Skip to main content
May 18, 2022 6:25 PM UTC
Question

Hole callout does not update

I have a strange problem that hole callout does not update if value of hole dimension change:

dveljkovic_0-1652897926405.png

C'bore depth is 20mm. And yet, hole callout says 8mm, which is wrong:

dveljkovic_1-1652897961592.png

 

While parameters are correct as value entered:

dveljkovic_2-1652898008838.png

Hole text in .hol file is:

C'BORE-&PATTERN_NO{0:X}/FOR &FASTENER_ID/<CTRL-A>v<CTRL-B><CTRL-A>n<CTRL-B>&CBOREDIAM[.2]<CTRL-A>x<CTRL-B>&CBORE_DEPTH[.1]

 

As in hole annotation:

dveljkovic_4-1652898114925.png

I also changed c'bore diameter value and it's value in hole callout did not change.

I am using 5.0.6 version.

Has anyone had a problem like this?

10 replies

May 18, 2022 7:04 PM UTC

Well, your names for the hole parameters are inconsistent.

 

Parameter name:

CBORE_DIAMETER

in your .hol file:

CBOREDIAM

 

Parameter name:

CBORE_DEPTH

in your note:

CBOREDEPTH

 

May 18, 2022 7:06 PM UTC

I did not make those parameters. Creo does.

May 19, 2022 1:13 AM UTC

What I have found out is that when you place first hole, that callout is set fo good on that model!?! Even when I press reset button. This should not be the case.

May 19, 2022 6:51 AM UTC

Maybe you have this setting active?

hole_file_resolution use_internal

see

About Embedding Hole Files into a Part Model 

 

Also, pretty sure that any changes to the .hol files may require you to restart Creo and reload the model...

 

 

May 19, 2022 10:50 AM UTC

No. "replace_with_external" is currently active. I am restarting Creo like crazy. New .hol file changes affect only new details. Old one are stuck on old .hol settings.

May 19, 2022 1:14 PM UTC

@dveljkovic wrote:

I have a strange problem that hole callout does not update if value of hole dimension change:

dveljkovic_0-1652897926405.png

C'bore depth is 20mm. And yet, hole callout says 8mm, which is wrong:

dveljkovic_1-1652897961592.png

 

While parameters are correct as value entered:

dveljkovic_2-1652898008838.png

Hole text in .hol file is:

C'BORE-&PATTERN_NO{0:X}/FOR &FASTENER_ID/<CTRL-A>v<CTRL-B><CTRL-A>n<CTRL-B>&CBOREDIAM[.2]<CTRL-A>x<CTRL-B>&CBORE_DEPTH[.1]

 

As in hole annotation:

dveljkovic_4-1652898114925.png

I also changed c'bore diameter value and it's value in hole callout did not change.

I am using 5.0.6 version.

Has anyone had a problem like this?


Hi,

I think you have to upload your .hol file, if you need to resolve the problem. If the file is secret then open Case at PTC Support and send the file to PTC.

May 19, 2022 1:33 PM UTC

Hi Martin, .hol file is not secret. But, .hol file is not the problem. Creo is. It only reads .hol file for new models (correctly), while old models read "internal" hol file (or at least I think that's what is happening). I contacted PTC support, and will se hat they have to say.