Recently active
Allow an Annotation to be related to another annotation/weldnote.Isn't this done by selecting Offset instead of picking a placement?
I could write a SolidWorks add-in to do this in about a minute, but I don't know the Creo API yet. Does anyone know if there is an option to do this or an existing add-in? I didn't mind the Window menu from Wildfire, but the tiny icon in Creo is inconvenient.Thanks
Can anyone tell please?
I have a table that I have been using that has "&todays_date" which has been working well and shows the date as 10-MAR-15.I copied this table over to another table, but similar and when I go to use this new table with "&todays_date" it works also, but shows the date as Mar-10-15.How do I fixed the format of the date when they are both "&todays_date"Thanks, Dale
Is there any option available in Creo, which will Automatically adjust Table Width size according to text length.?
does anyone know if there is a limit to the amount of mapkeys you can have? I dont seem to be able to create any more than 83 which seems like an odd limit
The following meshing of a 2D plane wanted.But I get the following meshing.The points marked are inserted automatically by software. AutoGEM Control "Edge Distribution"used to control .Any one have any idea how to improve it?
I need to make a moving model of my robot and for that i need force motors, dynamic motion, gravity, friction, etc. So any help would be but welcome.
When I open *.x_t file in the Creo 2 I received solid model.When I open the same *.x_t file in the Creo 3 I received faced model.How need change setting in Creo 3 to receive solid model after opening *.x_t file?
I have downloaded 30 days of trial version of creo 3.0 on my laptop but I cannot find 'setup' folder or neither of 'parametric.exe'.Anybody can help me out to set up or run this trial version properly?Thanks.
What does the TBD mean next to red, green, and yellow regen status lights ? (see attached jpg)
This is in my flat state simp rep or in any combination state for that matter. Any ideas on what may be the issue? They show up as suppressed in the detail tree. Creo Parametric 2.0 M120.
I need to work on one of my models urgently!So Please!
PTC should restart it support for Linux for Creo.
sir , my name is kashyap and I am getting problem while entering the code in it ... the box where I supposed to enter the code is not working . and the curser on the box is totally fail to work on in the box.
Short question:Is there any way to make Creo run a mapkey when opening a file?
I have created a channel using boundary blend command. For this purpose I used two longitudinal curves and seven sections as shown bellow. The starting section is circle and the last one is almost rectangular.When I use boundary blend command to create channel, lots of lines were appeared on the quilt( see figure bellow). Does anyone know how I can remove them?
OK, I'm using this thing a lot today.Does anyone know if it is possible to get the area of a Cross Section fromPro/E?Thanks,Erik Olsen
Hallo zusammen,in der neuen Forumsumgebung tue ich mich erstaunlich schwer.a) finde ich den Zugang zum deutsche Forum sehr kompliziertb) finde ich keinen Schalter eine Antwort als "richtig" bzw. "hilfreich" zu markierenc) finde ich den Zugang zu den Katalogen nicht, in der Teilnehmer ihre Erzeugnisse präsentieren.Ich glaube umständlicher ging es wohl kaum oder?Gruß Werner
Hallo zusammen,im augenblick habe ich irgendwie ein Brett vr dem Kopf.Selbst die beigelegte Onlinehilfe gibt mir keinen Aufschluß.Ich habe mehrere 3D-Kurven (Geraden und Bögen), die ich zu einer Flächeformen möchte.Ich schaffe es nicht eine Verbindungslinie zwischen den auf verschiedenen Ebenenliegenden 3D-Kurven aufzubauen, geschweige eine Fläche zu erzeugen.Ich bevorzuge Express 4.0, kann aber auch mit Express 6.0 arbeiten.Zum Verständniß lege ich 2 Bilddateien und die Expressdatei bei.Mit Gruß Werner
Damián CastilloCAD & Administration ManagerEngineering DepartmentHensley Industries, Inc.
Anyone using peck tables? If so would you be willing to share and example?Thanks in advance.
I am working on a lathe post for the first time in a while. Our lathe offset command needs to be 6 digits, tool nose radius, tool number, offset number like T010101. Is there a FIL command to make the 4 digit number repeat 2 more digits like the previous 2?
Does anyone remember changing their splash screens if so how do you do it now, am on Creo 3.
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.