Recently active
If it means anything to you, I would go with the Dell 7710. I'm ordering mine this week. I toured Lenovo headquarters in Morrisville, NC, this past spring while attending the Pro Users of the Carolinas event. We got to tour the R&D department and talked with some of the reps. They broke down, actually took apart their current desktops and the workstation laptop. I just wasn't too impressed after looking at the Thinkpad, but I know that looks can be deceiving. Performance is what counts. During the Creo challenge, I used a Thinkpad with Windows 10, and my partner and I couldn't make the UDF for the competition, not for lack of talent, but it wouldn't work with that operating system on that particular laptop.
I changed the Product Idea title and added Parametric.
Is there any reason why the curve through datum points won't give you the same results?
Can you upload the point file?
Hard to tell with just a picture. The color of the geometry edges appear to be black, and then you have all these blue curves. The blue curves can probably be hidden if you don't like the appearance. If nodes are created at the ends of the blue curves, then you may have to modify the model to get rid of these. Can you share the model?
Thanks Stephen. I kept looking for it in the Creo pull-down and never located it.
Where did you add it?
Excellent.
You might find some useful information in this thread (but not Creo info):http://www.rcgroups.com/forums/showthread.php?t=1459421
Mark,Shouldn't the elevator be a separate component, and yet the contours of the elevator match the wing (horizontal stabilizer)? Are you stating you don't know where along the stabilizer to place the elevator rather than how to create the elevator?Welcome to the forum.
Naveen,Yesterday, I opened up your model and realized that you're talking about an assembly. When I first responded, I was just thinking of a straight simple hollow pipe. So I took your assembly and just copied half of the inside surfaces, then I used the edges of those surfaces to make a 360° solid to measure the volume. I posted an image of it yesterday. This was the most simplistic solution I could think of at the time.
I just copied the internal surfaces and then revolved a 360 solid. I got the same volume as Tom.
You can Copy/Paste the inner surfaces, and then you will have to use the Fill command to cap off the ends. Then Merge and Solidify. You will then have a solid volume that fills the pipe.
Measure the volume of the hollow pipe. Call it V2.Fill the pipe with a solid sweep and measure the volume of the solid pipe. Call it V1.Subtract the volume of the hollow pipe from the solid pipe. V1 - V2 = V3Or you could just measure the volume of the sweeping solid that was used to fill the pipe.
Gorka,Are you stating that you don't want discontinuous lines at the intersections circled below?
How does your graph look?
Gene,Your file was created in an educational version of Creo and cannot be opened with a commercial version of Creo. The path to shear-moment graphs is shown below.
Making a plethora of offset lines in an assembly can lead to long model trees. Creo Parametric 3.0 does NOT have the capability to group offset lines, so the model tree can be contracted. Add the capability to group offset lines.
I can see why you were having problems filling this in. I haven't finished yet, but here's an image of the blend on one side, other side is similar. You have geometry that really isn't suited to a boundary blend then thicken. So another approached would be to fill all the boundaries with surfaces, merge them, then solidify. But that's just one way. You could also, I think, fill this in with a sweep with trajectories.
If you have the Advanced Fastener Tool, you can calculate the shear, axial, and bending stresses in the bolt through two components.
Do you have the Advanced Fastener Tool in Simulate?
ReplyUse advanced editorAttach
Can you upload the model?
You can fill this in with the Boundary Blend tool (two directions) using a surface, then Thicken the surface to the desired thickness. Select the outside edges of the geometry for the blends.Then test the geometry for meshing.Welcome to the forum.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.