Recently active
Paul,See if the attached file will import on your system. It works for me, and it's just a simple angle.
Try importing the .model file from the ribbon Get Data>Import
Can you compare the PC hardware from your previous company to the PC hardware you're using now?
......better yet......what's it for?
bcarlock,Check to see if you have the STEP translator, and use the below example to check your system.
Paul,I have also imported extremely complex .models, for example, the entire pilot and co-pilot seats with all the framing, belts, hardware, cushions, etc. Very complex with no problems at all.
With the Reflection Analysis option, you can simulate the reflection of light on shiny or glossy surfaces. Surface imperfections, such as curvature discontinuities, become obvious when rotating the model and viewing the reflection curves. Breaks or interruptions in a reflection indicate a surface discontinuity.
It would be nice if you could share a file that's not proprietary, and then I could test it here. But I've imported 100s of .model files, and I've never had one fail.
No, because I'm running Creo 3, and that response was for Creo 2. Here are the option modules I'm running:
I haven't had any problems IMPORTING .model extensions with Creo 3.
Are you using Creo 3?
Is there a way to open a ".model" file in Creo Parametric 2.0? A ".model" file is a CATIA native file, and I can open them up in CATIA, but not Creo.
Community,When I select Perspective View after selecting Shading with Reflections, Creo uses a default background picture, as shown below. I went into Perspective Settings, and I didn't see a way to disable the background picture. I want the Perspective View with Rendering without the picture. Is there a way to do this?
Charles,I went to SAXSIM, and I couldn't locate Jakel's presentations. Do you know the full URL path? Thanks.
Charles,I'm extremely interested in what PTC has to say about this, if they even come back with a response. I would love to see an explaination from their developers as to why Creo will not perform the analysis as well as ANSYS.
Good point Herbert. I research the functionality before I submit a Product Idea by presenting it before PTC support. In other words, I'll contact PTC support when I'm attempting to do something in a PTC product, and when PTC replies that it can't be done and I see where other software like CATIA and NX can, then I submit the Product Idea. I've only submitted a few Product Ideas to enhance community help, etc. But most of them are for Creo Products, especially Parametric and Simulate, and none of them have even been considered for future development. The main reason I posted this question in the first place is that a PTC employee told me that one of my Product Ideas wasn't getting enough votes, so then, I replied, okay, "How many votes does it take?" If PTC is going to say you need "x" number of votes, then okay, how many? But you see, it appears they, PTC, are not going to commit to "x" number of votes, of course, assuming the Product Idea is a
This is the product to perform CFD with Creo.https://www.ptcusercommunity.com/docs/DOC-5303
Denis,I've seen all kinds of tube fabrication in industry, but I haven't seen this type (in your image). Do you have an actual picture of the metal tube after fabrication?
When you go to your own profile and look at the Product Ideas that you submitted, it doesn't add the total number of ideas at the bottom or top of the web page. Add the capability to the web site to allow total summation of Product Ideas that the end user submitted.
Mats,That's okay. I was wondering if Charles presented his results to PTC support, since ANSYS seemed to work better than Creo (the problem with a smaller block on top of a larger block) and working with friction.
Richard,Yes, Creo can do this easily, as shown below. Select a Plane that you want to intersect. Select Section>Planar. Drag the arrow back-and-forth to see a dynamic cross-section.
Patrick,I know about the p-element version vs h-element, as I was just wanting to hear what Mats thinks about this since it was his post about ANSYS and the smaller elements vs Creo. I've attached a document from PTC on the contact theory used in WF4, and a lot of this is still in Creo.
Colin,I made a quick example of your idea, and I used the swept blend function, as shown below. If you'll upload your curves, I will see if I can make it for you.
Charles,Were the results from your Creo and ANSYS studies presented to Creo Technical Support?
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.