Recently active
Please refer imgaeI am always getting struck whenever i need to create a curve profile like the image attached Please help me out & request you to create a 3d model and share , it would be betterAnd teach me the techniques that how to craete this kind of profile in future
I just recently downloaded the student version of Creo Parametric 2.0. But when I open a model the welcome tab stays active and I can't see my model. If I click the close button on the welcome tab the tab just freezes. What do I need to get the welcome tab to close?
Any experiences? Compared to Windchill 10?
Hi, Is there any easier way to make slots rather than joining two circles with two tangent linesRegardssamuel
Greetings,Anyone have validation data on upgrading from Pre-E/Wildfire to Creo?We are looking for evidence that the SW upgrade does not change the CAD data.
I need to creat this image. I know I am probably making it harder then it is. I can get everything but the 80 radius. I'm not sure how to have both the 40 and the 80. I've tried a variety of things and still cannot get it. Thanks
Can anyone help me how to do solid geomentry mirror in Creo-2?? where in wildfire-5 i had this option for solid geomentry mirror.
Posted this a few days ago and not sure as to whether or not it went through, so trying one more time. This also piggy backs a little on the "should scale be removed" thread.
In my case I have assigned pin for the shaft & later defined force motor for the same. But If i run the analysis the shaft is rotating clock & anti clockwise .How to control, only it should run clockwise direction ?
Can someone tell me how to rename a column in Creo? it's been 4 years since I've worked with Pro.Thanks,Will
HI alldoes anyone have a post for a haas vf3 thanks mick
Is there a way to have a 'Copyright Protected' notice pop up whenever an IGS file (or a STP file) is opened?I have a need to send an IGS file to an external organisation with which we have a NDA in place, but they may need reminding (preferably each time they open it) that the data is ours, not theirs.I think I probably know the answer...If I'm correct, how have you folks dealt with this problem?Cheers,John
Hello group,We have a couple users starting to get errors when opening up files. It started with opening numerous files and then eventually when opening another large file we get an error:
Dear all,I am trying to call a mapkey, that I have already defined in CREO, from excel's VBA.Is this possible ?I would would be thankful for the help Regards, Nicolas
I have an IGES model from a supplier for a piece of equipment that will be used on a tractor. The model imported as a set of surfaces so the model mass and center of gravity are currently incorrect. I know what the mass is and I have a rough idea of the center of gravity so I would like to assign these values to the imported model so that the CG and mass in my tractor model is correct. The problem is, I can't seem to figure out how to assign mass to a point. Anyone have any ideas?
when i start to download Creo 2.0 M090 with download manager it starts and then says "error" and then stops?did anybody face the same issue?what could be wrong?i have treid using inter explorer 8 mozilla and google chrome
I'm wondering if anyone has done any work with Splines and holding the length to a fixed value? This assumes that the endpoints could not get any further apart than a straight line, but as the ends got closer together (by way of some other constraints) the spline would "buckle" (for lack of a better term) to mimic the behavior of a semi rigid component (like a hose).
How to change the spline line properties in partial view in 2 d ex: i want to set the partial line boundary like phantom , centreline or so on ?
Does anybody know how to get an angular dim as shown in the image? (in Creo Parametric 2.0),
Have attached image for your refernce .It would be better if some one have created & share the profile
Does anyone know how to change theSpline Boundary Line ofa Partial,or Detail View?I know there is the option tonot "show spline boundary on view".I cannot seem to find away to show Spline Boundary Linewith a different line type. A way around thisI sometimes remove spline display line and manually sketch in a spline and thenchangeline type. It's too much manual work and I always have to re-adjust it whenthe view boundary changes. I was hopingsomeonemight know away to solve this.I`m currently using Creo 2.0 Parametric 2.0
Hi again, Also, where is the Materials Folder? (and WHY is it so hard to add a newmaterial to it?) -Nate
Is it possible to add custom profiles to the framework.The rectangular and square tubes are with rounded corners and for calculating purposes we need them to be straight.Also for we use custom profiles for our customers.We used the same trick in Inventor, but in Creo I don't know it this possibility is here
I just had a phone conversation with a guy that sells 3D scanners. He doesn't sell any of the scanners that will do what I want, so he didn't have an axe to grind.He's been in this industry for quite a number of years and according to him, none of the scanners I listed will do what I want.He suggested the following scanners for doing room scans. None of these are cheap, but they do exactly what I was looking for a scanner to do.Surphaser
Once a parameter is created, is there a way to change from the Parameter Type (ex: String, Real Number, etc) after hitting the OK button?? Or do you have to delete the parameter and create a new one??
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.