-Ideas/Point-quot-On-Center-quot-Of-A-Surface/idi-p/471377
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.