Recently active
Dear all,There are lots of CAD softwares in market. As per my knowledge, I couldn't find any such regeneration happening in any other CAD tool.Please share information regarding regeneration in creoRegards,Sandeep
Is there a way to migrate some fonts fonts from CATIA to CREO like SSS1, SSS2... or any others? How can I do that?
We have legacy Pro/E data here and I would like to see how well Creo 4 can convert it to Solidworks.Can someone convert this file to Solidworks using Creo 4 please.
What does the dollar ($) symbol mean in configuration editor? I'm assuming it's shortening the address, but how would you view the entire address if this is the case.Thanks!
How to create acme double lead thread in creo?
All,Would like your experience with the Mirror Command?After creating a mirror component, how does downstream folks utilizing EPDM?Etc. etc..I look forward to the replies
I go to the "learning exchange" but when I look for a subject it takes me to Creo. I have pro-e 5.0 and need to find tutorials for help. Can anyone suggest suggest anything, even Youtube doesn't have much on Pro-e
Hi all,Actually i have to bring the density of assigned material in the parameter column automatically.For this i have filled the relation tab "DENSITY=MP_DENSITY" value.But it will not bring the assigned material density automatically.In other case, I faced the below problemWhen i assigning the new material, It will ask the below notification and took the current model density value for the assigned material. Actually it over rides my material file density value.Please suggest to avoid these kind of problems.Thanks.
Hi,In our material library we have very few materials only. Now i have to add more material files in creo material library.Please suggest for creating material library files. By uday
bonjours , voici un site expliquant cette méthode , auriez vous une méthodologie avec creo SVPmerciFoundry - Lexicon
Hi everyoneI just test the GPS possibilities in Creo4 and make a fit-gap-analyze.I upload an attachement to this discussion, this shows only some uscases (3 of them) of the ISO standard and we want to realize this in 3D (Creo4)Perhaps someone has this done before or any suggestion?Thanks a lot
Do anyone know, in what format we need to save the creo template to open it in Solidworks???
where can we download creo4.0?thanks!
I am placing General Notes in an Annotated ModelHowever, I would like to know if there is a way to incorporated into the General Notes a "Hexagon" symbol within the Text Editor.For exampleIs there a script that exist to place a hexagon note around the number?thus the hexagon shape is flexible based on how many digitsI look forward to replies.Thank youRay
I read that Creo 4.0 is available for download since December 15 but even today if I log in and go to "Order or download Software Updates" I can only see up to Creo 3.0. Is there some trick to force the refresh of the list (I remember something like this in the past) or is Creo 4.0 not available right now? Our company has active maintenance.
What is the number 1 enhancement that you are looking forward to using in CREO 4
I'm wondering if you MBD practitioner folks out there can provide an opinion upon a point of view that is prevailing right now at my division regarding usage of models to document assemblies.The 2D situation is that many assembly drawings are considered to not show so much detail of the underlying parts as to demand a new version is generated as sub-components are iterated. Thus it is currently deemed perfectly acceptable to have a 2D PDF of an assembly drawing that is technically built from an OOD configuration. We say things like 'the assembly drawing is only intended to act as guidance for assembling' and 'specs for lower level parts are controlled by separate lower level design outputs'So now we fast forward to MBD or in our eyes 3D model based definition to be clearer. The same logic apparently results in a conflict because the definition of the assembly is much higher a viewer can e.g. isolate a single component and then end up 'confused' or worse. So the people who hold the prev
Is there a way to control text size in MBD? Especially frustrating with a family table that has small and large parts. Appears Creo defaults to a text size dependent on the model size.
假如目前我的工作目录是A,在A下面建了一个装配文档1.asm。然后从B目录下检索了一个零件(2.prt)装入1.asm 。然后用replace——by copy工具、选项在1.asm下创建一个零件(3.prt)替换掉零件(2.prt)。现在保存文档。发现新建的零件(3.prt)保存在B目录下。我的问题是怎样设置config,才能使新建的零件(3.prt)保存在A目录下呢?
Frankly, the text editor s#(ks. I found the older one in the last version I used (creo elements / pro 5.0) outdated and clunky, but it worked. This new one is flat infuriating. Am I stuck with it? I have trouble reading it and/or manipulating it. It seems to "time out" when you're trying to change text size etc.Also, I really don't find dwg mode that much better than that "worst EVER" ribbon interface in the old version, if at all. I just started using dwg mode, but, so far, I am NOt impressed. Even the old WF interface was better......Ugh!
This weekend I was tasked with modifying a piece made almost entirely of boundary blends. Typically this wouldn't be an issue and an easy fix but this time the BB's are dependent on other BB's. My model tree is almost entirely BB's. I don't have a lot of experience with these as I'm usually designing with solids. The biggest problem here is that the surfaces that need changing are smack dab in the middle of the model tree. They are not grouped together either, for example Boundary Blend 8, 9, 13, 15, and 27 need to be changed. Is it possible to lock these BB's in place or somehow reference them to other geometry without the entire model failing?
Hello To All,When you are assembling items in Creo, and you have to use angle offset. You have to use negative value, but as soon as you hit regenerate it jumps to the positive value. Is there a way to get it where it will stay the negative value?Thanks Billy
Hi folks,I have a question about using mapkeys - in different creo languages.Problem: I create mapkey in Creo (German version) - with the mapkey, I need to select old drop down menu (all expresion are in the German), but if I open the mapkey - system wrote everything in the original English version.For example: #SHOW;#ERASE;Result: I can not use this mapkey, because system looking for English expresion >> no German.Can you help me with configuration option for this problem?Thanks,Vladimir
I have purchased student academic PTC CREO today. I have downloaded successfully, but it is shutting down itself. There is a message from the screen: " register with quality agent to be able to PTC CREO".
Already have an account? Login
No account yet? Create an account
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.